Nikon LS-10 Installation Guide for Macintosh User Manual
Nikon
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
Advertising
Table of contents
Document Outline
- C/D
- Nikon
- FCC Radío Frequency Interference Statement for Coolscan
- Installation Safety Regulation of Coolscan Internal Model
- AC Line Cord
- When Taking this Product Out of the Country
- Apple Disclaimer
- Acknowledgments
- Trademark Information
- Table of Contents
- Before You Begin
- About this Manual
- Unpacking
- Registration
- Software Installation
- Minimum Macintosh System Requirements
- Suggested System Configurations
- The Front Panel
- The Rear Panel - LS-10E
- The Rear Panel - LS-10
- Orientation and Pincement of the LS-10E
- Transporting Coolscan
- Connecting AC Power to the LS-10E
- Safety Precautions When Connecting AC Power to the LS-10E
- AC Power Safety Precautions - LS-10E
- Installation Precautions
- General Safety Precautions
- Operational Pre<autions
- System Requirements for SCSI Installation
- Setting the SCSI ID
- Terminating the SCSI Chain
- SCSI Cables
- The Macintosh's External SCSI Connector
- o
- The Macintosh's Internal SCSI Connector
- The SCSI Chain
- Setting Up the SCSI Chain - LS-10E
- Setting Up the SCSI Chain - LS*10
- Important Information About the SCSI Interface
- Introduction
- Film
- Slide Mounts
- Handling the Film
- Finding the Emulsion Side of the Film
- Slide Orientation
- Inserting Slides
- Ejecting Slides
- The Film Strip Holder
- Focus
- Calibration
- #1 Support Call for Coolscan. Important information for using the fiim strip holder.
- Problem: Slide fell in scanner.
- Problem: Scan has cyan or green and yellow tint. Color balance is poor, or getting colored lines through image.
- Problem: No image appears when scanning using the film strip holder.
- Problem: Scanner is not being found on SCSI bus, scanner software says "no scanner connected."
- Problem: When performing a high resolution scan in Photoshop, the resulting image has lines through it or 'dropped' pixels.
- • Problem: The scanner is not found by the Nikon Scanner plug-in.
- • Problem: The plug-in fails to find the scanner when I click Find Device.
- • Problem: I lan't find the Nikon Scanner plug-in in my third-party application
- software.
- • Problem: When I try to scan negative film on Coolscan I get an error 32208.
- • Problem: After installing the scanner, my Macintosh is displaying the flashing question mark when I start up.
- • Problem: I can't get the software installation to finish.
- • Prohlem: My Centris 610/650/660AV or Quadra 800/840AV 'hangs' at the
- completion of a scan.
- • Probiem: I can't open TIFF files created by Coolscan Control in other
- applications.
- • Problem: If I open SCSI Probe or other software that lists SCSI devices while
- scanning in Photoshop 2.5, the scan stops.
- Problem: The wat<h cursor keeps turning at the end of acquiring an image and the image never appears. Computer seems 'locked up' and system needs to be rebooted.
- • Problem: When I attempt to run the Nikon Scanner plug-in software through Fractal Design Painter I can't activate any buttons.
- Problem: Getting "Error -32008" when either previewing or scanning.
- Problem: Getting "Error type 1" or "Error code 108: Not enough memory" when scanning with Nikon Control.
- Problem: "Error -21000" when previewing or scanning.
- Problem: System won't start properly after scanner Is connected (see flashing disk w/question mark).
- Causes:
- Solutions:
- Problem: Lines or dark bands through image, scan is slow or crashes system.
- Problem: Scanning is too slow.
- Problem: TIFF files created by Coolscan Control cause "parse errors" in other software when trying to open file.
- Problem: Missing scanning Focus command in Tools dialog of Nikon software.
- »de -32003" or "-32207".
- Problem: Software reports SCSI errors.
- Problem: Cursor in Nikon software driver is square and has a '<otton-like' texture to it.
- #1 Support Call for Coolscan. Important information for using the fiim strip holder.