INCRA Miter Slider SE User Manual

Incra miter slider se, Important

Advertising
background image

®

Adjustable Steel Runner for Sliding Jigs and Fixtures

INCRA Miter Slider

SE

T

he new

Miter Slider SE embodies the smooth gliding attributes of the popular Original

Aluminum Miter Slider in a heavier, more robust bar design featuring all steel construction.
Just like the original Miter Slider, the

New Miter Slider SE is compatible with all of the Build It

System components including the pre-drilled Build It Panels. Since the mounting procedures
are exactly the same, the original Miter Slider Owner’s Manual is provided to include several
free Build It System Jig Plans. You’ll also want to take a look at our website at

www.incra.com

for a selection of

FREE step by step jig plans

for a variety of applications in your shop.

If you prefer to design your own Jig and Fixtures, just follow the instructions under the heading
“General Mounting” starting on page 2 of the Miter Slider Owner’s Manual. The only
differences of note are as follows:

In Step 4, the mounting holes on the SE bar are the smaller #10-24 threaded holes. When
marking the “expansion screw locations”, you’ll only need to mark the expansion locations for
the

Miter Slider SE bar that have a white disc. The black discs do not need to be marked

because they are not adjustable. You can also mark any of the larger 1/4-20 hole locations
as desired for later use with user supplied push knobs or clamping fixtures. Alternately, you
can use the dimensions shown in

Fig. 1 below to layout the mounting and expansion screw

hole locations.

In Step 6 and Fig. 7, the expansion screw access holes need to be 1/2” diameter rather than
the 1/4” specified. If you have marked any of the 1/4-20 holes for use with hold downs or
push knobs, drill them with a 5/16” diameter bit.

Unlike the original Miter Slider, your

New Miter Slider SE includes T-slot retainers for both

ends of the bar. This keeps your jig securely engaged in any T-slot miter channel for safe
operation during wide cutting operations and ensures that your jig stays on the table if you
over extend in either direction. To remove the pre-assembled clips for non T-slot applications,
just remove the fastener. When replacing the retainer clips, make sure that the raised rim
around the retainer’s threaded hole is nested into the large mounting hole on the bar before
tightening the fastener,

Fig 2.

Manufactured by: Taylor Design Group, Inc. P.O. BOX. 810262 Dallas, TX 75381

©2009 by Taylor Design Group. All rights reserved. Rev.04.20.09

W W W . I N C R A . C O M

IMPORTANT:

The Miter Slider SE is not recommended for stationary jigs

that must be locked into position within a miter slot. The

standard aluminum Miter Slider is the best choice for these

applications.

Miter Slider SE

System

it

Raised rim on retainer clip

Fig.1

Mounting Hole Dimensions

Fig.2

T-Slot Retainer Clip

3-3/4”

2-1/2”

2-1/2”

3-3/4”

3-3/4”

2-1/2”

2-1/2”

3-3/4”

3-3/4”

2-1/2”

2-1/2”

3-3/4”

1/4-20 Hole Spacing

10-24 Hole Spacing

5-3/16”

7-1/2”

7-1/2”

Expansion disc spacing

3-3/4”

2-1/2”

2-1/2”

3-3/4”

2-1/2”

2-1/2”

3-3/4”

3-3/4”

5-1/8”

7-1/2”

Expansion disc spacing

1/4-20 Hole Spacing

10-24 Hole Spacing

Advertising