Omnitron Systems Technology FlexSwitch 600XC 8U - Manual

User Warranty Registration
Please register on-line
@ http://www.omnitron-systems.com
or complete both sides
and mail or fax this registration form to:
Omnitron Systems T
echnology
, Inc.
27 Mauchly #201 Irvine, CA 92618, USA Fax: (949) 250-6514
Name:
_________________________________________________
Company:
______________________________________________
Address:
______________________________________________ ______________________________________________
City: ___________________ State: _______ Zip Code:
________
Country:
_______________________________________________
Phone: ____________________ Fax:
_______________________
E-mail:
_________________________________________________
Please complete both sides of this form
FlexSwitch TM 600XC 8U
User Instructions
Description:
The FlexSwitch TM 600XC described here is an eight-port
10/100 auto-sensing switch. It operates in half duplex
(HD) or full duplex (FD).
Ext. Power Int. Power
Model Model UTP RJ45
6700 6500 8 @ 10/100
Power Adapter Notice:
1. When used with an external power adapter (models
67xx), this product must only be used with Omnitron
Supplied Power Unit model number 9112-PS.
2. When used with an external power adapter (models
67xx), this product is intended to be and must be used
only with a Listed Direct Plug-In Power Unit marked
“Class 2” and rated at 9Vdc, 1.2 Amp.
3. Models using internal power supplies (models “65xx”)
are capable of auto switching from 100-230V, and
are supplied with a U.S. type NEMA 5-15 power cable.
4. For products being shipped outside of the U.S., the
user is required to install a properly grounded IEC
320-appliance cable with a minimum rating of 10 AMPs.
5. User-supplied cables must meet the required safety
agency approvals, applicable international standards
and electrical ratings for the region.
WARNING!
Before inserting the Power Adapter, verify that
the power on the unit is appropriate
for your AC line voltage source.
Mounting and Cable Attachment:
The FlexSwitch 600XC can be used as a tabletop unit
or wall-mounted using a wall-mounting kit.
After connecting to an appropriate power outlet, attach
the FlexSwitch 600XC UTP ports via category 5 cables
to properly configured and operational 10Base-T or
100Base-Tx Ethernet workstations, hubs or switches.
Verify that the LEDs display the expected (10 or 100, half
or full duplex) status. Note that UTP port one has a built-
in crossover switch that facilitates the usage of a straight-
through cable for a hub, switch or workstation connection.
Switch Settings:
UTP “Crossover” Switch: When connecting port one
to a hub or switch, set the switch to “Crossover.” When
connecting to a workstation, set it to “Straight-Through”
(factory setting).
LED Indicators:
Function Color Description
Power
Power
Yellow Off: No power detected
On: Power detected
Copper:
10/100
Green/Yellow Yellow On: 10
Green On: 100
Yellow or Green Flashing:
Activity detected
FDX/HDX Green Off: Set to Half-Duplex
On: Set to Full-Duplex
Technical Support
For help with this product, contact our Tech Support:
Phone:
(949) 250-6510
Fax: (949) 250-6514
Address: Omnitron Systems Technology, Inc.
27 Mauchly #201
Irvine, CA 92618 USA
Email: [email protected]
URL: http://www.omnitron-systems.com
User Warranty Registration
Please register online at
http://www.omnitron-systems.com
or complete both sides
and return this form to Omnitron Systems. FlexSwitch T
ype: ________ Fiber T
ype:_______Connector: _______
Model:
_________________________________________________
Serial Number: ______________ Purchase Date:
______________
Purchased From: _________________________________________ Address:
______________________________________________
City: ___________________ State: _______ Zip Code:
________
Country:
_______________________________________________
Comments and Suggestions:
_______________________________
______________________________________________________ ______________________________________________________
Please complete both sides of this form
Notes:
____________________________
____________________________
____________________________
____________________________
____________________________
____________________________
____________________________
____________________________
________________________________
______________________________
_______________________________
______________________________
_____________________________
_____________________________
____________________________
_____________________________
_____________________________
Warning
The operating description in this Instruction Manual is
for use by qualified personnel only. To avoid electrical
shock, do not perform any servicing of this unit other
than that contained in the operating instructions, unless
you are qualified and certified to do so by Omnitron
Systems Technology, Inc.
Caution
All user-required operations can be performed without
opening the unit. Never attempt to open or remove the
cover or tamper with the unit.
Warranty
This product is warranted to the original purchaser
against defects in material and workmanship for a period
of TWO YEARS from the date of shipment. A LIFETIME
warranty may be obtained by the original purchaser by
REGISTERING this product with Omnitron within 90 days
from the date of shipment. TO REGISTER, COMPLETE
AND MAIL OR FAX THE REGISTRATION PORTION
OF THIS INSTRUCTION MANUAL TO THE INDICATED
ADDRESS. Or you may register your product on the
internet at http://www.omnitron-systems.com. During the
warranty period, Omnitron will, at its option, repair or
replace a product which is proven to be defective.
For warranty service, the product must be sent to an
Omnitron designated facility, at Buyer’s expense.
Omnitron will pay the shipping charge to return the
product to Buyer’s designated US address using
Omnitron’s standard shipping method.
Limitation of Warranty
The foregoing warranty shall not apply to defects resulting
from improper or inadequate use and/or maintenance
of the equipment by Buyer, Buyer-supplied equipment,
Buyer-supplied interfacing, unauthorized modifications
or tampering with equipment (including removal of
equipment cover by personnel not specifically authorized
and certified by Omnitron), or misuse, or operating
outside the environmental specification of the product
(including but not limited to voltage, ambient temperature,
radiation, unusual dust, etc.), or improper site preparation
or maintenance.
No other warranty is expressed or implied. Omnitron
specifically disclaims the implied warranties of
merchantability and fitness for any particular purpose.
Exclusive Remedies
The remedies provided herein are the Buyer’s sole and
exclusive remedies. Omnitron shall not be liable for any
direct, indirect, special, incidental, or consequential
damages, whether based on contract, tort, or any legal
theory.
Doc #: 040-06700-000 4/00