Bosch BOSCH GAS RANGE User Manual
Bosch Radio
Advertising
Table of contents
Document Outline
- About This Manual
- Safety
- Getting Started
- Parts and Accessories
- Table 1: Parts and Accessories
- Sealed Gas Burners
- Burner Caps
- Burner Grates
- Electronic Ignitor
- High Power Burner
- Precision Burner
- Flat Oven Racks
- 1. Grasp rack firmly on both sides.
- 2. Tilt rack up to allow stop into rack guide.
- 3. Bring rack to a horizontal position and press the rest of the way in. Rack should be straight and flat, not crooked.
- Control (Panel)
- Oven Control Panel
- Table 2: Oven Control Panel
- The Clock
- About the Clock
- Setting the Clock
- 1. CLOCK will be displayed and the hour digits will flash. Turn knob to select hour and AM or PM.
- 2. Press Time. CLOCK will still be displayed and the minute digits will flash.
- 3. Turn knob. Set minutes.
- 4. Press Time and the clock is now set.
- 1. Press Time. TIMER 1 flashes in display.
- 2. Turn knob to select CLOCK.
- 3. Press Time and hour digits flash.
- 4. Turn knob to change hours.
- 5. Press Time again and minute digits flash.
- 6. Turn knob to change minutes.
- 7. Press Time again and the clock is set.
- The Select Functions Menu
- 1. Press and hold COOKING MODE press pad for five (5) seconds. SELECT FUNCTION is displayed.
- 2. Turn knob slowly to desired feature. There will be a slight delay before each message (or feature) can be seen in the display. Turn knob slowly and wait approximately one second for display to show next feature.
- 3. Press START to choose the function.
- 4. Turn knob to desired setting and press START. When all settings for the function are complete, SELECT FUNCTION flashes again.
- 5. Press OFF to exit the Select Functions Menu.
- 1. Access SELECT FUNCTIONS Menu.
- 2. Turn knob clockwise until VOLUME is displayed.
- 3. Press Start.
- 4. Turn knob to select volume level Low, Medium or High.
- 5. Press Start.
- 1. Access SELECT FUNCTIONS Menu.
- 2. Turn knob clockwise until SELECT TEMP F-C is displayed.
- 3. Press Start.
- 4. Turn knob to select Fahrenheit (F) or Celsius (C).
- 5. Press Start to accept new selection.
- 1. Access SELECT FUNCTIONS Menu.
- 2. Turn knob clockwise until CLOCK DISPLAY is displayed.
- 3. Press START.
- 4. Turn knob to select ON or OFF
- 5. Press START to accept new selection.
- 1. Access SELECT FUNCTIONS Menu.
- 2. Turn knob clockwise until desired language is displayed.
- 3. Press Start.
- 4. Turn knob clockwise to select a different language.
- 5. Press Start to accept a language change.
- 1. Access SELECT FUNCTIONS Menu.
- 2. Turn knob clockwise until LOCK KEYS is flashing.
- 3. Press Start. KEY PAD LOCKED is displayed. The display will beep if a key is pressed to indicate that the keypad is locked.
- 4. To unlock keypads, press Cooking Mode and hold for 5 seconds. Display will read UNLOCKING KEY PAD.
- 5. When unlocked, the clock will again appear in the display.
- 1. Access SELECT FUNCTIONS Menu.
- 2. Turn knob clockwise until OVEN TEMP OFFSET is displayed.
- 3. Press START. 0˚ F is displayed.
- 4. Turn the knob to increase temperature in 25˚ F increments.
- 5. Press START to accept a temperature change.
- 1. Access SELECT FUNCTIONS Menu.
- 2. Turn knob clockwise until RESET DEFAULTS is displayed.
- 3. Press START. Display reads SELECT FUNCTIONS.
- 1. Verify that the oven is turned off.
- 2. Access SELECT FUNCTIONS Menu.
- 3. Turn knob clockwise until SABBATH OPTION appears.
- 4. Press START. BAKE will show in display and temperature will flash.
- 5. Turn knob to set oven temperature.
- 6. Turn oven light on if desired (press LIGHT).
- 7. Press START. Oven starts after 5 seconds.
- 1. Access SELECT FUNCTIONS Menu.
- 2. Turn knob clockwise until TIME FORMAT is displayed.
- 3. Press Start.
- 4. Turn knob to select 12 hour or 24 hour format.
- 5. Press Start to accept new selection.
- 1. Access SELECT FUNCTIONS Menu.
- 2. Turn knob clockwise until AUTO CONVECT BAKE is displayed.
- 3. Press Start.
- 4. Turn knob to select ON or OFF.
- 5. Press Start to accept new selection.
- Before Using the Appliance for the First Time
- Parts and Accessories
- Operation - Cooktop
- Operation - Oven
- About the Oven
- Operation
- Setting the Cooking Mode and Temperature
- 1. Press COOKING MODE.
- 2. BAKE will flash in the display.
- 3. If no change is made within 5 seconds, control will beep and flash. If this occurs, press START.
- 4. To change the cooking mode, turn knob.
- 5. Press START.
- 6. The selected mode will appear in the display, along with the default temperature for that mode, which will be blinking.
- 7. To select a different temperature, turn knob to the right or left (in 5˚ increments) to desired temperature.
