Craftsman 315.114073 - Manual (Page 3)

GENERAL SAFETY RULES
WARNING! READ AND UNDERSTAND ALL
INSTRUCTIONS. Failure to follow all Instructions
listed below, may result In electric shock, fire and/or
serious personal injury.
READ ALL INSTRUCTIONS
■ Know your worklight. Read operator's manual
carefully. Learn its applications and limitations as well
as the specific potential hazards related to this light.
■ Use only recommended battery pack with your
worklight. Any attempt to use another battery pack
wilt cause damage to your worklight and could possibly
explode, cause a fire, or personal injury.
■ Use battery only with charger fisted.
MODEL
315.114073
BATTERY PACK
130279003
130279005
(Item No. 911375)
CHARGER
Model No.1425301
(Item No. 911041)
Model No. 315.115730
(item No. 140301003)
Model No. 315.115720
(Item No. 140301001)
Remove battery pack from worklight before replac­
ing bulb or performing any routine maintenance or
cleaning.
Do not disassemble your worklight.
Do not place worklight or battery pack near fire or
heat.
They may explode. Also, do not dispose of a
worn out battery pack by incinerating. Do not inciner­
ate the battery, even if it is severely damaged or com­
pletely worn out. The battery may explode in fire.
Do not store your worklight in a damp or wet
location. Do not store in locations where the
temperature is less than 50°F or more than 100°F.
Do not store in outside sheds or in vehicles.
Do not permit children to use worklight unsuper­
vised. It is not a toy. The temperature of the bulb will
become hot after being on for only a short period of
time. This hot temperature can cause bum injury if
touched and can create sufficient heat to melt some
fabrics.
If wrapped or in contact with fabrics, the worklight
lens can produce sufficient heat to melt some
fabrics. To avoid serious personal injury, never allow
the worklight lens to come in contact with anything.
Keep work area clean. Cluttered areas and benches
invite accidents.
■ Avoid dangerous environments.
■ Keep light dry, clean, and free from oil and grease.
Always use a clean cloth when cleaning. Never use
brake fluids, gasoline, petroleum-based products or
any strong solvent to clean your worklight.
■ Stay alert. Watch what you are doing and use
common sense. Do not rush.
■ Check damaged parts. Before further use of this
worklight, a part that is damaged should be carefully
checked to determine that it will operate properly and
perform its intended function. Do not use worklight if it
does not function properly.
■ Don’t expose worklight to rain. Water entering a
power tool will increase the risk of electric shock or
malfunction.
■ Stay alert, watch what you are doing and use
common sense when operating a worklight. Do not
use tool while tired or under the influence of drugs,
aicohot, or medication. A moment of inattention while
operating power tools may result in serious personal
injury.
■ Do not overreach. Keep proper footing and balance
at all times. Proper footing and balance enable better
control of the tool in unexpected situations. Do not use
on a ladder or unstable support,
WORKLIGHT USE AND CARE
■ Check for alignment of moving parts, binding of
moving parts, mounting, and any other conditions
that may affect its operation. A part that is dam­
aged should be properly repaired or replaced by
an authorized service center.
Following this ruie will
reduce the risk of shock, fire, or serious injury.
■ Store worklight out of the reach of children and
other untrained persons. Tools are dangerous in the
hands of untrained users.
SERVICE
■ Tool service must be performed only by qualified
repair personnel. Service or maintenance performed
by unqualified personnel may result in a risk of injury.
■ When servicing a tool, use only identical replace­
ment parts. Follow instructions in the Maintenance
section of this manual. Use of unauthorized parts or
failure to follow Maintenance Instructions may create a
risk of shock or injury.