Symtech Platinum Series Kit - Manual

BRIGHT SOLUTIONS
PLATINUM SERIES Kit
HEADLAMP Resurfacer / Protector
Thank you for purchasing BRIGHT SOLUTIONS
PLATINUM SERIES Kit, this is a 3 or 4 STEP process that
takes approximately 5~10 MINUTES to perform per headlamp
dependent upon severity of damage of lamp lens. By applying the
patented Preserver, your headlamp cleaning will be preserved for
more than two years.
KEEP OUT OF THE REACH OF CHILDREN
DO NOT ALLOW PRODUCT TO FREEZE
WHEN APPLYING PRODUCT IN TEMPERATURES
BELOW 60 o , TURN LAMPS ON UNTIL WARM.
DO NOT APPLY SHINE RESTORER/ PROTECTOR IN
DIRECT SUNLIGHT
READ INSTRUCTIONS IN ENTIRETY BEFORE USE.
USE GLOVES TO PROTECT HANDS.
Safety by Design
Can Be Used on : Headlamps Taillights
Turn Signal Lights Reflective Lens Covers
FIRST determine the extent of damage that has occurred over time to
your headlamp lens.
IF Headlamp lens is slightly fogged and or yellowed, without
visible hairline scratches or crazing, in most cases, the lamp
could be simply cleaned clear without sanding.
Steps 1, 3
and 4
IF Headlamp lens has extensive yellowing, scratches, crazing,
and/or pits, sanding is necessary to obtain a successful
result. Regardless of damage, sanding during cleaning will
speed the process dramatically.
Steps 1, 2 ,3 and 4
STEP 1
CLEANING
Remove all contents from package.
Using a paper towel, fold in quarters (1).
Thoroughly shake the Water Based Pretreatment before applying to
towel.
Open the specially formulated Water Based Pretreatment, saturate the
towel (2), and begin cleaning the entire lens with a circular
motion (3).
Continue cleaning, changing the towel surface and adding more Water
Based Pretreatment as towel becomes discolored (4) with dirt
and oxidation film of lamp lens.
When dirt and discoloring ceases to be removed from lens, Proceed to
STEP 2 or 3 .
NOTE: Masking area around headlamp (5) is highly
recommended to assure that painted and/or chromed
surfaces are not harmed during sanding process
Have a spray bottle of water handy (6), start with 600 grit sanding disc
applied to rotary sander, spray lens with water and begin sanding
the entire surface of the lens, wetting lamp (7) as needed to
prevent buildup of particles.
Note: Removal of deteriorated material should be fairly
quick.
Continue sanding until all discolored plastic has been removed from
lamp surface and residue of sanding is white in appearance.
Sanding is complete when lamp lens is uniform in appearance.
Take the 1500 grit sanding disc, apply to rotary sander, spray lens with
water and sand the entire surface of the lens, wetting lens (7) as
needed. This process will reduce the sanding lines .
Proceed to STEP 3
Use a lint free towel and fold in quarters (1).
NOTE: Apply SHINE RESTORER/ PROTECTOR
out of direct sunlight. WHEN APPLYING
PRODUCT IN TEMPERATURES BELOW 60
o ,
TURN LAMPS ON UNTIL WARM
Apply a liberal amount of the SHINE RESTORER/
PROTECTOR to a clean lint-free paper towel (10) and
apply it smoothly across the plastic surface (11), avoiding any
runs or bubbling. Do not wipe until dry or tacky, wipe on
wet, stand back and let dry
To remove SHINE RESTORER/PROTECTOR from
other surfaces when wet, rinse with water and wipe off with
a dry towel.
Multiple coats of SHINE RESTORER/PROTECTOR, two
coats are recommended to increase the shine and protection
properties.
Plastic surface must be dry to the touch prior to each application
of additional coats. Average drying time between coats is
less than 5 minutes.
2
4
1 3
Apply polishing disc to rotary sander
Thoroughly shake the HEADLAMP CLEANER/POLISH, shaking
container frequently throughout the cleaning process.
Open the specially formulated HEADLAMP CLEANER/POLISH,
saturate a small area of the polishing pad (8), and begin cleaning
the entire lens with a circular motion (9).
STEP 3
POLISHING
PAGE 1
A
s with any repair versus replacement, some items will not
achieve like new results. If directions are followed, significant
improvement in the appearance of the items will be achieved.
As we are unable to supervise the application process, user
assumes all risks. The manufacturer and its distributors are
not liable for any damages incurred by the use of this product.
If you are unsure as to the application process or compatibility
of the item you would like to resurface, please contact the
manufacturer or distributor for advice on how to proceed.
524 S.E. Transport Drive
Lee’s Summit, Missouri 64081
816-525-9263 FAX: 816-525-9383
www.symtechcorp.net
Continue polishing and adding more HEADLAMP CLEANER/
POLISH as necessary to polish the entire lamp lens.
When lens has achieved a highly polished appearance, wipe off all
polish residue with Water Based Pretreatment
Proceed to STEP 4 .
STEP 3 (continued)
POLISHING
STEP 4
SHINE RESTORER / PRESERVER
APPLICATION
STEP 2
SANDING
11
5 6
7 9
10 Less than Five
Minutes Drying
Time
8