Symtech Gold Series Kit User Manual

Safety and health warnings, Safety by design

Advertising
background image

BRIGHT SOLUTIONS

Gold Series

HEADLAMP Resurfacer / Protector


Thank you for purchasing BRIGHT SOLUTIONS, Gold Series
this is a 3 or 4 STEP process that takes approximately 10~15

MINUTES to perform per headlamp dependent upon severity of
damage of lamp lens. By applying the patented Preserver, your

headlamp restoration will be preserved for more than two years.




KEEP OUT OF THE REACH OF CHILDREN

DO NOT ALLOW PRODUCT TO FREEZE

WHEN APPLYING PRODUCT IN TEMPERATURES

BELOW 60

o

, TURN LAMPS ON UNTIL WARM.

DO NOT APPLY SHINE RESTORER/ PROTECTOR IN

DIRECT SUNLIGHT

READ INSTRUCTIONS IN ENTIRETY BEFORE USE.

USE GLOVES TO PROTECT HANDS.

RECOMMENDED

524 S.E. Transport Drive

Lee’s Summit, Missouri 64081

816-525-9263 FAX: 816-525-9383

www.symtechcorp.net

Safety by Design

SAFETY and HEALTH

WARNINGS

ALL PRODUCTS INCLUDED IN THIS KIT ARE ON

REVERSE SIDE

A

s with any repair versus replacement, some items will not

achieve like new results. If directions are followed, significant
improvement in the appearance of the items will be achieved. As

we are unable to supervise the application process, user assumes all
risks. The manufacturer and its distributors are not liable for any

damages incurred by the use of this product. If you are unsure as
to the application process or compatibility of the item you would

like to resurface, please contact the manufacturer or distributor for
advice on how to proceed.

Can Be Used on

: Headlamps

Taillights

Turn Signal Lights

Reflective Lens Covers

FIRST

determine the extent of damage that has occurred over time to

your headlamp lens.

IF

Headlamp lens is slightly fogged and or yellowed, without

visible hairline scratches or crazing, in most cases, the lamp
can be simply cleaned clear without the use of sandpaper.

Steps 1, 3 and 4

IF

Headlamp lens has extensive yellowing, scratches, crazing
and/or pits, sanding is necessary to obtain a successful
result. Regardless of damage, using sandpaper during
cleaning will speed the process dramatically.

Steps 1, 2 ,3

STEP 1

CLEANING


Select a paper shop towel and fold in quarters (1).

Thoroughly shake the

BRIGHT SOLUTIONS Pretreatment

before applying to towel.

Open the specially formulated

BRIGHT SOLUTIONS

Pretreatment, saturate the towel (2), and begin cleaning the
entire lens with a circular motion (3).

Continue cleaning, changing the towel surface and adding more

Pretreatment as towel becomes discolored (4) with dirt and
oxidation film of lamp lens.

When dirt and discoloring ceases to be removed from lens, Proceed to

STEP 2 or 3

.

STEP 2
SANDING

Fill a container, or spray bottle with water (5), start with 1500 grit

sandpaper, dampen with water and begin sanding the entire
surface of the lens, wetting sandpaper (6), or lens as needed to
prevent buildup of particles. Sanding is complete when lamp
lens is uniform in appearance.

Note: ALWAYS sand in a straight motion (7), DO NOT use

a circular motion.

Continue sanding until all discolored plastic has been removed from

lamp surface and residue of sanding is white in appearance.

Take the 2000 grit sandpaper, dampen with water and sand the entire

surface of the lens, wetting sandpaper (6) as needed. This
process will reduce the sanding lines .

Note: ALWAYS sand in the same direction as previous step

and in a straight motion (7), DO NOT use a circular
motion.

STEP 4

SHINE RESTORER/PRESERVER

Select a LINT-FREE paper shop towel and fold in quarters (1).

NOTE:

Apply SHINE RESTORER/ PROTECTOR out

of direct sunlight. WHEN APPLYING PRODUCT
IN TEMPERATURES BELOW 60

o

, TURN LAMPS

ON UNTIL WARM

Apply a liberal amount of the SHINE RESTORER/

PROTECTOR to a clean lint-free paper towel (8) and apply it
smoothly across the plastic surface (9), avoiding runs and
bubbling. Do not wipe till dry or tacky, wipe on wet, stand back
and let dry

To remove SHINE RESTORER/PROTECTOR from other
surfaces when wet, rinse with water and wipe off with a dry
towel.

Multiple coats of SHINE RESTORER/PROTECTOR are

recommended to increase the shine and protection properties.

Plastic surface must be dry to the touch prior to each application of

additional coats.

2

8

4

1

Five Minutes
Drying Time

7

3

5

6

9

Select a paper shop towel and fold in quarters (1).

Thoroughly shake the

BRIGHT SOLUTIONS HEADLAMP

CLEANER/POLISH before applying to towel. Shake the
container frequently throughout the cleaning process.

Open the specially formulated

BRIGHT SOLUTIONS

HEADLAMP CLEANER/POLISH, saturate a small area of
the towel (2), and begin cleaning the entire lens with a circular
motion (3).

Continue polishing and adding more HEADLAMP CLEANER/

POLISH as necessary to polish the entire lamp lens.

When lens has achieved a highly polished appearance, wipe off all

polish residue with Pretreatment

Proceed to

STEP 4

.

STEP 3

POLISHING

Advertising