Sportsliter Solutions SLS Remote Yoke Axial Optics - Manual

REMOTE YOKE HEAD AXIAL OPTICS
INSTALLATION AND SERVICING INSTRUCTIONS
GENERAL SAFETY WARNING!
Dangerous voltages exist within these fixtures and all precautions usually observed in
handling high voltage equipment should be observed when replacing lamps, installing or
otherwise servicing these fixtures.
WARNING!
To reduce fire and shock hazard: Disconnect power before servicing. Install and maintain
fixture to meet all applicable codes. Ensure that fixtures and wiring are properly
grounded. Read and follow all instructions, electrical data markers, lamp carton warnings
and wiring labels before installing. Installation of fixture is to be preformed by a qualified,
licensed electrician only. The installer of this fixture is responsible for safe, secure
mounting suitable for the application. Once fixture is installed, give these instructions to
the equipment owner.
CAUTION!
• High temperature tempered glass sometimes ruptures spontaneously.
Install to minimize hazard of falling diced glass.
• To identify individual NEMA beam spreads the following cross reference chart is
provided. “I.D.” labels are located on the top of each reflector.
NEAM
BEAM
M.H. H.P.S
100W, 1500W, 1650W 1000W 400W
2 X 2 SLSR2 SLSR2S SLSR2
3 X 3 SLSR3A N/A N/A
4 X 4 SLSR4 SLSR4S SLSR4
5 X 5 SLSR5 SLSR5S SLSR5
6 X 6 SLSR6 SLSR6S SLSR6
*Reflector NEMA beam spreads must be matched to ballast housing assembles. The 10th digit of the ballast housing
catalog number identifies the NEMA type required.
Example: SLS-1000H-050 (NEMA 5 ASSEMBLY)
Unpacking Instructions:
While unpacking, it is important to verify the location of all parts before
discarding any packaging materials.
Assembly Instructions: (See figures 1a, 1b, 1c)
Prior to assembly, use a marker to mark the optical assembly I.D.
number on the socket housing for later reference.
1.
PROTECTIVE HULL INSTALLATION (If no hull is included in your
installation, go to step #3): Place keyhole slots in hull (A) over the
mounting screws (B) and rotate the hull in a counter-close wise direction
unit it stops.
2. Place the gasket
(D) (supplied with the hull) over the mounting screws
inside the hull.
3. Place keyhole slots in reflector
(E) over the mounting screws (B) and
rotate the reflector in a counter-clockwise direction until it stops.
4.
1000 WATT HIGH PRESSURE SODIUM UNIT ONLY (If fixture is not
1000W HPS go to step #6): Remove the top two (2) and the bottom
two (2) screws from the socket housing
(C).
5. Place the black baffle (F) (supplied with reflector) into the reflector over
the holes and loosely install the top and bottom screws to
retain the baffle.
6. Place lamp support bracket
(G) (provided in ballast housing hardware
bag) directly under (2) screw heads inside the reflector
(or baffle if 1000W HPS).
7. Tighten the (6) mounting screws
(B). Minimum of 20 Inch lbs.
8. Install lamp.
9. Remove the lens assembly retaining screw
(AD) & nut (AE) from the lens
ring hinge.
10. Attach the lens assembly to the reflector by installing the screw through
the clearance holes in the reflector bracket and lens ring bracket. Drive
the screw
(AD) into the nut (AE) until the end of the screw goes totally
through the nut. Otherwise the nut may fall off.
11. Close the lens ring assembly.
12. Ensure the gasket is seated properly & snap the
(4) latches over the
reflector flange.
Mounting Instructions:
1. Install the fixture by mounting the yoke to the appropriate auxilliary fitter
with (2)
1 ⁄
2
”bolts, washers and nuts or (1) 3 ⁄
4
” bolt, washer and nut.
(supplied by others)
(Consult buyers guide for available mounting adapters.)
2. Attach the fixture to your pole or other mounting device. Ensure that
once installed, the fixture’s drain holes and reflector/lens hinge are
Installation Instructions
AE
AD
Figure 1d
FIGURE 1C
Drawing Number: 268-0922-9901