BIONAIRE BFH3521 User Manual

Heater fan, Hold to turn off, Instruction leaflet

Advertising
background image

Step 5 – Slide the base and the locking nut onto the cord,

smooth surface facing up.
Make sure to align the dot on the back of the
base to the dot on the neck of the heater.

Step 6 – Hold base straight while tightening the locking

nut by turning clockwise.

Step 7 – Insert the power cord through the opening at the

rear of the base, twist to lock in place (see Figure
3).

Step 8 – Carefully turn the heater upright, place on a firm,

level surface.

OPERATING INSTRUCTIONS
1.

Place heater on a firm, level surface.

2.

Your heater comes assembled and ready to use in the
reduced height configuration.

3.

To use with pedestal, see Assembly Instructions.

4.

Avoid overloading your circuit by not using other high
wattage appliances in the same outlet. At 1500 Watts,
this unit draws 12.5 Amps.

NOTE: The power light will illuminate when the heater is
plugged in.

AUTO SAFETY SHUT-OFF WITH INSTANT TIP OVER
PROTECTION
This heater is equipped with a patented, technologically-
advanced safety system that requires the user to reset
the heater if there is a potential overheat situation. When
a potential overheat temperature is reached, the system
will automatically shut the heater off. It can only resume
operation when the user resets the unit.

To Reset the Heater:

If the unit shuts down, follow these steps:
1. Unplug the unit.
2. Wait 30 minutes to cool down.
3. Plug unit in and operate normally.

Tip-Over Shut-Off:

If the unit is tipped over in any direction, it will instantly shut
off. To reset, simply place the heater in an upright position.
Press the Mode/On button and it will operate normally.

TROUBLESHOOTING
If your heater fails to operate:
• UNPLUG THE UNIT
• Make sure the electrical outlet or circuit breaker is working.

Check for obstructions. If you find an obstruction turn
the heater OFF, and unplug the unit. Carefully remove
the obstruction and follow the reset instructions.

The temperature may be set too low. Adjust the
thermostat until the heater restarts.

Please DO NOT attempt to open or repair the heater.
Please see the Warranty for Service Instructions.

1 YEAR LIMITED WARRANTY
Sunbeam Products, Inc. doing business as Jarden
Consumer Solutions or if in Canada, Sunbeam
Corporation (Canada) Limited doing business as Jarden
Consumer Solutions (collectively “JCS”) warrants that for
a period of one year from the date of purchase, this
product will be free from defects in material and
workmanship. JCS, at its option, will repair or replace this
product or any component of the product found to be
defective during the warranty period. Replacement will be
made with a new or remanufactured product or
component. If the product is no longer available,
replacement may be made with a similar product of equal
or greater value. This is your exclusive warranty. Do NOT
attempt to repair or adjust any electrical or mechanical
functions on this product. Doing so will void this warranty.
This warranty is valid for the original retail purchaser from
the date of initial retail purchase and is not transferable.
Keep the original sales receipt. Proof of purchase is
required to obtain warranty performance. JCS dealers,
service centers, or retail stores selling JCS products do
not have the right to alter, modify or any way change the
terms and conditions of this warranty.
This warranty does not cover normal wear of parts or
damage resulting from any of the following: negligent use
or misuse of the product, use on improper voltage or
current, use contrary to the operating instructions,
disassembly, repair or alteration by anyone other than
JCS or an authorized JCS service center. Further, the
warranty does not cover: Acts of God, such as fire, flood,
hurricanes and tornadoes.

What are the limits on JCS’s Liability?
JCS shall not be liable for any incidental or consequential
damages caused by the breach of any express, implied
or statutory warranty or condition.
Except to the extent prohibited by applicable law, any
implied warranty or condition of merchantability or fitness
for a particular purpose is limited in duration to the
duration of the above warranty.
JCS disclaims all other warranties, conditions or
representations, express, implied, statutory or otherwise.
JCS shall not be liable for any damages of any kind
resulting from the purchase, use or misuse of, or inability
to use the product including incidental, special,
consequential or similar damages or loss of profits, or for
any breach of contract, fundamental or otherwise, or for
any claim brought against purchaser by any other party.
Some provinces, states or jurisdictions do not allow the
exclusion or limitation of incidental or consequential
damages or limitations on how long an implied warranty
lasts, so the above limitations or exclusion may not apply
to you.

This warranty gives you specific legal rights, and you may
also have other rights that vary from province to province,
state to state or jurisdiction to jurisdiction.

How to Obtain Warranty Service

In the U.S.A.
If you have any question regarding this warranty or would
like to obtain warranty service, please call 1-800-253-2764
and a convenient service center address will be provided
to you.

