Attwood All-Round Globe Style Fold-Down Lights with Turning Knob Adjustment - Manual

All-Round Light
5120 Series Frosted Globe & 5350 Series
Anti-Glare Fold-Down and Fixed Base Lights
Installation Instructions
SAVE THESE INSTRUCTIONS
Form Number 69413 Rev. B 04-12
3
®
© 2004 Attwood Corporation
1016 N. Monroe Street, Lowell, MI 49331-0260 www.attwoodmarine.com
Lights meet USCG CFR 183.810, ABYC A-16 requirements, and all applicable
standards as tested by Immana Labs, 12/20/02 (Series 5100) and 7/19/02 (Series
5300). 2 Nautical Mile visibility. Use Lamp 9235, #906 13V, 6 Candle Power.
CAUTION
Read all instructions carefully before installing and using this product. All positive
(+12V DC) lighting wires require a 1-amp fuse to protect circuits and vessel. The
aluminum light pole is not grounded. MAKE SURE POWER SOURCE IS 12-VOLT
DC ONLY. HIGHER VOLTAGE WILL DAMAGE LIGHT AND CIRCUITRY.
WARNING
To prevent injury, disconnect power when installing or servicing this product.
Remove boat from water before using 120V power tools.
REQUIRED FOR INSTALLATION
• Cordless drill; 1/8" and 3/8" (3 and 10mm) bits
• Marine-grade non-silicone sealant
• Phillips screwdriver
• Two #10 pan head stainless steel screws
• 3-position switch (OFF/ON/ON)
• Fuse holder and fuse: 1-amp
• 16-gauge wire
• Appropriate marine-grade wire connectors
MOUNTING LOCATION
Frosted Globe All-Round Lights are designed for boats up to 39.4 feet (12m).
Position the All-Round Light so its bulb is not less than one meter (39.4") above
sidelights (Figure 1). If replacing an existing pole light, replace with a pole at
least as long as the existing pole.
Anti-Glare All-Round Lights are designed for boats up to 39.4 feet (12m). It
provides 360 degree controlled light output and 2-mile visibility while shielding
the driver from on-board glare (Figure 1). Position the All-Round Light so its
bulb is not less than one meter (39.4") above sidelights. If replacing an existing
pole light, replace with a pole at least as long as the existing pole.
Mount the anti-glare light in a position so that:
• Light output is flat and parallel to water when boat is floating.
• Light shines 360
°
, unobstructed.
• Light does not shine on operator, or reflect off any part of the boat in the
operator’s field of vision.
INSTALLATION INSTRUCTIONS
Bases are available for mounting on vertical or horizontal surfaces. Release
the cam-lock adjustment handle to fold light or adjust to vertical position.
Change Base Type (If Required) on Fold-Down Base
Packaged versions of the light are shipped with the horizontal base installed.
To switch to the vertical base:
1. Carefully remove the cam-lock screw and oblong washer. Set aside for
reinstallation (Figure 2).
2. Pivot the base axle out of its socket. Note position of the 2 wires in the base
slot. Remove the horizontal base.
3. Insert wires through slot of the vertical base. Reassemble in reverse order.
Mark Position for Fixed Base Light, (Figure 3)
1. Place light in selected position.
2. Using the base as a template, mark the two
mounting hole locations and one wire access hole.
Proceed to “Install Light” below.
Mark Position for Fold-Down Light
1. Release cam-lock adjustment handle and adjust
light to vertical position. (Figure 4)
2. Place light in selected position.
3. Use optional adaptors, if necessary, to allow installation on angled windshields.
4. Using the base as a template, mark the two mounting hole locations and
one wire access hole. (Figure 5) Proceed to “Install Light” below.
Install Light
CAUTION
Position wire access hole carefully, especially on aluminum boats, so that wires
do not contact the hull.
1. Remove light from marked position. Drill two 1/8" (3mm) pilot holes for
#10 screws. Drill one 3/8" (10mm) wire access hole.
2. Bring the two 16-gauge wires up through access hole.
3. Use marine-grade waterproof crimp connectors to connect gray wire to
positive lead from 3-position switch. Connect (-) negative source to black
wire and route to (-) negative terminal on battery.
4. Fasten light to deck with two #10 stainless steel pan head screws. DO
NOT OVERTIGHTEN.
Replacing Bulb
1. Unscrew lens counter-clockwise and remove. Pull bulb straight up.
2. Replace with #906 9-Watt Wedge Base Replacement Bulb (Attwood 9235-7)
available in marine, auto, and convenience stores.
3. Screw lens clockwise onto pole.
4. If lens requires replacement, order Attwood #91017B for Frosted Globe
Lights and #912852 for Anti-Glare Lights(Figure 6).
Clean the light with a mild soap and
warm water solution. Never use solvents
or abrasives that may damage the lens
or housing of the light.
This product carries the standard Attwood one-year warranty.
See www.attwoodmarine.com or Product Catalog for details.
Figure 2
Cam-lock Screw
and Oblong Washer Horizontal
Base Vertical
Base
Feed Wires Thru
Axle
Socket
STEP 1 STEP 2 STEP 3
Figure 1
One meter
or 39-3/8"
Figure 4
Locked
Unlocked
Horizontal Mount
Optional
Adaptor
Figure 5
Locked
Unlocked
Vertical Mount
Optional
Adaptor
Figure 6
Figure 3
Anti-Glare
#912852 Frosted Globe
#91017B