California Faucets Diverter for Roman Tub User Manual

Hand held shower, Roman tub set with diverter, Roman tub spout connectors

Advertising
background image

Fig. 1

RT.1_ii_140122

Tel: 714-891-7797
Fax: 714-891-2478
Toll Free: 800-822-8855

www.calfaucets.com

& HAND HELD SHOWER

P 1

INSTALLATION
INSTRUCTIONS

ROMAN TUB SET WITH DIVERTER

Series 6308 uses
Broach Adapter

Quick Connect
Model #: QC-63

Use With Rough Kit #:

08-75-63

For Series #:

6308

-Remove brass nut, plastic washer and rubber washer from
Quick Connect assembly.
-Ensure that O-ring is properly seated in brass washer.
-Insert Quick Connect assembly through hole in deck.
-Place Rubber Washer, Plastic Washer and Brass Nut onto
Shank from below and firmly tighten.
-Seat Spout onto Quick Connect.
-Rotate Spout to desired position and tighten setscrew.
-Use thread sealant to seal all fittings with threads.

Rubber
Washer

Brass Washer

w/ O-Ring

Brass Nut

For all Quick Connect except: 08-75-75

For Series #:

Use With Rough Kit #:

Model #: QC-50

Quick Connect

5008

Shank

Plastic
Washer

08-75-50

3208 3308 3408 3508
3608 3808 4008 4208
4408 4508 4608 4708
5108 5508 5708 5808
5908 6008 6108 6408
6708 6808 6908 E208

For Series #:

08-75-99

Use With Rough Kit #:

Model #: QC-99

Quick Connect

Brass Spacer

O-Ring

1

3/4"
Shank

Washer

Model #: QC-75

Use With Rough Kit #:

-Apply thread selant to one end of the Shank and
tighten into Spout.
-Place spout base ring (if applicable) onto deck, over
the spout shank.
-Insert Shank through deck hole and from below place
Washer and Nut onto Shank.
-Rotate Spout to desired postion and firmly tighten nut.
-Use thread sealant to seal all fittings with threads.

For Quick Connect: 08-75-75

Quick Connect

Use With Rough Kit #:

Model #: QC-63

For Series #:

Fig. 3

4808
4808X

6508
6608

08-75-65

For Series #:

5308

7008
7208
7308

3/4" Nipple

08-75-75

Nut

Roman Tub Spout Connectors

Fig. 2A

Fig. 2B

Fig. 2C

Fig. 2D

Fig. 2E

Hot

Inlet

Cold

Inlet

Handle

Escutcheon

Base Ring

(if applicable)

Spout

Base Ring

(if applicable)

IMPORTANT: All soldering shall be performed prior to attaching fitting to Valves and Quick

Connect, otherwise severe damage may take place and void warrantee

ø1"

Hole Size

ø1-1/2"

Hole Size

"A"

"A"

ø1-1/4"

Hole Size

ø1-1/4"

Hole Size

See

Step 4

Leader

Hose

Use Rigid

Copper Pipe

California Faucets reserves the right to make modification and specification changes at any time. Please visit www.calfaucets.com for most current technical data.

CALIFORNIA FAUCETS RECOMMENDS THAT ALL PLUMBING PRODUCTS BE INSTALLED BY A LICENSED ROFESSIONAL

NOTE:

-Must use rigid copper piping
(not flex) for all connections
between spout and valves.

-It is also recommended that an
access panel be provided for
all Roman Tub installations.

Advertising
This manual is related to the following products: