Add engine oil, To turn on washer, To start the engine – Craftsman 580.751781 User Manual
Page 12: To start engine to turn on washer, Operation
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
OPERATION
NOTE; When adding oii to the engine crankcase in the
future, use only higti quality detergent oil rated with API
service classification SC, SD, SE, SF, SG rated SAE 30
weight. Use no special additives. Select the oil’s viscosity
grade according to your expected operating temperature.
colder
32°F
warmer
5W30
SAE30
Although multi-viscosity oils (5W30,10W30, etc.) improve
starting in cold weather, these multi-viscosity oils will result
in increased oil consumption when used above 32°F.
Check your engine oil level more frequently to avoid possi
ble damage from running low on oil. Oil sump capacity is
21 ounces,
ADD ENGINE OIL;
CAUTION: ANY ATTEMPT TO CRANK OR START
THE ENGINE BEFORE IT HAS BEEN PROPERLY
SERVICED WITH THE RECOMMENDED OIL RE
SULTS IN AN ENGINE FAILURE.
Place pressure washer on a level surface and remove
one of yellow Oil Fill Caps (Fig. 18), insert clean funnel
in opening, and add engine oil from the enclosed bottle
until level is at point of overflowing. Check engine oii
level before starting each time thereafter. If oil level is
below point of overflowing, fill to proper level. Crank
case oil capacity is about 620ml or 21 fluid ounces.
ADD GASOLINE:
CAUTION: DO NOT OVERFILL THE FUEL TANK.
ALWAYS ALLOW ROOM FOR FUEL EXPANSION.
WARNING: NEVER FILL FUEL TANK INDOORS.
NEVER FILL RJEL TANK WHEN ENGINE IS RUN
NING OR HOT. DO NOT LIGHT A CIGARETTE OR
SMOKE WHEN FILLING FUEL TANK.
TO SEPARATION AND FORMATION OF ACIDS DURING
STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYS
TEM OF AN ENGINE WHILE IN STORAGE. TO AVOID
ENGINE PROBLEMS, THE FUEL SYSTEM SHOULD BE
EMPTIED
BEFORE
STORAGE
OF
30
DAYS
OR
LONGER. SEE “STORAGE” ON PAGE 17. NEVER USE
ENGINE OR CARBURETOR CLEANER PRODUCTS IN
THE FUEL TANK OR PERMANENT DAMAGE MAY OC
CUR.
o Clean area around fuel fill cap, remove cap,
o Add “UNLEADED" regular gasoline, slowly, to fuel
tank,
«• Install fuel cap and wipe up any spilled gasoline.
TO TURN ON WASHER
0
Attach one end of a garden hose to a cold water source.
Water supply should not exceed 140°F (55°C).
o Check that high pressure hose is attached to pump
outlet and that water supply is attached to pump inlet.
o Turn ON water,
a Press trigger on gun and wand assembly to force air
from high pressure hose,
a Start engine according to ‘TO START THE ENGINE."
TO START THE ENGINE
IMPORTANT; DO NOT RUN PUMP WITHOUT THE
WATER SUPPLY CONNECTED AND TURNED ON
a Start, store and fuel the unit in a level position,
a Open fuel shut-off valve,
a Press trigger on pressure washer wand to relieve high
pressure and/or purge the inlet hose of air.
a Adjust safety latch on spray gun to the ON position.
This disables the trigger so you cannot inadvertently
actuate a high pressure spray (Fig, 19).
a Use regular UNLEADED gasoline with the pressure
washer engine. Regular leaded gasoline may also be
used if UNLEADED is not available. Fuel tank capacity
is 4 U.S. gallons.
IMPORTANT: IT IS IMPORTANT TO PREVENT GUM
DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYS
TEM PARTS SUCH AS THE CARBURETOR, FUEL FIL
TER, FUEL HOSE OR TANK DURING STORAGE. ALSO,
EXPERIENCE
INDICATES
THAT
ALCOHOL-BLENDED
FUELS (CALLED GASOHOL OR USING ETHANOL OR
METHANOL) CAN ATTRACTMOISTURE WHICH LEADS
Locate the Run/Stop switch (Fig, 20 on Page 13) next
to the engine cylinder head and set it to RUN,
Close the choke to FULL position (Fig. 21 on Page 13)
by sliding it to far position in direction indicated by arrow
on air cleaner housing.
Turn pressure control knob counterclockwise, two
turns from maximum pressure.
12