Check installation dimensions, Disconnect sink drain, Disassemble new disposer mounting assembly – Kenmore 72785 User Manual
Page 2: Install flange in sink hole, Attach upper mounting assembly to sink flange, Instruction, Hole, Upper, Flange, Install flange in sink
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
INSTRUCTION
CHECK INSTALLATION DIMENSIONS
A. Disposer Height
B. Distance from bottom of sink
bowl to centerline of discharge
outlet. (Add 1/2" when stainless
steel sink is used.)
C: Distance from centerline of
the discharge outlet to end
of discharge tube.
D: Disposer Width
E; Distance from disposer vertical
centerline to centerline of
P-trap connection.
F; Centerline of disposer discharge to centerline at waste pipe entering wall.
(Dimension “F" must be greater than 1/4" to prevent standing water in disposer.)
If replacing an existing disposer, skip ahead to Instruction 6.
If this is a first time installation, continue with Instruction 2.
DISCONNECT SINK DRAIN
1. Loosen nut (A) at top of “P-trap" with pipe wrench (see Figure 2-1).
2. Loosen nut (B) at top of extension pipe. Remove extension pipe.
3. Loosen nut (C) at base of sink flange. (If nut is corroded or too tight, apply
penetrating lubricant)
4. Push sink flange up through sink hole and remove it (see Figure 2-2).
5. Clean sink flange area of any putty or other debris.
2
.
DISASSEMBLE NEW DISPOSER
MOUNTING ASSEMBLY
Insert wrenchette (or screwdriver) into one mounting lug and hold lower mount
ing ring securely with one hand (see Figure 3-1). With your other hand, turn
mounting assembly counterclockwise to remove mounting assembly from lower
mounting ring
Turn mounting assembly over (see Figure 3-2) and loosen three mounting
screws (A) until you can access snap ring (B).
Use screwdriver to pry snap ring off of sink flange. Mounting assembly will
now come apart.
INSTALL FLANGE IN SINK
HOLE
Model
A
B
C
D
E
6010/6012 11 3/8"
6"
4"
6 5/16"
5"
6011/6013 12 5/8"
6"
4"
6 5/16"
5"
60552
12 5/8"
6"
4"
7 1/4"
5"
60553
12 5/8"
6"
4"
7 1/4"
5"
60554
12 3/4"
6 11/16"
4"
8 1/2"
5 3/4"
60556
12 3/4"
6 11/16"
4"
8 1/2"
5 3/4"
60559*
15 7/8"
9 7/16"
4"
7 1/2"
5 3/4"
60562
12 5/8"
6"
4"
7 1/4"
5"
60563
12 5/8"
6"
4"
7 1/4"
5"
** Indicates Batch Feed Model
2
.
3.
Roll 1/4 pound (4 oz.) of non-hardening plumber’s putty to make 3/4" thick rope
to seal around sink flange.
Apply putty evenly around sink hole (see Figure 4-1).
Press sink flange slowly but firmly into sink drain hole to seat evenly on putty
(see Figure 4-2). Use screwdriver or putty knife to scrape all putty from edge
of sink hole.
Do not use plumber's putty on any other disposer connection - it
may harm disposer and cause property damage.
ATTACH
UPPER
MOUNTING ASSEMBLY TO SINK
FLANGE
You may wish to place a weighted object in the sink to hold the sink flange in place. (Place a towel
under object in sink to prevent scratching ) Reference Figure 5-1 for part identification.
1
Working from under sink, slip fiber gasket and
metal backup ring over sink flange.
2
Holding fiber gasket and backup ring in place,
slip mounting ring over sink flange so it seats
against backup ring
3
With fiber gasket, backup ring, and mounting
ring tight to s,r.!\ boltorr,, slide snap ring onto
sink flange until it pops into groove on flange*.
I Tighten three mounting screws up to sink
until mounting assembly is seated tightly
and evenly against sink.
Placing a thick, wide rubber band around
the sink flange (above the snap ring
groove) may help hold parts in place while
installing snap ring. (Remember to rehiove
rubber band after snap ring is installed.) '
If you are replacing an existing disposer, go to Instruction 6 If this is a first time installation,
skip ahead to Instruction 7
Sink Flange
Fiber Gasket
Backup Ring ____
Mounting Ring ___
Screws (3) ____
Snap Ring ______
5-1