In Canada
If you have any question regarding this warranty or would
like to obtain warranty service, please call 1-800-253-2764
and a convenient service center address will be provided
to you.
In the U.S.A., this warranty is offered by Sunbeam
Products, Inc. doing business Jarden Consumer
Solutions located in Boca Raton, Florida 33431. In
Canada, this warranty is offered by Sunbeam Corporation
(Canada) Limited doing business as Jarden Consumer
Solutions, located at 20 B Hereford Street, Brampton,
Ontario L6Y 0M1. If you have any other problem or claim
in connection with this product, please write our
Consumer Service Department.
PLEASE DO NOT RETURN THIS PRODUCT TO ANY
OF THESE ADDRESSES OR TO THE PLACE OF
PURCHASE.

© 2008 Sunbeam Products, Inc. doing business as
Jarden Consumer Solutions. All Rights Reserved.
Distributed by Sunbeam Products, Inc. doing business as
Jarden Consumer Solutions, Boca Raton, Florida 33431.

BFH3521UM08ESM1 Printed in China

14.To prevent a possible fire, DO NOT block air intakes or

exhaust in any manner. DO NOT use on soft surfaces,
like a bed, where openings may become blocked.

15.To disconnect heater, turn controls to OFF, then remove

plug from outlet.

16.Avoid the use of an extension cord because the

extension cord may overheat and cause a risk of fire.
However, if you have to use an extension cord, the
cord shall be No. 14 AWG minimum size and rated not
less than 1875 watts.

17.If the heater will not operate, see specific instructions

on Auto Safety Shut-off.

18.DO NOT attempt to repair or adjust any electrical or

mechanical functions on this unit. Doing so will void
your warranty. The inside of the unit contains no user
serviceable parts. All servicing should be performed by
qualified personnel only.

19.Discontinue use if plug or outlet is hot. It is

recommended that the outlet be replaced if plug or
outlet is hot to touch.

PLEASE SAVE THESE
INSTRUCTIONS

CONSUMER SAFETY INFORMATION

THIS APPLIANCE HAS A POLARIZED
AC PLUG (one blade is wider than the
other). To reduce the risk of electric
shock, this plug is intended to fit in a
polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a

qualified electrician to install the proper outlet.

DO NOT ATTEMPT TO MODIFY THIS PLUG OR
DEFEAT THIS SAFETY FEATURE IN ANY WAY.

PLEASE READ AND SAVE
THESE IMPORTANT SAFETY
INSTRUCTIONS

TECHNICAL SPECIFICATIONS
• Wattage: 1500W (+5% -10%)
• Working voltage: 120V AC/60Hz

ASSEMBLY INSTRUCTIONS
Carefully remove your heater from the box. Make certain
to remove parts from both sides of the packing foam.
Please save carton for off-season storage.
This package includes:
1 - Tower Heater

HEATER SAFETY

PLEASE READ AND SAVE
THESE IMPORTANT SAFE
SAFEGUARDS

When using electrical appliances, basic safety
precautions should always be followed to reduce the risk
of fire, electric shock, and injury to persons, including the
following:
1. Read all instructions before using the appliance.
2. To avoid fire or shock hazard, plug the appliance

directly into a 120V AC electrical outlet.

3. The heater is hot when in use. To avoid burns, DO NOT

let bare skin touch hot surfaces. If provided, use
handles when moving this heater. Keep combustible
materials, such as furniture, pillows, bedding, papers,
clothes, and curtains at least 3 ft (0.9 m) from the front
of the heater and keep them away from the sides and
rear.

4. DO NOT run cord under carpeting. DO NOT cover cord

with throw rugs, runners, or the like. Arrange cord away
from traffic area and where it will not be tripped over.

5. This heater is not intended for use in bathrooms,

laundry areas and similar indoor location. NEVER locate
heater where it may fall into a bathtub or other water
container.

6. Extreme caution is necessary when any heater is used

by, or near children or invalids, and whenever the
heater is left operating and unattended.

7. Always unplug the heater when not in use.
8. When unplugging, be sure to pull by the plug and not

the cord.

9. DO NOT insert or allow foreign objects to enter any

ventilation or exhaust opening as this may cause an
electric shock or fire, or damage the heater.

10.DO NOT operate heater with a damaged cord or plug,

or after the heater malfunctions, has been dropped or
damaged in any manner. Return appliance to
manufacturer for examination, electrical or mechanical
adjustment, or repair.

11.A heater has hot and arcing or sparking parts inside.

DO NOT use it in areas where gasoline, paint, or
flammable liquids are used or stored.

12.Use appliance only for intended household use as

described in this manual. Any other use not
recommended by the manufacturer may cause fire,
electric shock, or injury to persons. The use of
attachments not recommended or sold by the
manufacturer may cause hazards.

13.DO NOT use outdoors.

1 - Pedestal Pole
1 - Remote Control
2 - AAA Batteries for Remote Control
Inserting batteries into the Remote Control:
Before operation, insert 2 “AAA” batteries (included) into
the back of the remote control.

Do not mix old and new batteries.

Do not mix alkaline, standard (carbon-zinc), or
rechargeable (nickel-cadmium) batteries.

The remote control for this unit has the capability of
operating all control panel functions. Please note this
remote control will not work through walls.
NOTE: For your convenience a remote control holder
is integrated into the heater.