- 8. Press START. If not pressed, oven automatically turns on in 5 seconds.
- 9. The display alternates between the cooking mode and preheat.
- 10. To change temperature during cooking, press Temperature. Turn the knob to select new temperature and press START.
- 11. Once cooking has been completed, press OFF to turn off oven.
- Using the Timer
- To set the timer:
- 1. Press TIME and TIMER 1 will flash in display.
- 2. Turn knob to set minutes. If setting only minutes, press START. Otherwise, continue to step 4.
- 3. Press TIME again and the hours will flash.
- 4. Turn knob to set hours.
- 5. Press TIME again. The TIMER is now set.
- 6. If TIME or START is not pressed, oven will begin beeping and timer display will begin flashing.
- 1. Press TIME. TIMER 1 will appear in display. Select either TIMER 1 or 2.
- 2. Press TIME. RESET TIMER 1 (2) appears in the display. Minute digits flash.
- 3. Turn knob clockwise or counterclockwise to change minutes.
- 4. Press TIME again and hour digits will flash.
- 5. Turn knob clockwise or counterclockwise to change hours.
- 6. Press TIME and new time is set.
- 1. Press TIME once. TIMER 1 flashes.
- 2. Turn knob to select CLEAR TIMER 1(2). Press TIME.
- 3. If Time pad is not pressed, range will beep and display will continue flashing.
- 4. Press TIME to return to the main screen.
- Using Timed or Delayed Cook
- Setting a Timed Mode
- 1. Press COOKING MODE.
- 2. BAKE will be displayed. To select a different cooking mode, turn the knob.
- 3. Press START.
- 4. Turn knob to select desired temperature.
- 5. Press TIME. TIMED BAKE appears.
- 6. Press TIME. SET BAKE TIME appears in the display and minutes flash.
- 7. Set minutes. Press TIME.
- 8. Hours Flash. Set hours. Press START.
- 9. TIMED BAKE appears in display and the oven begins to preheat.
- 1. Follow steps 1 through 5 above.
- 2. Turn knob until DELAYED BAKE appears.
- 3. Press Time. SET BAKE TIME appears in display and minutes flash.
- 4. Set minutes and then press TIME. Hours Flash.
- 5. Set hours and then press TIME. SET BAKE END appears in the display.
- 6. Press TIME.
- 7. Use knob to enter the time of day the oven will stop cooking or turn off.
- 8. Set hours and then press TIME.
- 9. Set minutes and then press TIME.
- 10. At the end of the programmed cooking time, the oven will automatically turn off. Display will show TIME COOK END and reminder beeps will sound. Press OFF to clear.
- 1. Press Time.
- 2. Turn knob to BAKE END or BAKE TIME.
- 3. Press Time.
- Setting the Cooking Mode and Temperature
- Getting the Most Out of Your Appliance
- Cleaning and Maintenance
- Cleaning - Cooktop
- Cleaning - Oven
- Daily Cleaning
- Cleaning Guidelines
- Avoid these cleaners
- Table 8: Oven Cleaning Chart
- Self Cleaning the Oven
- Preparing the Oven for Self Clean
- 1. Remove all utensils and bakeware.
- 2. Remove oven racks. If oven racks are left in the oven during the self-clean cycle, they will permanently lose the shiny finish and change to a dull dark finish. See Oven Cleaning Chart for proper care.
- 3. Wipe up excessive soil, spills and grease before self-cleaning the oven. Excess grease will cause flames and smoke inside the oven during self-cleaning.
- 4. Review illustration above. Some areas of the oven must be cleaned by hand before the cycle begins. Use a soapy sponge or plas...
- 5. Be sure oven light is turned off and the light bulbs and lens covers are in place. Do not operate oven without light bulb and cover in place.
- 1. Press COOKING MODE.
- 2. Turn knob until SELF CLEAN mode appears. Press START.
- 3. The default cleaning time is 4 hours. To change cleaning time, turn knob to change number of hours. Otherwise, continue to step 4.
- 4. Press START. SELF CLEAN flashes. Press START.
- 5. REMOVE RACKS appears in the display as a reminder to remove oven racks.
- 6. Press START again to begin the self- clean.
- 1. Press COOKING MODE.
- 2. Turn knob until SELF CLEAN mode appears. Press START.
- 3. The default cleaning time is 4 hours. To change cleaning time, turn knob to change number of hours. Otherwise, continue to step 4.
- 4. Press START.
- 5. Turn knob until DELAYED CLEAN mode appears. Press START.
- 6. SELF CLEAN END appears in the display.
- 7. Turn knob to enter the time of day you want the self-clean to end: Set hours, press time, set minutes.
- 8. Press START. The display will remind you to remove oven racks.
- 9. Press START. The display shows DELAYED CLEAN. The self-clean will automatically start at the appropriate time.
- 1. At the end of the programmed cleaning time, the oven will automatically turn off. SELF CLEAN END appears in the display. Press OFF to clear.
- 2. The self-clean mode may produce ash which will settle in the bottom of the oven. If this happens, remove ash with a damp cloth before using the oven.
- 3. Wipe rack edges with cooking oil to allow for proper glide. Wipe off excess.
