Selected channel section (p. 21) – Yamaha LS9 User Manual

Page 21

Advertising
background image

Top panel

LS9-16/32 Owner’s Manual

21

2

Pa

rts and their function

⁄0

SELECTED CHANNEL section

• • • • • • • • •

In this section you can operate the most important mix
parameters for the currently selected input channel or out-
put channel.
The function of the controllers in this section will depend
on the type of channel that is selected.

1

[HA GAIN] encoder

When an INPUT/ST IN channel is selected

The encoder will adjust the gain of the internal head
amp or an external head amp device (AD8HR) con-
nected to a rear panel slot.

When any other channel is selected

The encoder will not do anything.

B

[PAN] encoder

When an INPUT/ST IN channel is selected

When a MIX channel is selected

The encoder will adjust the panning of the signal sent
to the L/R channels (or the L/C/R channels in the case
of LCR mode) of the STEREO bus. If a MIX channel
set to stereo is selected, the encoder will adjust the
output balance of the left and right channels.

When a MATRIX channel is selected

If a monaural MATRIX channel is selected, the
encoder will not do anything. If a stereo MATRIX
channel is selected, the encoder will adjust the output
balance of the left and right channels.

When a STEREO/MONO (C) channel is
selected

The encoder will not do anything for MONO (C)
channel. For a STEREO channel, the encoder will
adjust the output balance of the left and right channels.

C

[SELECTED SEND] encoder

When an INPUT/ST IN channel is selected

The encoder will adjust the send level from that chan-
nel to the currently selected bus. (For a FIXED type
bus, the encoder will switch the send on/off.)
If the send-destination bus is stereo, this encoder will
specify the panning of the signal sent to the two buses
if an odd-numbered bus is selected, or will specify the
send level if an even-numbered bus is selected.

When a MIX channel is selected

The encoder will adjust the send level from that MIX
channel to the currently selected MATRIX bus.

When a MATRIX channel is selected

The encoder will adjust the send level from the MIX
channels to the currently selected MATRIX bus.

D

[DYNAMICS 1] encoder

When an INPUT/ST IN channel is selected

The encoder will adjust the threshold of Dynamics 1
(e.g., gate).

When any other channel is selected

The encoder will adjust the threshold of the compres-
sor, etc.

E

[DYNAMICS 2] encoder

When an INPUT/ST IN channel is selected

The encoder will adjust the threshold of Dynamics 2
(e.g., compressor).

When any other channel is selected

The encoder will not do anything.

F

EQ [Q] encoder

G

EQ [FREQUENCY] encoder

H

EQ [GAIN] encoder

These encoders adjust the Q, frequency, and gain of the
band selected by keys

9–L.

1

2

4

5

9

J

K

L

3

7

M

8

6

• The PAD will be internally switched on or off when the HA

gain is adjusted between -14 dB and -13 dB. Keep in mind
that noise may be generated if there is a difference between
the Hot and Cold output impedance of the external device
connected to the INPUT connector when using phantom
power.

NOTE

• In SENDS ON FADER mode, this encoder will not do any-

thing regardless of which channel is selected.

NOTE

• By simultaneously pressing the EQ [Q] encoder and the EQ

[GAIN] encoder, you can reset the gain to 0 dB for the band
selected by the keys below (

9

L

).

• If you have selected a LOW band or HIGH band whose type can

be changed, you can switch the type by turning the EQ [Q]
encoder while pressing it when Q is set to the maximum or mini-
mum value.

LOW band :

• Switches to LOW shelving if you turn the encoder toward the

right while pressing it when Q is at the minimum value

• Switches to high pass filter if you turn the encoder toward the

left while pressing it when Q is at the maximum value (MIX,
MATRIX, STEREO, and MONO channels only)

HIGH band :

• Switches to HIGH shelving if you turn the encoder toward the

right while pressing it when Q is at the minimum value

• Switches to low pass filter if you turn the encoder toward the

left while pressing it when Q is at the maximum value

For shelving, high pass filter, and low pass filter as well, you can
switch the type by turning the encoder while pressing it.

HINT

Advertising