Sportsliter Solutions SLS Series Floodlight - Manual

SLS SERIES FLOODLIGHT
INSTALLATION AND SERVICING INSTRUCTIONS
SLS0025 SLS Series Instruction-A 1/14
GENERAL SAFETY WARNING!
Dangerous voltages exist within these fixtures and all precautions usually observed in
handling high voltage equipment should be observed when replacing lamps, installing or
otherwise servicing these fixtures.
WARNING!
To reduce fire and shock hazard: Disconnect power before servicing. Install and maintain
fixture to meet all applicable codes. Ensure that fixtures and wiring are properly
grounded. Read and follow all instructions, electrical data markers, lamp carton warnings
and wiring labels before installing. Installation of fixture is to be preformed by a qualified,
licensed electrician only. The installer of this fixture is responsible for sale, secure
mounting suitable for the application. Once fixture is installed, give these instructions to
the equipment owner.
CAUTION!
• High temperature tempered glass sometimes ruptures spontaneously.
Install to minimize hazard of falling diced glass.
• This product is shipped in multiple cartons. Ballast/socket housings are shipped one per
carton while reflector/lens assembles and protective hulls are each shipped one to five
per carton.
• To identify individual NEMA beam spreads the following cross reference chart is
provided. “I.D.” labels are located on the top of each reflector.
NEAM
BEAM
M.H. H.P.S
100W, 1500W, 1650W 1000W 400W
2 X 2 SLSR2 SLSR2S SLSR2
3 X 3 SLSR3A N/A N/A
4 X 4 SLSR4 SLSR4S SLSR4
5 X 5 SLSR5 SLSR5S SLSR5
6 X 6 SLSR6 SLSR6S SLSR6
*Reflector NEMA beam spreads must be matched to ballast housing assembles. The 10th digit of the ballast housing
catalog number identifies the NEMA type required.
Example: SLS-1000H-158 (NEMA ASSEMBLY)
Unpacking Instructions:
While unpacking, it is important to verify the location of all parts before
discarding any packaging materials.
Assembly Instructions: (See figures 1a, 1b, 1c, 1d)
Prior to assembly, use a marker to mark the optical assembly I.D.
number on the ballast housing (or cover) for later reference.
1.
PROTECTIVE HULL INSTALLATION (If no hull is included in your
installation, go to step #3) Place keyhole slots in hull (A) over the
mounting screws (B) and rotate the hull in a counter-close wise direction
unit it stops.
2. Place the gasket
(D) (supplied with the hull) over the mounting screws
inside the hull.
3. Place keyhole slots in reflector
(B) over the mounting screws (E) and
rotate the reflector in a counter-clockwise direction until it stops.
4.
1000 WATT HIGH PRESSURE SODIUM UNIT ONLY (If fixture is not
1000W HPS go to stop #6) Remove the top two(2) (E) and the bottom
two(2) (E) screws from the socket housing (C).
5. Place the black baffle (F) (supplied with reflector) into the reflector over
the holes and loosely install the top and bottom screws to
retain the baffle.
6. Place lamp support bracket
(G) (provided in ballast housing hardware
bag) directly under (2) screw heads inside the reflector
(or baffle if 1000W HPS).
7. Tighten the (6) mounting screws
(E). Minimum of 20 Inch lbs.
8. Install lamp.
9. Remove the lens assembly retaining screw
(AD) & nut (AE) from the lens
ring hinge.
10. Attach the lens assembly to the reflector by installing the screw through
the clearance holes in the reflector bracket and lens ring bracket. Drive
the screw
(AD) into the nut (AE) until the end of the screw goes totally
through the nut. Otherwise the nut may fall off.
11. Close the lens ring assembly.
12. Ensure the gasket is seated properly & snap the
(4) latches over the
reflector flange.
Mounting Instructions (See Figure 2)
This unit is supplied with a 5/8” or 3/4” x 2” bolt, nut, slit washer,
and toothed washer for mounting to crossarm style (flat surface)
mounting brackets. The bolt is captive but may be replaced with a
longer, hex head bolt if required. A 5/8” bolt, S.A.E. 5 minimum or
a 3/4” bolt, S.A.E. 2 minimum is require. A tenon adapter (Cat. No.
4024SLS) is available for pole top mounting.
1. Use the aiming plate as a template and mark the center of the small hole
on the crossarm
(L). Note: Position the forward edge parallel to the
crossarm mounting bracket.
2. Drill a .219” dia. hole through the steel crossarm at the location just
marked.
DO NOT drill through the aiming plate.
3. Using the supplied screw and nut, attach the aiming plate to the large
galvanized nail to attach the aiming plate.
4. Remove the nut
(AC), slit washer (AB), and toothed washer (AF) from
the main fixture mounting bolt (M).
5. Secure the fixture to the crossarm by placing the main fixture mounting
bolt through the toothed washer
(AF), the horizontal aiming plate (K),
and the hole in the crossarm.
6. Replace the slit washer
(AB) and nut (AC) on the main fixture mounting
bolt and tighten to 150 ft. lbs. IMPORTANT: Parts must be assembled as
shown in Figure 2.
Mounting Notes:
• Ensure that the crossarm has adequate strength to support your desire
number of fixture.
• SLS5010 mounting brackets are available when obstructions will not allow
center fixture mounting on three-fixture brackets.
• DO NOT mount fixtures directly to concrete.
C
E
A
B
F
G
D
Figure 1a
Figure 1b
B
G
Figure 1c
U
X
C
W
Z
AE
AD
Figure 1d
Drawing Number: 268-1117-9801 REV-B
Installation Instructions