- Cleaning - Drawer
- Maintenance
- Cooktop Maintenance
- Oven Maintenance
- Removing the Door
- 1. Be sure to read the WARNING below before attempting to remove oven door.
- 2. Open the door completely.
- 3. Flip lever on hinge toward you.
- 4. Close the door to approximately halfway open. Stop when you feel resistance from the hinge..
- 5. Holding the door firmly on both sides using both hands, pull the door straight out of the hinge slots. Hold firmly, the door is heavy.
- 6. Place the door in a convenient and stable location for cleaning.
- 1. Holding the door firmly in both hands, place hinges in hinge slots.
- 2. Open door all the way to expose hinges and slots. Push lever (one on each hinge) away from you (back toward range).
- 3. After moving the hinge brackets back down into position, be sure to close and open the door slowly to assure that it is correctly and securely in place.
- 4. Door should be straight, not crooked.
- 1. Read the WARNING above.
- 2. Turn off power at the main power supply (fuse or breaker box).
- 3. Remove the lens by unscrewing it.
- 4. Remove the light bulb from its socket by unscrewing it.
- 5. Replace the bulb with a new 40 watt appliance bulb. Avoid touching the bulb with fingers, as oils from hands can damage the bulb when it becomes hot.
- 6. Screw the lens back on.
- 7. Turn power back on at the main power supply (fuse or breaker box).
- Service
- Concernant ce guide
- Sécurité
- Mise en oeuvre
- Pièces et accessoires
- Tableau 1: Pièces et accessoires
- Brûleurs à gaz scellés
- Capuchons de brûleurs
- Grilles de brûleurs
- MAllumeur électronique
- Brûleur haute puissance
- Brûleur de précision
- Grilles plates de four
- 1. Saisir fermement la grille par les côtés.
- 2. Incliner la grille vers le haut pour mettre la butée dans le guide.
- 3. Amener la grille en position horizontale et pousser au fond. La grille doit être à plat, droite et non croche.
- Contrôle (Panneau)
- Panneau de contrôle
- Tableau 2: Panneau de contrôle du four
- La pendule
- Concernant la pendule
- Réglage de la pendule
- 1. PENDULE figure et 4 chiffres clignotent. Tourner le bouton pour choisir AM ou PM.
- 2. Presser Time. PENDULE figure et les minutes clignotent.
- 3. Tourner le bouton et régler les minutes.
- 4. Presser Time et la pendule est réglée.
- 1. Presser Time. MINUTERIE 1 clignote.
- 2. Tourner le bouton pour choisir PENDULE.
- 3. Presser Time et les heures clignotent.
- 4. Tourner le bouton pour changer les heures.
- 5. Presser Time et les minutes clignotent.
- 6. Tourner le bouton pour changer les minutes.
- 7. Presser Time et la pendule est réglée.
- Le menu de sélection de fonction
- 1. Presser et maintenir COOKING MODE (mode cuisson) pendant 5 secondes. SÉLECTION FONCTION figure.
- 2. Tourner lentement le bouton à la fonction désirée. Il y aura un léger décalage avant de voir chaque message ou fonction à l’affichage. Tourner lentement et attendre environ 1 seconde pour que figure la fonction suivante.
- 3. Presser START pour choisir la fonction.
- 4. Tourner le bouton au réglage désiré et presser MARCHE. Lorsque tous les réglages sont effectués pour la fonction, SÉLECTION FONCTION clignote de nouveau.
- 5. Presser ARRÊT pour quitter le menu sélection fonction.
- 1. Accéder au menu SÉLECTION FONCTIONS.
- 2. Tourner le bouton dans le sens horaire pour afficher VOLUME.
- 3. Presser START.
- 4. Tourner le bouton pour choisir faible, moyen ou élevé.
- 5. Presser START.
- 1. Accéder au menu SÉLECTION FONCTIONS.
- 2. Tourner le bouton dans le sens horaire pour afficher SELECT TEMP F-C.
- 3. Presser START.
- 4. Tourner le bouton pour choisir Fahrenheit (F) ou Celsius (C).
- 5. Presser START pour accepter la sélection.
- 1. Accéder au menu SÉLECTION FONCTIONS.
- 2. Tourner le bouton dans le sens horaire pour afficher AFFICH PENDULE.
- 3. Presser START.
- 4. Tourner le bouton et marche ou arrêt figure.
- 5. Presser START pour accepter la sélection.
- 1. Accéder au menu SÉLECTION FONCTIONS.
- 2. Tourner le bouton dans le sens horaire jusqu’à la langue désirée.
- 3. Presser START.
- 4. Tourner le bouton dans le sens horaire pour une autre langue.
- 5. Presser START pour accepter le changement.
- 1. Accéder au menu SÉLECTION FONCTIONS.
- 2. Tourner le bouton dans le sens horaire jusqu’à ce que TOUCHES VERR clignote.
- 3. Presser START. CLAVIER VERR figure. Il y a un bip si une touche est pressée indiquant le verrouillage.
- 4. Pour déverrouiller, presser COOKING MODE et tenir 5 secondes. TOUCHE DEVER figure.
- 5. Lorsque déverrouillé, la pendule figure de nouveau.
- 1. Accéder au menu SÉLECTION FONCTIONS.
- 2. Tourner le bouton dans le sens horaire jusqu’à ce que DEVIA TEMP FOUR figure.
- 3. Presser START. 0 ˚F figure.
- 4. Tourner le bouton pour augmenter en tranches de 25 ˚F.
- 5. Presser START pour accepter le changement.
- 1. Accéder au menu SÉLECTION FONCTIONS.
- 2. Tourner le bouton dans le sens horaire jusqu’à ce que REMISE DÉFAUT figure.
- 3. Presser START. SÉLECTION FONCTIONS figure à l’affichage.
- 1. S'assurer que le four est hors circuit.
- 2. Accéder au menu sélection fonction.
- 3. Tourner le bouton dans le sens horaire jusqu'à ce que l'option SABBAT figure.
- 4. Presser MARCHE. CUISSON figure à l'affichage et la température clignote.
- 5. Tourner le bouton pour régler la température.
- 6. Mettre l'éclairage du four en circuit si désiré (presser ÉCLAIRAGE).
- 7. Presser MARCHE. Le four se met en marche après 5 secondes.
- 1. Accéder au menu SÉLECTION FONCTIONS.
- 2. Tourner le bouton dans le sens horaire jusqu’à ce que FORMAT HEURE figure.
- 3. Presser START.
- 4. Tourner le bouton pour choisir format 12 ou 24 h.
- 5. Presser START pour accepter le choix.
- 1. Accéder au menu SELECC FUNCIONES.
- 2. Tourner le bouton dans le sens horaire jusqu’à ce que AUTO CONVECT BAKE figure.
- 3. Presser Start.
- 4. Tourner le bouton pour choisir ON ou OFF.
- 5. Presser START pour accepter le choix.
- Avant la première utilisation
- Pièces et accessoires
- Fonctionnement - surface de cuisson
- Fonctionnement - four
- Concernant le four
- Fonctionnement
- Régler le mode cuisson et la température
- 1. Presser COOKING MODE.
- 2. CUISSON figure à l’affichage.
- 3. S’il n’y a pas de changement en moins de 5 secondes, le contrôle fait un bip et clignote. Si tel est le cas, presser START.
- 4. Pour changer le mode cuisson, tourner le bouton.
- 5. Presser START.
- 6. Le mode choisi figure à l’affichage avec la température à défaut qui clignote.
- 7. Pour choisir une autre température, tourner le bouton à droite ou à gauche (en tranches de 5˚) à la température désirée.
- 8. Presser START, sinon, le four se met automatiquement en circuit en 5 secondes.
- 9. L’affichage alterne entre le mode cuisson et préchauffage.
- 10. Pour changer la température pendant la cuisson, presser température. Tourner le bouton pour choisir une autre température et presser START.
- 11. Une fois la cuisson terminée, presser OFF pour fermer le four.
- Utilisation de la minuterie
- Pour régler la minuterie:
- 1. Presser TIME et MINUTERIE 1 clignote.
- 2. Tourner le bouton pour régler les minutes. Si seules les minutes sont réglées, presser START. Autrement, passer à l’étape 4.
- HR:MIN
- TIMER
- 3. Presser TIME et les heures clignotent.
- 4. Tourner le bouton pour régler les heures.
- 5. Presser TIME de nouveau, la minuterie est réglée.
- 6. Si TIME ou START n’est pas pressée, le four émet un bip et l’affichage minuterie clignote.
- 1. Presser TIME. MINUTERIE 1 figure. Choisir MINUTERIE 1 ou 2.
- 2. Presser TIME. REMISE MIN 1 (2) figure. Les minutes clignotent.
- 3. Tourner le bouton dans un sens ou l’autre pour changer les minutes.
- 4. Presser TIME de nouveau, les heures clignotent.
- 5. Tourner le bouton dans un sens ou l’autre pour changer les heures.
- 6. Presser TIME et l’heure est réglée.
- 1. Presser TIME une fois. MINUTERIE 1 clignote.
- 2. Tourner le bouton pour choisir EFF MINUTERIE 1 ou 2. Presser TIME.
- 3. Si la touche n’est pas pressée, il y a un bip et l’affichage clignote.
- 4. Presser TIME pour revenir à l’écran principal.
- Utilisation de la cuisson différée ou minutée
- Régler un mode minuté
- 1. Presser COOKING MODE.
- 2. Cuisson figure. Tourner le bouton pour choisir un autre mode.
- 3. Presser START.
- 4. Tourner le bouton pour choisir la température.
- 5. Presser TIME. Cuisson min figure.
- 6. Presser TIME. REG CUISS MIN figure, les minutes clignotent.
- 7. Régler les minutes. Presser TIME.
- 8. Les heures clignotent. Les régler. Presser START.
- 9. CUISSON MIN figure et le four commence à préchauffer.
- 1. Suivre les étapes 1 à 5 ci-dessus.
- 2. Tourner le bouton pour afficher CUISS DIFFÉRÉE.
- 3. Presser TIME. REG CUISSON MIN figure, les minutes clignotent.
- 4. Régler les minutes et presser TIME. Les heures clignotent.
- 5. Régler les heures et presser TIME. REG FIN CUISS figure.
- 6. Presser TIME.
- 7. Utiliser le bouton pour entrer l’heure d’arrêt ou de mise hors circuit du four.
- 8. Régler les heures et presser TIME.
- 9. Régler les minutes et presser TIME.
- 10. À la fin du temps de cuisson programmé, le four se met automatiquement hors circuit. FIN CUISS MIN figure et il y a un bip. Presser OFF pour effacer.
- 1. Presser TIME.
- 2. Tourner le bouton à BAKE END ou BAKE TIME.
- 3. Presser TIME.
- Régler le mode cuisson et la température
- Pour de meilleurs résultats avec le appareil
- Nettoyage et entretien
- Nettoyage - surface de cuisson
- Nettoyage - four
- Nettoyage quotidien
- Directives de nettoyage
- Éviter ces nettoyants
- Tableau 8: Nettoyage du four
- Autonettoyage du four
- Préparation du four pour l’autonettoyage
- 1. Retirer tout ustensile et casserole.
- 2. Retirer les grilles. Si elles sont laissées dans le four pendant l’autonettoyage, elles perdront leur fini brillant et deviendront foncées. Voir le tableau nettoyage du four.
- 3. Essuyer tout déversement mou et graisse avec un essuie-tout. L’excès de graisse peut causer des flammes et de la fumée dans le four pendant l’autonettoyage.
- 4. Voir l’illustration ci-dessus. Certaines zones du four doivent être nettoyées à la main avant le cycle. Utiliser une éponge s...
- 5. S’assurer que l’éclairage est hors circuit, que les ampoules et les couvercles sont en place. Ne pas actionner le four sans les ampoules et les couvercles en place.
- 1. Presser COOKING MODE.
- 2. Tourner le bouton jusqu’à ce que AUTONETTOYANT figure. Presser START.
- 3. La durée par défaut est 4 heures. Pour changer, tourner le bouton pour changer le nombre d’heures, autrement passer à l’étape 4.
- 4. Presser START. AUTONETTOYANT clignote. Presser START.
- 5. ENLEVER GRILLE figure à l’affichage pour rappeler d’enlever les grilles.
- 6. Presser START de nouveau pour actionner l’autonettoyage.
- 1. Presser COOKING MODE.
- 2. Tourner le bouton jusqu’à ce que AUTONETTOYANT figure.
- 3. Presser START. La durée par défaut est 4 heures. Pour changer, tourner le bouton pour changer le nombre d’heures, autrement passer à l’étape 4.
- 4. Presser START.
- 5. Tourner le bouton jusqu’à ce que NETTOYA DIFFERE figure. Presser START.
- 6. FIN AUTONETTOY figure.
- 7. Tourner le bouton pour entrer l'heure du jour à laquelle l'autonettoyage s'arrête : régler les heures, presser TIME, régler les minutes.
- 8. Presser START. L’affichage indique d’enlever les grilles.
- 9. Presser START. NETTOY DIFFERE figure. L’autonettoyage commence automatiquement à l’heure réglée.
- 1. À la fin du temps programmé, le four se met automatiquement hors circuit. FIN AUTONETTOY figure. Presser OFF pour effacer.
- 2. Le mode autonettoyage peut produire de la cendre au fond du four, l’enlever avec un chiffon humide avant d’utiliser le four de nouveau.
- 3. Essuyer les bords des grilles avec de l’huile à cuisson, enlever l’excès.
- Nettoyage - tiroir
- Entretien
- Entretien du la surface
- Entretien du four
- Retrait de la porte
- 1. S’assurer de lire l’AVERTISSEMENT au dessous avant d’enlever la porte.
- 2. Ouvrir la porte complètement.
- 3. Basculer le levier de la charnière vers soi.
- 4. Fermer la porte à environ mi chemin. Arrêter lorsque l'on sent une résistance des charnières.
- 5. Tenir fermement la porte par les côtés avec les deux mains, tirer la porte droit hors des fentes de charnières. Maintenir fermement, la porte est lourde.
- 6. Placer la porte dans un endroit stable pour le nettoyage.
- 1. Tenir fermement la porte avec les deux mains. Placer les charnières dans les fentes.
- 2. Ouvrir la porte complètement pour exposer charnières et fentes. Pousser le levier (un sur chaque charnière) loin de soi (vers l’appareil).
- 3. Après avoir placer les fixations de charnières en position, fermer et ouvrir la porte lentement pour s’assurer qu’elle est correcte et bien en place.
- 4. La porte doit être droite, non croche.
- 1. Lire l’AVERTISSEMENT ci-dessus.
- 2. Mettre hors circuit à l’alimentation principale (fusible ou coupe-circuit).
- 3. Dévisser la lentille pour l’enlever.
- 4. Dévisser l’ampoule de la douille.
- 5. Remplacer l’ampoule par une nouvelle ampoule d’électroménagers 40 watts. Éviter de toucher l’ampoule avec les doigts, car les huiles de la main peuvent l’endommager lorsqu’elle devient chaude.
- 6. Visser l’ampoule.
- 7. Remettre en circuit à l’alimentation principale (fusible ou coupe-circuit)
- Service
- Acerca de este manual
- Seguridad
- Comenzar
- Partes y accesorios
- Tabla 1: Partes y accesorios
- Quemadores sellados de gas
- Tapas de quemadores
- Rejillas de quemadores
- Ignitor electrónico
- Quemador de alto poder
- Quemador de precisión
- Rejillas planas del horno
- 1. Agarre la rejilla firmemente en ambos lados.
- 2. Incline la rejilla hacia arriba para encajar el tope en el portarejillas.
- 3. Cambie la rejilla a una posición horizontal y empújela completamente. La rejilla debe estar recta y plana, no torcida.
- Panel de Control
- Panel de control del horno
- Tabla 2: Panel de control del horno
- El reloj
- Acerca del reloj
- Poner el reloj
- 1. Aparecerá RELOJ y los dígitos de la hora parpadean. Gire la perilla para seleccionar la hora y am o pm.
- 2. Oprima Time (Hora). Aún aparece RELOJ y los dígitos de minutos parpadearán.
- 3. Gire la perilla. Ajuste los minutos.
- 4. Oprima Time y el reloj queda configurado.
- 1. Oprima Time (Hora). RELOJ 1 parpadea en la pantalla.
- 2. Gire la perilla para seleccionar RELOJ.
- 3. Oprima Time y parpadean los dígitos de la hora.
- 4. Gire la perilla para cambiar las horas.
- 5. Oprima Time nuevamente y parpadearán los dígitos de minutos.
- 6. Gire la perilla para cambiar los minutos.
- 7. Oprima Time nuevamente y el reloj quedará configurado.
- El menú “Select Functions” (Seleccionar Funciones)
- 1. Oprima y mantenga oprimido el botón MODO DE CONCINAR por cinco (5) segundos. SELECC FUNCIONES aparece en la pantalla.
- 2. Gire la perilla lentamente a la opción deseada. Habrá un ligero retardo antes de poder ver cada mensaje (u opción) en la pantalla. Gire la perilla lenta- mente y espere aproximadamente un segundo para ver la siguiente opción en la pantalla.
- 3. Oprima START (Inicio) para seleccionar la función.
- 4. Gire la perilla lentamente a la opción deseada y oprima START. Cuando se hayan terminado todos los ajustes para la función, vuelve a parpadear SELECC FUNCIONES.
- 5. Oprima OFF para salirse del menú SELECC FUNCIONES.
- 1. Acceda al menú SELECC FUNCIONES.
- 2. Gire la perilla en sentido del reloj hasta que aparezca VOLUME (Volumen).
- 3. Oprima Start.
- 4. Gire la perilla para seleccionar el nivel de volumen, Bajo, Mediano o Alto.
- 5. Oprima Start.
- 1. Acceda al menú SELECC FUNCIONES.
- 2. Gire la perilla en sentido del reloj que aparezca SELECC TEMP F-C.
- 3. Oprima Start.
- 4. Gire la perilla para seleccionar grados Fahrenheit (F) o Celsio (C).
- 5. Oprima Start para aceptar la nueva seleción.
- 1. Acceda al menú SELECC FUNCIONES.
- 2. Gire la perilla en sentido del reloj hasta que aparezca PANTALLA RELOJ.
- 3. Oprima START.
- 4. Gire la perilla para seleccionar ON (Prender) o OFF (Apagar).
- 5. Oprima START para aceptar la nueva selección.
- 1. Acceda al menú SELECC FUNCIONES.
- 2. Gire la perilla en sentido del reloj hasta que aparezca el idioma deseado.
- 3. Oprima START.
- 4. Gire la perilla en sentido del reloj para seleccionar un idioma diferente.
- 5. Oprima START para aceptar el idioma nuevo.
- 1. Acceda al menú SELECC FUNCIONES.
- 2. Gire la perilla en sentido del reloj hasta que parpadee BLOQUEAR TECLAS.
- 3. Oprima Start. Aparece BLOQUEAR TECLADO. La pantalla emite un pitido cuando se oprime una tecla para indicar que el teclado está bloqueado.
- 4. Para desbloquear los teclados, oprima COOKING MODE (Modo de Cocinar) y mantenga oprimido por 5 segundos. La pantalla indicará ABRIR TECLADO.
- 5. Cuando está desbloqueado, el reloj volverá a aparecer en la pantalla.
- 1. Acceda al menú SELECC FUNCIONES.
- 2. Gire la perilla en sentido del reloj hasta que aparezca COMP HORN TEMP.
- 3. Oprima START. Aparece 0˚ F.
- 4. Gire la perilla para aumentar la temperatura en incrementos de +25˚F.
- 5. Oprima START para aceptar el cambio de la temperatura.
- 1. Acceda al menú SELECC FUNCIONES.
- 2. Gire la perilla en sentido del reloj hasta que aparezca RESTABL DEFAULT.
- 3. Oprima START. La pantalla muestra SELECC FUNCIONES.
- 1. Verifique que el horno esté apagado.
- 2. Acceda al menú SELECT FUNCTION.
- 3. Gire la perilla en sentido del reloj hasta que aparezca SABBATH OPTION.
- 4. Oprima START. La pantalla indicará BAKE (Hornear) y la temperatura empieza a parpadear.
- 5. Gire la perilla para fijar la temperatura del horno.
- 6. Prenda la luz del horno si así lo desea (oprima LIGHT) (Luz).
- 7. Oprima START. El horno comienza después de 5 segundos.
- 1. Accesa al menú SELECC FUNCIONES.
