Two Brothers Racing 2007-08 Suzuki GSX-R1000 User Manual

V.a.l.e, Juice box™ - fuel controller

Advertising
background image

Two Brothers Racing

Juice Box™ - Fuel Controller

2007-08 Suzuki GSX-R1000 Installation & Operation Manual

Part # 008-178C

Parts Incuded

Installation Instructions

Qty.

Description

Part Number

1

Juice Box™ Fuel Control Kit

008-178C

(#9140065C)

3

Zip Ties

1

Adhesive Velcro Square

V.A.L.E.

V a r i a b l e a x i s l o c k i n g e x h a u s t

TM

Route the JUICE BOX™ harness between the steering

stem and the right fork tube. Remove the bolt securing the

harness guide bracket and route the JUICE BOX™ harness

through the harness guide bracket and down the right side

of the air box to the lower fuel injection rail. (Fig 4)

Disconnect the LOWER injector connectors from the

LOWER injectors. Connect the JUICE BOX™ female

and male connectors to the injectors and the injector

connectors that were just disconnected. Do NOT connect

the JUICE BOX™ to the upper injector connectors. (Fig 5)

Route the JUICE BOX™ ground lead (black wire) to the

battery and connect to the negative ground lug on the battery.

Start the bike. The green LED should scroll left to right and

back for about 3-5 seconds and then go to 1-2 steady or

slowly flashing green LED’s. If the number 1 green LED

and number 8 red LED’s continue flashing after startup

or idling, an injector wiring error is indicated. Re-check

the wires from the JUICE BOX™ and make sure they are

connected to the proper wire of your bike’s stock harness.

MAKE SURE you have the correct wires selected in

the stock harness. DO NOT PROCEED UNLESS ABOVE

CONDITIONS ARE MET.

Bike reassembly is opposite of disassembly.

NOTE: Re check your wire routing and JUICE BOX™

location and make certain that in no way the wires can

come into contact with any moving parts or high heat

source and that the JUICE BOX™ is mounted in a way as

to not cause a handling problem with the machine.

7.

8.

9.

10.

11.

12.

IMPORTANT - PLEASE READ CAREFULLY

Warranty

two brothers racing warrants that this product carries a warranty for 2 years from date of purchase against original

defects in materials and workmanship. should this product fail to perform for either of the above reasons, two brothers

racing will repair or replace it with an equivalent product at no charge, except for postage, to the original retail purchaser.

to obtain the benefits of this warranty, the retail purchaser must return the product and proof of purchase to the place of

original purchase.

We recommend that this performance part be installed by a qualified motorcycle
technician. If you have any doubts as to your ability to install this performance part,
please consult with your local motorcycle dealer. Read all instructions first before
starting installation. Make sure the vehicle and exhaust system are completely cool
before starting the installation. Also, make sure the vehicle is secure during installation.
Be sure to save all stock components for possible use later.

This Juice Box is legal for use on Emissions Controlled street and highway vehicles.
The Juice Box™ is not applicable, nor inteded for use on aircraft.

Thank you for purchasing a genuine Two Brothers Racing

JUICE BOX™. This product represents a radical step

forward in tuning fuel-injected motorcycles and ATVs for

optimal performance using “load-based” technology.

We at Two Brothers Racing hope that you will find this

development as exciting and useful as we do. And

remember: Proper Fuel = Maximum Power!

Make sure the vehicle is completely cool before starting

the installation. Also, make sure the vehicle is secure and

will not roll around.

Remove the two bolts that secure the front seat and tank

side panels. (Fig 1)

Remove the front seat. Remove the tank side panels by

holding the rear of the panel and gently pulling out and back.

Remove the bolt that secures the front of the tank near

the steering stem.

Remove the rear seat and get the tank stand from the rear

seat compartment. Gently lift the tank and prop it up with

the tank stand. (Fig 2)

Attach the adhesive backed hook and loop material to the

back of the JUICE BOX™ and the front sub-frame below

the instrument cluster. (Fig 3)

1.

2.

3.

4.

5.

6.

Continued on page 2

Fig 1

Fig 4

Fig 2

Fig 3

Fig 5

Advertising