Panasonic SA-AX6 - Manual (Page 36)

Technical specifications (DIN 45 500)
2X100 W (6 Ì2)
2X80 W (6 П}
0.05% {6 Q)
0.03% (6 a)
Ki AMPLIFIER SECTION
Power output (at 240 V for Australia and N.Z.
(at 127 V for others)
DIN 1 kHz(T.H.D. 1%)
20 Hz-20 kHz continuous power output
both channels driven
Total harmonic distortion
rated power at 20 Hz-20 kHz
half power at 1 kHz
Power output at the Dolby Pro Logic operation
DIN 1 kHz(T.H.D. 1%)
Front (for Australia and N.Z.) 2X100 W (6 U)
(for others) 2X85 W (6 ii)
Center (for Australia and N.Z.) 100 W (6 Q)
(for others) 85 W (6 Q)
Surround (for Australia and N.Z.) 2X100 W (6 O)
- (for others) 2X85 W (6 ii)
Subwoofer (fslOO Hz) (for Australia and N.Z.) 100 W (6 i2)
(for others) 85 W (6 Q)
Power bandwidth
both channels driven, -3dB 10 Hz-40 kHz (6 il)
Damping factor 30 (6 ii)
Load impedance
Front
A o r B 4-16 Q
A and B 8-16 Q
BI-WIRE 6-16 0
Center 6-16 O
Surround 6-16 0
Subwoofer 6-16 0
Frequency response
PHONO RIAA standard curve
(30 Hz-15 kHz) ±0.8 dB
CD, TAPE, DVD, VCR 1, TVA/CR 2, VCR 3
10 Hz-40 kHz, ±3 dB
Input sensitivity and impedance
PHONO 3 mV/ 47 kO
CD, TAPE, DVD, VCR 1, TV/VCR 2, VCR 3 200 mV/ 22 kO
S/N at rated power (6 O)
PHONO 70dB(IHF, A:80dB)
CD, TAPE, DVD, VCR 1, TVA/CR 2, VCR 3
75 dB (IHF, A: 85 dB)
Tone controls
BASS
TREBLE
Output voltage
TAPE REC (OUT), VCR 1 OUT
Channel balance (250 Hz-6.3 kHz)
Channel separation
Adaptive control (volume at-30 dB)
Headphones output level and impedance
Subwoofer cut off frequency control
50 Hz. +10 to -10dB
20 kHz, +10 to -10 dB
200 mV
±1 dB
55 dB
. 50 Hz, +Э dB
430 mV/330 a
50-200 Hz
Total harmonic distortion
MONO
STEREO
S/N
MONO
STEREO
Frequency response
20 Hz-15 kHz
Aiternate channel selectivity
£400 kHz
Capture ratio
Image rejection at 98 MHz
IF rejection at 98 MHz
Spurious response rejection at 98 MHz
AM suppression
Stereo separation
1 kHz
Carrier leak
19 kHz
38 kHz
Channel balance (250 Hz-6.3 kHz)
Limiting point
Bandwidth
IF amplifier
FM demodulator
Antenna terminal
0 . 2 %
0.3%
60 dB (75 dB, !HF)
58 dB (71 dB.iHF)
+1 dB, -2 dB
65 dB
1.5 dB
40 dB
70 dB
70 dB
50 dB
40 dB
-30dB(-35 dB, IHF)
-50 dB (-55 dB, IHF)
±1.5 dB
1.2 pV
180 kHz
1000 kHz
75 ii (unbalanced)
m AM TUNER SECTION
Frequency range
Sensitivity
Selectivity (at 999 kHz)
IF rejection (at 999 kHz)
522-1611 kHz (9 kHz steps)
530-1620 kHz (10 kHz steps)
20 pV, 330 pV/m
55 dB
50 dB
m VIDEO SECTION
Output voltage at 1 V input (unbalanced) 1 ±0.1 Vp-p
Maicimum input voltage 1.5 Vp-p
Input/output impedance 75 U(unbalanced)
m GENERAL
Power supply
For Australia and N.Z.
For others
Power consumption
Dimensions ( W X H X D )
Weight
AC 230-240 V, 50 Hz
AC 110-127 V/220-240 V, 50/60 Hz
300 W
430X158X378.4 mm
11 kg
Notes:
1. Specifications are subject to change without notice.
Weight and dimensions are approximate.
2. Total harmonic distortion is measured by the digital spectrum
analyzer.
m FM TUNER SECTION
Frequency range
Sensitivity
S/N 30 dB
S/N 26 dB
S/N 20 dB
IHF usabte sensitivity
IHF 46 dB stereo quieting sensitivity
87,50-108.00 MHz
1,5pV/75n
1.3 pV/75 a
1.2 pV/75 Q.
1.5pV/75a(IHF’58)
22 pV/75
Maintenance
If the surfaces are dirty
To clean this unit, wipe with a soft, dry cloth.
If the surfaces are extremely dirty, use a soft cloth dipped in a soap-
and-water solution or a weak detergent solution,
« Never use alcohol, paint thinner or benzine to clean this unit.
»Before using chemicaity impregnated cloth, read the instructions
that came with the cloth carefully.
Matsushita Electric Industrial Co., Ltd.
Osaka 542-8588, Japan
RQT4465-L
H0593V0