- 2. Gire la perilla en sentido del reloj hasta que aparezca TIME FORMAT.
- 3. Oprima Start.
- 4. Gire la perilla para seleccionar formato de 12 horas o 24 horas.
- 5. Oprima Start para aceptar la nueva seleción.
- 1. Accesa al menú SELECC FUNCIONES.
- 2. Gire la perilla en sentido del reloj hasta que aparezca AUTO CONVECT BAKE.
- 3. Oprima Start.
- 4. Gire la perilla para seleccionar ON o OFF.
- 5. Oprima Start para aceptar la nueva seleción.
- Antes de usar el aparato por primera vez
- Partes y accesorios
- Operación - Parrilla
- Operación - Horno
- Acerca del horno
- Operación
- Ajustar el modo de cocinar y la temperatura
- 1. Oprima COOKING MODE (Modo de Cocinar).
- 2. HORNEAR parpadea en la pantalla.
- 3. Cuando no se realiza otro ajuste dentro de 5 segundos, el control emitirá un pitido y parpadea. Cuando esto sucede, oprima START.
- 4. Gire la perilla para cambiar el modo de cocinar.
- 5. Oprima START.
- 6. El modo seleccionado aparecerá en la pantalla, junto con la temperatura de default para ese modo, la cual estará parpadeando.
- 7. Para seleccionar una temperatura diferente, gire la perilla hacia la derecha o izquierda (en incrementos de 5˚) hasta llegar a la temperatura deseada.
- 8. Oprima START. Si no oprime START, el horno se prenderá automáticamente en 5 segundos.
- 9. La pantalla alterna entre el modo de cocinar y precalentar.
- 10. Para cambiar la temperatura durante el proceso de cocinar, simplemente oprima temperature. Gire la perilla para seleccionar una temperatura nueva y oprima START.
- 11. Una vez que haya terminado el horneado, oprima OFF para apagar el horno.
- Usar el cronómetro
- Para configurar el cronómetro:
- 1. Oprima TIME y RELOJ 1 parpadea en la pantalla.
- 2. Gire la perilla para fijar los minutos. Si ajusta solamente los minutos, oprima a START. De lo contrario, siga con el paso 4.
- 3. Oprima TIME nuevamente y las horas parpadean.
- 4. Gire la perilla para fijar las horas.
- 5. Oprima TIME nuevamente. Ahora el TIMER (Reloj/Cronómetro) está configurado.
- 6. Si no oprime TIME o START, el horno comenzará a emitir pitidos y la pantalla del reloj comienza a parpadear.
- 1. Oprima TIME. RELOJ 1 aparece en la pantalla. Seleccione el RELOJ 1 o 2.
- 2. Oprima TIME. RESTABL RELOJ 1 (2) aparece en la pantalla. Los dígitos de minutos parpadean.
- 3. Gire la perilla en sentido del reloj o en sentido contrario del reloj para cambiar los minutos.
- 4. Oprima TIME nuevamente y parpadean los dígitos de las horas.
- 5. Gire la perilla en sentido del reloj o en sentido contrario del reloj para cambiar las horas.
- 6. Oprima TIME y el tiempo nuevo está configurado.
- 1. Oprima TIME una vez. RELOJ 1 parpadea.
- 2. Gire la perilla para seleccionar BORRAR RELOJ 1(2). Oprima TIME.
- 3. Si no oprime el botón de hora, el horno emitirá un pitido y la pantalla sigue parpadeando.
- 4. Oprima TIME para regresar a la pantalla principal.
- Usar el modo de cocinar cronometrado o retardado
- Configurar un modo cronometrado
- 1. Oprima COOKING MODE (Modo de Cocinar).
- 2. HORNEAR aparece en la pantalla. Para seleccionar otro modo de cocinar, gire la perilla.
- 3. Oprima START.
- 4. Gire la perilla para seleccionar la temperatura deseada.
- 5. Oprima TIME. Aparece HORNEADO CRON en la pantalla.
- 6. Oprima TIME. FIJAR HORA HORN aparece en la pantalla y los minutos parpadean.
- 7. Fije los minutos. Oprima TIME.
- 8. Las horas parpadean. Fije las horas. Oprima START.
- 9. HORNEADO CRON aparece en la pantalla y horno comienza a precalentar.
- 1. Siga los pasos 1 hasta 5 de arriba.
- 2. Gire la perilla hasta que aparezca HORNEADO RETRAS.
- 3. Oprima TIME. FIJAR HORA HORN aparece en la pantalla y los minutos parpadean.
- 4. Fije los minutos y luego oprima TIME. Las horas parpadean.
- 5. Fije las horas y luego oprima TIME. FIJAR FIN HORN aparece en la pantalla.
- 6. Oprima TIME.
- 7. Use la perilla para ingresar la hora del día cuando el horno deje de cocinar o cuando se apague.
- 8. Fije las horas y luego oprima TIME.
- 9. Fije los minutos y luego oprima TIME.
- 10. Al final del tiempo programado de cocinar, el horno se apaga automáticamente. La pantalla indicará FIJ FIN HORN (Fin del Horneado Cronometrado) y se escucharán pitidos de recordatorio. Oprima OFF para borrarlo.
- 1. Oprima TIME.
