Scan Tech HFW Power Generator - Manual

Scan Tech AS
Finnestadsvingen 23 Po.Box. 738 Tel. +47 51 54 54 00 [email protected]
4029 Stavanger 4001 Stavanger Fax +47 51 54 54 50 www.scan-tech.no
Model Engine Power
kVA kW
P.R.P(1)S.By(2)P.R.P(1) S.By(2)
Gov.
(3)
Cyl Feed.
(4)
Dimensions mm.**
L W H
Weight**
Kg
Fuel
Tank Ltr
Fuel Cons.*
L/h.
HFW‐60 T5 NEF45 SM 1A 60 63 48 50 M 4L TC 2 750 1 100 1 500 1 525 175 13,7
HFW‐75 T5 NEF45 SM 2A 73 80 58 64 M 4L TC 2 750 1 100 1 500 1 550 175 17,1
HFW‐100 T5 NEF45 TM 2A 100 108 80 86 M 4L TCA 2 750 1 100 1 500 1 670 175 22,0
HFW‐135 T5
NEF67 TM 2A 130 143 104 114 M 6L TCA 3 300 1 200 1 800 2 295 245 29,0
HFW‐160 T5 NEF67 TM 3A 160 175 128 140 M 6L TCA 3 300 1 200 1 800 2 365 245 36,0
HFW‐180 T5 NEF67 TE 2A 180 194 144 155 E 6L TCA 3 300 1 200 1 800 2 390 245 ‐
HFW‐200 T5 NEF67 TE 2A 200 220 160 176 E 6L TCA 3 300 1 200 1 800 2 435 245 41,3
HFW‐250 T5 C87 TE 1D 250 275 200 220 E 6L TCA 3 800 1 400 2 105 3 840 445 ‐
HFW‐305 T5 C10 TE 1D 300 330 240 264 E 6L TCA 4 100 1 600 2 210 4 135 590 ‐
HFW‐350 T5 C13 TE 2S 350 390 280 312 E 6L TCA 4 100 1 600 2 210 4 295 590 ‐
HFW‐400 T5 C13 TE 3S 400 440 320 352 E 6L TCA 4 100 1 600 2 210 4 480 590 ‐
*Fuel consumption measured in ltr/hr. at 100% load at 1500 rpm at 50Hz.
**Weights and dimensions are subject to variations depending to the
generators configuration solicited by the customer.
To be consulted by Scan Tech.
Ambient reference conditions:
1 000 mbar, 25°C, 30% relative humidity. Rating according to ISO 3046
1 – P.R.P. Prime Power – ISO 8528: Prime power is the maximum power
available during a variable power sequence, which may be run
for an unlimited number of hours per year, between stated maintenance
intervals.The permissible average power output during a 24 hours period
shall not exceed 80% of the prime power.10% overload available for
governing purposes only.
2 – Standby power (ISO 3046 Fuel Stop power): Power available for use at variable loads for limited annual
time (500h), within the following limits of maximum operatingtime: 100% loads 25h per year – 90% loads
200h per year. No overload available.
Applicable in case of failure of the main in areas of reliable electrical network.
3 – M= Mechanical speed governor.
E= Electronic speed governor.
4 – TC = Turbocharged; TCA = Turbocharged and aftercooled.
Scan Tech reserve the right of modify any characteristic without prior notice. Weights and dimensions based on products standards and sec / illustrations may include optional equipment.
Technical data here described correspond with the available information of the moment of printing. Industrial design under patent.