0 master level meter (master level), Interrupteur d'alimentation (power) – Pioneer DJM-500 User Manual

Page 9

Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".

Advertising
background image

NAME AND FUNCTION OF PARTS

DENOMINATION ET FONCTION DES ELEMENTS

(D CH1 to CH4 input Selection Switch and Control

Knob/Peak level meter

Input selection switch:

Selects which sound of the two units connected to each
CH to use.

CHI : Switches between CD1/LINE and LINE
CH2 : Switches between CD2/LINE and PHONO 1
CHS : Switches between LINE and PHONO 2
CH4 : Switches between SUB MIC and PHONO 3

TRIM:

Used for adjusting the level of the input signal.

The level increases when rotated to the right. (To +6 dB)
The level decreases when rotated to the left. (To

-oo)

HI:

Used for adjusting the high tone.
Flat at center click.
Increases when rotated to the right. (To +12 dB at 10 kHz)

Decreases when rotated to the left. (To -20 dB at 10 kHz)

MID:

Used for adjusting the middle tone.
Flat at center click.
Increases when rotated to the right. (To +12 dB at 1 kHz)

Decreases when rotated to the left. (To -20 dB at 1 kHz)

LOW:

Used for adjusting the low tone.

Flat at center click.
Increases when rotated to the right. (To +12 dB at 100 Hz)

Decreases when rotated to the left. (To -20 dB at 100 Hz)

Peak level meter:

Displays the peak level holding it for two seconds.
Displays the level before channel fader.

The display range is about -24 dB to +14 dB.
When BPM is selected using the effect selector and the

effect switch is turned on, the beat monitor function will

be turned on.

Master Output Monaural/Stereo Selection

Switch (MONO/STEREO)

0

Master level meter (MASTER LEVEL)

Displays the output level after master volume adjustment

while holding it for 2 seconds.
The display range is -24 dB to +14 dB.

Power Supply Switch (POWER)

(

2

)

Sélecteur d'entrées de CHI à CH4 et bouton

de contrôle/Indicateur du niveau de pic so­

nore

Sélecteur d'entrées:

Celui-ci sélecte le son provenant d'un des deux appareils
connectés à chaque CH à utiliser.

CH1 : Commutation entre CD1/LINE et LINE

Commutation entre CD2/LINE et PHONO 1
Commutation entre LINE et PHONO 2
Commutation entre SUB MIC et PHONO 3

CH2
CH3
CH4

TRIM:

Utilisé pour ajuster le niveau du signal d'entrée.

Tournez vers la droite pour augmenter le niveau. (Jusque
+6dB)
Tournez vers la gauche pour diminuer le signal. (Jusque -<>o)

Hl:

Utilisé pour ajuster les sons aigus.

Centre de la portée avec déclic.

Tournez vers la droite pour augmenter. (Jusqu'à +12 dB à

10 kHz)

Tournez vers la gauche pour diminuer. (Jusqu'à -20 dB à

10 kHz)

MID:

Utilisé pour ajuster les sons de hauteur moyenne.

Centre de la portée avec déclic.

Tournez vers la droite pour augmenter. (Jusqu'à +12 dB à

1 kHz)

Tournez vers la gauche pour diminuer. (Jusqu'à -20 dB à

1 kHz)

LOW:

Utilisé pour ajuster les sons graves.

Centre de la portée avec déclic.

Tournez vers la droite pour augmenter. (Jusqu'à +12 dB à

100 Hz)

Tournez vers la gauche pour diminuer. (Jusqu'à -20 dB à

100 Hz)

Indicateur du niveau de pic:

Celui-ci affiche le niveau de pic en le maintenant durant 2
secondes.

Le niveau affiché est celui avant le curseur de volume de

canal.

La plage d'affichage s'étend d'environ -24 dB à +14 dB.
La fonction du moniteur de battements s'enclenchera lors­

que BPM est choisi à partir du sélecteur d'effet et que l'in­

terrupteur d'effets est enclenché.

I

I

Commutateur Monaural/Stéréo de sortie de
mélodie principale (MONO/STEREO)

® Indicateur de niveau de la mélodie principale

(MASTER LEVEL)

Celui-ci affiche le niveau de sortie après la sélection de
volume de la mélodie principale en le maintenant durant
2 secondes.

La portée de l'affichage s'étend de -24 dB à +14 dB.

Interrupteur d'alimentation (POWER)

9

<DRB1279>

En/Fr

Advertising