- 2. Gire la perilla a FIN HORNEAR o TIEMPO HORNEAR.
- 3. Oprima TIME.
- Ajustar el modo de cocinar y la temperatura
- Sacar el mayor provecho de su aparato
- Limpieza y Mantenimiento
- Limpieza - Parilla
- Limpieza - Horno
- Limpieza diaria
- Indicaciones para la limpieza
- Evitar estos limpiadores
- Tabla 8: Guía de limpieza del horno
- Autolimpiar el horno
- Preparar el horno para la autolimpieza
- 1. Saque todos los utensilios y moldes.
- 2. Saque las rejillas del horno. Si se dejan las rejillas en el horno durante el ciclo de la autolimpieza, perderán su acabado b...
- 3. Limpie suciedades muy grandes, restos de alimentos y grasa con toallas de papel antes de iniciar la autolimpieza del horno. Un exceso de grasa causará llamas y humo dentro del horno durante autolimpieza.
- 4. Revise la ilustración arriba. Algunas áreas del horno deben ser limpiadas a mano antes de iniciar el ciclo. Use una esponja j...
- 5. Asegúrese que las lámparas interiores del horno estén apagadas y que los focos y las cubiertas de lentes estén en sus lugares. No debe operar el horno sin que los focos y las cubiertas estén en sus lugares.
- 1. Oprima COOKING MODE (Modo de Cocinar).
- 2. Gire la perilla hasta que aparezca el modo AUTOLIMPIEZA. Oprima START.
- 3. El tiempo de limpieza por default es 4 horas. Para cambiar el tiempo de limpieza, gire la perilla para cambiar el número de horas. De otro modo, siga con el paso 4.
- 4. Oprima START. AUTOLIMPIEZA parpadea. Oprima START.
- 5. QUITAR REJILLAS aparece en la pantalla como recordatorio para quitar las rejillas del horno.
- 6. Oprima START nuevamente para iniciar la autolimpieza.
- 1. Oprima COOKING MODE (Modo de Cocinar).
- 2. Gire la perilla hasta que aparezca el modo AUTOLIMPIEZA. Oprima START.
- 3. El tiempo de limpieza por default es 4 horas. Para cambiar el tiempo de limpieza, gire la perilla para cambiar el número de horas. De otro modo, siga con el paso 4.
- 4. Oprima START.
- 5. Gire la perilla hasta que aparezca el modo LIMP RETRASADO. Oprima START.
- 6. FIN AUTOLIMPIEZ aparece en la pantalla.
- 7. Gire la perilla para ingresar la hora del día que quiere terminar la autolimpieza: Fije las horas, oprima time, fije los minutos.
- 8. Oprima START. La pantalla le va a recordar de quitar las rejillas.
- 9. Oprima START. La pantalla muestra LIMP RETRASADO. La autolimpieza se iniciará automáticamente a la hora correcta.
- 1. Al final del tiempo programado de limpieza, el horno se apagará automáticamente. FIN AUTOLIMPIEZ aparece en la pantalla. Oprima OFF para borrarlo.
- 2. El modo de autolimpieza puede producir cenizas que se asentarán dentro del horno. Cuando esto sucede, quite las cenizas con un trapo húmedo antes de usar el horno.
- 3. Limpie los bordes de las rejillas con aceite comestible para permitir un deslizamiento correcto. Limpie el exceso del aceite.
- Limpieza - Cajones
- Mantenimiento
- Mantenimiento de la parilla
- Mantenimiento del horno
- Quitar la puerta
- 1. Asegúrese de leer la ADVERTENCIA abajo antes de tratar de quitar la puerta.
- 2. Abra la puerta completamente.
- 3. Voltee la palanca en la bisagra hacia usted.
- 4. Cierre la puerta dejándola mitad abierta. Pare cuando sienta la resistencia de la bisagra.
- 5. Sosteniendo la puerta firmemente en ambos costados con ambas manos, jale la puerta y sáquela de las ranuras de las bisagras. Sostenga la puerta firmemente, ya que pesa mucho.
- 6. Coloque la puerta en un lugar conveniente y estable para su limpieza.
- 1. Sosteniendo la puerta firmemente con ambas manos, coloque las bisagras en las ranuras.
- 2. Abra la puerta completamente para exponer las bisagras y las ranuras. Empuje la palanca (una en cada bisagra) lejos de sí mismo (de vuelta hacia la estufa).
- 3. Después de regresar los soportes con bisagra a su posición, asegúrese de cerrar y abrir la puerta lentamente para estar seguro que esté colocada bien y que funcione correctamente.
- 4. La puerta debe estar recta, no torcida o chueca.
- 1. Lea la ADVERTENCIA de arriba.
- 2. Apague la corriente en la principal fuente de alimentación (caja de fusibles o interruptor).
- 3. Desatornille el lente y sáquelo.
- 4. Saque el foco de su casquillo, dándole vueltas.
- 5. Reemplace el foco por uno nuevo. Use un foco de 40 Watt aprobado para aparatos electrodomésticos. Evite tocar el foco con los dedos, ya que la grasa de las manos puede dañar el foco cuando éste se calienta.
- 6. Vuelva a atornillar el lente.
- 7. Prenda la corriente en la principal fuente de alimentación (caja de fusibles o interruptor).
- Servicio