Pedestal Assembly:
If you are planning on using the pedestal, start with Step 1
(Steps 1-6 see Figure 1 and Figure 2)
Step 1 – Turn the heater upside down and place on a firm,

level surface.

Step 2 – Unscrew the locking nut by turning

counterclockwise. Slide the locking nut and base
off of the power cord.

Step 3 – Slide the pedestal pole onto the cord – internal

threads first.

Step 4 – Screw the pedestal clockwise onto the (neck)

threaded end on the bottom of the heater until
you feel resistance.

3.

By pressing the Arrow Buttons (

/

),

program the heater to turn off in up to 16 hours from
the current time, in increments of 1 hour.

4.

After setting the timer, the LED display will return to
show the current room temperature.

5.

After the predetermined length of time has passed, the
heater will automatically shut off.

Set Timer to turn heater ON:

1.

While the heater is off, press and hold the Arrow
Buttons ( / ) simultaneously.

2.

By pressing the up and down buttons, program the
heater to turn on up to 16 hours in advance of current
time, in increments of 1 hour.

3.

After the preset length of time has passed, the heater
will automatically turn on at the last mode setting that
was programmed. If no program was set, the heater
will turn on Auto Mode HI Power at 75°F for a preset
time of 2 hours.

Oscillation

Press the Oscillation Button (

) to activate or stop

oscillation feature.
NOTE: Please do not manually turn the heater on the
base. It is designed to turn only by motorized oscillation.

CLEANING/MAINTENANCE
Always unplug the heater before cleaning and allow the
heater to cool down.
1. Clean the unit with a soft cloth moistened with a mild

soap solution.

2. NEVER use abrasive or flammable solvents to clean the

unit.

3. After cleaning, be sure to completely dry the unit with a

cloth or towel.

4. Store heater in a cool, dry location.
5. The manufacturer recommends that you store the unit

in its original carton.
TIP: Over time, dust may accumulate on the front grills.
This can be removed by wiping the unit with a damp
cloth.

Digital Tower

HEATER FAN

BFH3521

Read instructions before operating.

Retain for future reference.

Instruction Leaflet

INFO-LINE

If after having read this leaflet, you have any

questions or comments on your heater,

call 1-800-253-2764 in North America.

127555/9100020008876

If you have any questions regarding your product or
would like to learn more about other Bionaire

®

products,

please contact our Consumer Service Department at
1-800-253-2764 or visit our website at
www.bionaire.com.

Mode/On
Press the Mode/On button in below sequence to select
your precise comfort level, the selected setting will then
appear on LED Display:
1. OF – OFF
When the heater is plugged in, Power Light will illuminate,
the heater is at OFF Mode without heat output. Or you
may shut off the heater at any time by pressing the Off
button on remote control.
2. HI – Manual HIGH Heat
The heater will run continuously at HIGH heat.
3. LO – Manual LOW Heat
The heater will run continuously at LOW heat at reduced
wattage.
4. AH – Auto HIGH
Use Arrow Buttons ( / ) to set your desired
temperature. The LED Display will return to show the
room temperature. The heater will then cycle On and Off
to maintain the preset temperature.
5. AL – Auto LOW
Use Arrow Buttons ( / ) to set your desired
temperature. The LED Display will return to show the
room temperature. The heater will then cycle On and Off
to maintain the preset temperature.
NOTE: Please make sure the set temperature is higher
than the current room temperature.
NOTE: It is normal for the heater to cycle On and Off as
it maintains the preset temperature. To prevent the unit
from cycling, you need to raise the thermostat setting.
When the preset temperature is reached, the fan will run
for 30 seconds without heat. This cool down process
ensures an accurate and consistent temperature reading.
If you unplug the heater, you will have to reset the digital
thermostat again by following the above instructions.
NOTE: Digital thermostat has memory. The digital
thermostat will remember the previous temperature setting
after the unit has been turned off. However, if the unit is
unplugged, the digital thermostat will be reset and will no
longer remember the previous temperature setting.

Set Timer

The Digital Thermostat allows user to program the heater to turn

ON

at a preset time or turn

OFF

after a set amount of time:

Auto Off Timer:

1.

Select the mode and/or temperature you wish the
heater to run in.

2.

While the heater is running, press and hold the
Arrow Buttons ( / ) simultaneously.
Or press the Timer button (

) on the remote control

to activate Timer.

Figure 1

Figure 3

Figure 2

Heater

Neck

Pedestal Pole

Base

Locking Nut

Power Cord

Figure 4

CONTROL PANEL & REMOTE CONTROL

Mode/On

Hold to turn off

Auto Off

75

75

Mode/On

Auto Off

Hold to turn off

A. Mode/On Button
B. Oscillation Button
C. LED Display
D. Arrow Buttons

(Up/Down)

E. Off Button

(Remote Control
only)

F. Timer

Button

(Remote Control
only)

A

F

C

B

D

E

A

B

D

BFH3521-UM_08ESM1.qxd 5/9/08 11:32 AM Page 1

Advertising