Omnitron Systems Technology FlexCeiver 10B2 - Manual

DOC No. 040-04220-001 FlexCiever 10B2, Page 1/2
FlexCeiver TM 10B2 User Instructions
Description:
The FlexCeiver TM family of transceivers are compatible
with IEEE 802.3 and Ethernet Versions 1.0 / 2.0. They
enhance networking media connectivity using 10Base-
FL with single-mode (SM) and multimode (MM) fiber,
10Base-2 thin coax and 10Base-T twisted pair (UTP).
All FlexCeivers have a 15-pin AUI connector that attaches
to a mating AUI connector mounted on hosting Ethernet
DTE equipment such as a workstation or a PC, or on a
repeater such as a hub or a switch.
This FlexCeiver 10B2 model is described here:
Model Maximum Distance Station Count
4220 185 meters / 606 ft. 30 maximum
The 4220 model provides a switch selectable coax line
termination mode that allows a RG58 type coax cable to
be terminated using an internal 50 ohm termination ele-
ment. This should be used only when connecting the
FlexCeiver at the end of a coax segment. It eliminates
the need for an external “T” connector and a termination
element. Note that this termination must be disabled
when the FlexCeiver is not at the end of the cable.
Mounting:
Insert the Omnitron FlexCeiver 10B2 into the 15-pin AUI
port on a PC, workstation, hub or switch; slide the con-
nector latch locking it into place. If an AUI cable is used,
it is limited to 50 meters (164 ft.). If connecting the
FlexCeiver at the end of a coax segment, attach the coax
cable directly into the FlexCeiver’s BNC coax connector.
If connecting along the coax line (not at the end), use a
“T” connector to tap into the cable. Note that the total
length of the cable must not exceed 185 meters (606 ft.)
and the number of stations on the coax segment must
not exceed 30 stations (per IEEE 802.3 specification).
Switch Settings:
“SQE” switch: When attaching to a PC (or a worksta-
tion), the SQE switch should be set to “SQE Enable”
(factory setting). When connecting to a hub or a switch,
it should be set to “SQE Disable.”
“Termination” switch: When attaching anywhere along
a coax cable except at the end, the Termination switch
should be set to “Termination Disabled” (factory setting).
When attaching to the end of a cable, it can be set to
“Termination Enabled.” Note that when the switch is set
to “Termination Enabled,” an external termination ele-
ment must not be attached.
LED indicators:
LED Color Description
Power On Green Power applied from attached unit
SQE Enable Yellow “SQE Enable” indicator
Technical Support:
If you encounter problems in installing or maintaining
this product, contact Omnitron Technical Support:
Phone: (949) 250-6510
Fax: (949) 250-6514
Email: [email protected]
Address: Omnitron Systems Technology, Inc.
27 Mauchly #201
Irvine, CA 92618 USA
User W
arranty Registration
Please complete both sides and mail or fax this registration form to:
Omnitron Systems T
echnology
, Inc.
27 Mauchly #201 Irvine, CA 92618 USA Fax: (949) 250-6514
Name:
_________________________________________________
Company:
______________________________________________
Address:
______________________________________________ ______________________________________________
City: ___________________ State: _______ Zip Code:
________
Country:
_______________________________________________
Phone: ____________________ Fax:
_______________________
E-mail:
_________________________________________________
Please complete both sides of this form
FlexCeiver TM 10B2 User Instructions
Description:
The FlexCeiver TM family of transceivers are compatible
with IEEE 802.3 and Ethernet Versions 1.0 / 2.0. They
enhance networking media connectivity using 10Base-
FL with single-mode (SM) and multimode (MM) fiber,
10Base-2 thin coax and 10Base-T twisted pair (UTP).
All FlexCeivers have a 15-pin AUI connector that attaches
to a mating AUI connector mounted on hosting Ethernet
DTE equipment such as a workstation or a PC, or on a
repeater such as a hub or a switch.
This FlexCeiver 10B2 model is described here:
Model Maximum Distance Station Count
4220 185 meters / 606 ft. 30 maximum
The 4220 model provides a switch selectable coax line
termination mode that allows a RG58 type coax cable to
be terminated using an internal 50 ohm termination ele-
ment. This should be used only when connecting the
FlexCeiver at the end of a coax segment. It eliminates
the need for an external “T” connector and a termination
element. Note that this termination must be disabled
when the FlexCeiver is not at the end of the cable.
Mounting:
Insert the Omnitron FlexCeiver 10B2 into the 15-pin AUI
port on a PC, workstation, hub or switch; slide the con-
nector latch locking it into place. If an AUI cable is used,
it is limited to 50 meters (164 ft.). If connecting the
FlexCeiver at the end of a coax segment, attach the coax
cable directly into the FlexCeiver’s BNC coax connector.
If connecting along the coax line (not at the end), use a
“T” connector to tap into the cable. Note that the total
length of the cable must not exceed 185 meters (606 ft.)
and the number of stations on the coax segment must
not exceed 30 stations (per IEEE 802.3 specification).
Switch Settings:
“SQE” switch: When attaching to a PC (or a worksta-
tion), the SQE switch should be set to “SQE Enable”
(factory setting). When connecting to a hub or a switch,
it should be set to “SQE Disable.”
“Termination” switch: When attaching anywhere along
a coax cable except at the end, the Termination switch
should be set to “Termination Disabled” (factory setting).
When attaching to the end of a cable, it can be set to
“Termination Enabled.” Note that when the switch is set
to “Termination Enabled,” an external termination ele-
ment must not be attached.
LED indicators:
LED Color Description
Power On Green Power applied from attached unit
SQE Enable Yellow “SQE Enable” indicator
Technical Support:
If you encounter problems in installing or maintaining
this product, contact Omnitron Technical Support:
Phone: (949) 250-6510
Fax: (949) 250-6514
Email: [email protected]
Address: Omnitron Systems Technology, Inc.
27 Mauchly #201
Irvine, CA 92618 USA
User W
arranty Registration
Please complete both sides and mail or fax this registration form to:
Omnitron Systems T
echnology
, Inc.
27 Mauchly #201 Irvine, CA 92618 USA Fax: (949) 250-6514
Name:
_________________________________________________
Company:
______________________________________________
Address:
______________________________________________ ______________________________________________
City: ___________________ State: _______ Zip Code:
________
Country:
_______________________________________________
Phone: ____________________ Fax:
_______________________
E-mail:
_________________________________________________
Please complete both sides of this form