Warning, Important, How to replace the fuse – Panasonic CF-25 User Manual

Page 3: Warnings, For u.s.a, For u.k

Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".

Advertising
background image

For U.S.A.

Federal

Communications

Commission

R a d i o

Frequency Interference Statement

Note This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules These limits are designed to provide reasonable
protection against harmful interference in a residential
installation TTiis equipment generates, uses and can radiate radio
frequency energy and if not installed and used in accordance
with the instructions may cause harmful interference to radio
communications However there is no guarantee that interference
will not occur in a particular installation If this equipment does
cause harmful interference to radio or television reception which

can be determined by turning the equipment oft and on the user

IS encouraged to try to correct the interference by one or more
of the following measures

• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected

• Consult the Panasonic Service Center or an experienced ra-

dio/TV technician for help

Warning
To assure continued compliance use only shielded interface
cables when connecting to a computer or peripheral Also any
changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate this equipment
This device complies with Part 15 of the FCC Rules Operation
IS subject to the following two conditions
(1) This device may not cause harmful interference and
(2) This device must accept any intcrierence received including

iniciference that may cause undesired operation

For U.K.

FORYOUR SAFETY PLEASE READ THE FOLLOWING

TEXT CAREFULLY
This appliance is supplied with a moulded three pm mains plug

for your safety and convenience

A 3 amp tuse is fitted in this plug

Should the fuse need to be replaced please ensure that the re­
placement fuse has a rating of 3 amps and that it is approved by
ASTA o r B S I t o B S 1362

Check tor the ASTA mark or the BSI mark ^ on the body
of the fuse

If the plug contains a removable fuse cover you must ensure that

It IS lefittcd when the fuse is replaced

II you lose the (use covei the plug must not be used until a re­

placement cover IS obtained
A replacement tuse cover can be purchased fioin your local

Panasonic Dealer

I F T H C FITTED MOULDED PLUG IS UNSUITABLE FOR

11 IE SOCKET OUTLET IN YOUR HOME I HEN THE FUSE

SHOULD BE REMOVED AND THE PLUG CUT OFF AND
DISPOSED OF SAFELY

THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK

IF THE CUT OFF PLUG IS INSERTED INTO ANY 13 AMP

SOCKET

If a new plug IS to be fitted please observe the wiring code as

shown below

If in any doubt please consult a qualified electncian

Important

The wires m this mains lead are coloured in accordance with the

following code
Blue

Neutral

Brown

Live

As the colours of the wires in the mains lead of this apparatus
may not correspond with the coloured markings idcntilying the
terminals in your plug proceed as follows

The wire which is coloured Blue must be connected to the ter­

minal which IS marked with the letter N or coloured BLACK

The wire which is coloured Brown must be connected to the
terminal which is marked with the letter L or coloured RED

Under no circumstances should either of these wires be con­

nected to the earth terminal of the three pin plug marked with
the letter E or the Earth Symbol ^

The mams plug on this equipment must be used to disconnect
the mams power

Please ensure that a socket outlet is available near the equipment

and shall be easily accessible

How to replace the fuse

open

the f u s e compartment with a

screwdriver and replace the fuse

Warnings

• This equipment is not designed for connection to an IT power

system

(An IT system is a system having no direct connections be­
tween live parts and Earth the exposed-conducive-ptuis of the
electrical installation are earthed
An IT system is not pemiiUed wheie the computer is directly
connected to public supply systems m the U K )

• Disconnect the mams plug from the supply socket when the

computer is not in use

This equipment is produced to BS800/1983

Advertising