Dispensers clogged or leaking, Load too wet, Residue or lint on load – Kenmore 110.4597 User Manual

Page 20: Did you add detergent to the dispenser, Stains on load, Did you properly sort the load, Load is wrinkled, Did you unload the washer promptly, Cycle too long, Is “sud” shown in the display

Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".

Advertising
background image

Dispensers clogged or leaking

Are the laundry products in the correct dispenser

compartment?

Add the correct amounts of detergent, fabric softener or liquid

chlorine bleach to the correct compartments. Add powdered
or liquid color-safe bleach to the detergent compartment.

Be sure to match powdered color-safe bleach with powdered
detergent or match liquid color-safe bleach with liquid
detergent.

Is the detergent separator in the correct position?
Separator should be in the front position when using liquid
detergent and in the back position when using powdered
detergent.

Load too wet

Did you use the right cycle for the load being washed?
Select a cycle with a higher spin speed.

Did you wash a single item or bulky items or have you
overloaded the washer?

A single item, bulky items, or overloading may cause

imbalance. Add items or try to evenly distribute your wet
laundry in the drum, and start a DRAIN & SPIN cycle. If the
laundry is still wet, take half of the load out of the washer and

try again.

Residue or lint on load

Did you add detergent to the dispenser?
For best results, add detergent to the detergent
compartment. Do not add detergent to the washer drum.

Did you sort properly?
Sort lint givers (towels, chenille) from lint takers (corduroy,
synthetics). Also, sort by color.

Did you overload the washer?
Do not overload the washer. The washer can be fully loaded,
but not tightly packed. The wash load must be balanced. Lint
can be trapped in the load if overloaded.

Check the following:
Was paper or tissue left in pockets?

Did you use enough detergent?
Follow manufacturer’s directions. Use enough detergent to
hold the lint in the water.

Is your water colder than 70°F (21 °C)?
Wash water colder than 70°F (21 °C) may not completely
dissolve the detergent.

Are you using a low-speed wash cycle?

Powdered detergents may not dissolve well in a slow-speed
cycle. For best results, use liquid detergent for slow-speed
cycles such as Handwash/Delicate.

Stains on load

Did you add detergent to the dispenser?
For best results, add detergent to the detergent
compartment. Do not add detergent to the washer drum.

Did you use enough detergent?
Use enough detergent to remove soil and hold it in suspension.
For best performance, use a High Efficiency detergent.
Follow manufacturer’s recommendations for the type of load

you are washing.

Is there above average iron (rust) in water?
You may need to install an iron filter.

Did you properly sort the load?
Sort dark clothes from whites and lights.

Did you unload the washer promptly?

To avoid dye transfer, unload the washer as soon as it stops.

Did you use a fabric softener dispensing ball?
Dispensing balls will not operate correctly with this washer.

Add liquid fabric softener to the fabric softener compartment.

Did you use powdered detergent in a low-speed cycle?
Consider using liquid detergent.

Load is wrinkled

Did you unload the washer promptly?
Unload the washer as soon as it stops.

Did you use the right cycle for the load being washed?
Use the Handwash/Delicate cycle or another cycle with a
low-spin speed to reduce wrinkling.

Did you overload the washer?

The wash load must be balanced and not overloaded. Loads
should tumble freely during washing.

Gray whites, dingy colors

Did you properly sort the load?
Dye transfer can occur when mixing whites and colors in a
load. Sort dark clothes from whites and lights.

Was the wash temperature too low?

Use hot or warm washes if safe for the load. Make sure your
hot water system is adequate to provide a hot water wash.

Did you use enough detergent, or do you have hard

water?

Use more detergent for washing heavy soils in cold or hard

water.

Cycle too long

Is “SUD” shown in the display?
Excessive sudsing has been detected, and a suds routine has
been started to reduce excessive suds. This routine will add

time to the original cycle.

Did the load cause imbalance?

When too much imbalance occurs, an imbalance routine will
start to distribute the load. During the imbalance routine the
time displayed may pause until this activity is complete, then
resume with the remainder of the cycle.

Did you select the Handwash/Delicate wash cycle?

When using Handwash/Delicate wash cycle you should use
small loads. This ensures a gentle wash for your garments
without increasing cycle times.

Door locked at end of wash cycle

Did all of the water drain out of the washer during the
spin?
Select DRAIN & SFIN to remove any water remaining In the

washer. The washer door will unlock at the end of the drain.

20

Advertising
This manual is related to the following products: