Installation requirements and handling, Temperature and humidity conditions, Power supply requirements – Canon ImageCLASS MF4570DN User Manual

Page 17: Installation requirements, Installation space, Important

Advertising
background image

xi

Installation Requirements and Handling

In order to use this machine in a safe and trouble-free manner, install the machine in a place that fulfills the following conditions.
Also, read the remarks carefully.

Temperature and Humidity Conditions

• Temperature range: 50 to 86°F (10 to 30°C)
• Humidity range: 20 to 80 % RH (no condensation)

IMPORTANT

Protecting the machine from condensation

• To prevent condensation from forming inside the machine

in the following cases, let the machine adjust to the
ambient temperature and humidity for at least two hours
before use.

- When the room where the machine is installed is heated

rapidly

- When the machine is moved from a cool or dry location

to a hot or humid location

• If water droplets (condensation) form inside the machine,

this can result in paper jams or poor print quality.

When using an ultrasonic humidifier

When you are using an ultrasonic humidifier, it is therefore
recommended that you use purified water or other water that
is free of impurities.
If you use tap water or well water, impurities in the water will
be dispersed through the air. This can be trapped inside the
machine, causing degradation in print quality.

Power Supply Requirements

120 to 127 V, 60 Hz

IMPORTANT

Precautions when connecting the power cord

• Do not connect this machine to an uninterruptible power

source.

• Use an AC power outlet exclusively for the machine. Do not

use the other sockets of the AC power outlet.

• Do not plug the power plug into the auxiliary outlet on a

computer.
Do not use the same AC power outlet for both the machine
and any of the following equipment.

- Copy machine

- Air conditioner

- Shredder

- Equipment that consumes a large amount of electricity

- Equipment that generates electrical noise

• When unplugging the power cord, keep interval of 5

seconds or more before plugging it again.

Miscellaneous precautions

• The maximum power consumption of the machine is

1,090 W or less.

• Electrical noise or a dramatic drop in supplied voltage may

cause the machine or computer to operate incorrectly or
lose data.

Installation Requirements

• A location with sufficient space
• A location with good ventilation
• A location with a flat, even surface
• A location able to fully support the weight of the machine

IMPORTANT

Do not install the machine in the following locations, as
this may result in damage to the machine.

• A location subject to dramatic changes in temperature or

humidity

• A location subject to condensation
• A poorly ventilated location

(If you use the machine for a long time or to perform a large
amount of printing in a poorly ventilated room, the ozone
or other odors generated by the machine may create an
uncomfortable working environment. In addition, chemical
particles are dispersed during printing; therefore, it is
important to provide adequate ventilation.)

• A location near equipment that generates magnetic or

electromagnetic waves

• A laboratory or location where chemical reactions occur
• A location exposed to salt air, corrosive gases, or toxic gases
• A location, such as on a carpet or mat, that may warp from

the weight of the machine or where the machine is liable
to sink.

Installation Space

Required installation space

MF4570dn

31 5/8" (804 mm)

4" (100 mm)

4" (100 mm)

4"

(100 mm)

4"

(100 mm)

24 1/4"

(617 mm)

29"

(735 mm)

4" (100 mm)

Paper

cassette

Feeder
cover

MF4450

30 7/8" (783.1 mm)

4" (100 mm)

24 1/4

"

(616.2 mm)

4" (100 mm)

4" (100 mm)

29"

(734.7 mm)

4"

(100 mm)

4"

(100 mm)

Feeder
cover

Paper

cassette

Advertising
This manual is related to the following products: