Yamaha LS9 User Manual

Page 87

Advertising
background image

87

Operations in the SELECTED CHANNEL section

7

Oper

ations in the SELECTED CHANNEL section

LS9-16/32 Owner’s Manual

Making dynamics settings

To operate the dynamics of the currently selected channel,
use the SELECTED CHANNEL section [DYNAMICS 1]/
[DYNAMICS 2] encoder, and the DYNA1/DYNA2 field
of the SELECTED CH VIEW screen.

The DYNA1/DYNA2 field of the SELECTED CH VIEW
screen contains the following items.

1

DYNA1/DYNA2 popup buttons

These buttons access the DYNAMICS 1/DYNAMICS 2
popup window, where you can make detailed settings for
dynamics.

B

THRESH knob

This indicates the setting of the threshold parameter of a
gate or compressor. To adjust the value, use the
SELECTED CHANNEL section [DYNAMICS 1]/
[DYNAMICS 2] encoder. (Alternatively, move the cursor
to the knob and operate the dial or the [DEC]/[INC] keys.)

C

DYNAMICS ON/OFF button

These buttons turn dynamics processors 1/2 on/off.

D

OVER indicator

This will light if the output level of the dynamics reaches
the overload point.

E

Level meter

This displays a bar graph indication of the signal level
being input to the dynamics (on=green, off=gray) and the
amount of gain reduction (orange). The threshold setting
is shown as a vertical line.

F

Parameter knobs

These knobs indicate the values of parameters other than
threshold.

To operate the dynamics, turn the DYNAMICS ON/OFF
button on, and use the SELECTED CHANNEL section
[DYNAMICS 1]/[DYNAMICS 2] encoders to adjust the
threshold parameters. (Alternatively, move the cursor to
the DYNA1/DYNA2 field, and operate the dial or the
[DEC]/[INC] keys.)

To make detailed dynamics settings, move the cursor to
the DYNA1/DYNA2 popup button or the DYNA1/
DYNA2 field, and press the [ENTER] key to access the
DYNAMICS 1/DYNAMICS 2 popup window. (For
details on the popup window

→ p. 117)

Making HPF/EQ settings

To operate the HPF/EQ of the currently selected channel,
use the SELECTED CHANNEL section EQ encoders,
and the EQ field of the SELECTED CH VIEW screen.
The EQ field of the SELECTED CH VIEW screen con-
tains the following items.

1

EQ popup button

This button accesses the ATT/HPF/EQ popup window,
where you can make detailed HPF/EQ settings.

B

EQ ON/OFF button

Switches the EQ on/off.

C

HPF ON/OFF button

Switches the HPF on/off.

D

HPF FREQ knob

Indicates the cutoff frequency of the HPF.

E

OVER indicator

This will light when the post-EQ signal reaches the over-
load point.

F

Q/F/G knobs

These knobs indicate the Q, F (center frequency), and G
(amount of boost/cut) settings for each band (LOW, L-
MID, H-MID, and HIGH).

To operate the EQ, switch the EQ ON/OFF button on, and
use the EQ [Q], EQ [FREQUENCY], and EQ [GAIN]
knobs of the SELECTED CHANNEL section to adjust the
Q, center frequency, and the amount of boost/cut. (Use the
EQ [HIGH], EQ [HIGH MID], EQ [LOW MID], and EQ
[LOW] keys to select the band you want to operate.)
Alternatively, move the cursor to the knobs of the EQ field
in the screen, and use the dial or the [DEC]/[INC] keys.

To make detailed EQ settings, move the cursor to the EQ
popup button or the knobs of the EQ field, and press the
[ENTER] key to access the ATT/HPF/EQ popup window.
(For details on the popup window

→ p. 115)

• The DYNA 2 field of the SELECTED CH VIEW screen and the

[DYNAMICS 2] encoder of the SELECTED CHANNEL section are
valid only if an input channel is selected.

NOTE

2

1

3

4

6

5

• If you’ve turned on POPUP APPEARS WHEN PRESSING

KNOBS in the PREFERENCE popup window (

p. 194), you can

also access the above popup window by pressing the SELECTED
CHANNEL section [DYNAMICS 1]/[DYNAMICS 2] encoder.

HINT

6

2

5

1

4

3

Advertising