Pioneer S-H310V - Manual

S-H3nOV
S-H3^ ov-w
SPEAKER SYSTEM
ENCEINTE ACOUSTIQUE
LAUTSPRECHERSYSTEM
SISTEMA ALTOPARLANTE
LUIDSPREKERSYSTEEM
HÒGTALARSYSTEM
SISTEMA DE ALTAVOCES
SISTEMA DE ALTIFALANTES
OPERATING GUIDE
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
GUIDA PER l ’ uso
GEBRUIKSAANWIJZING
BRUKSANVISNING
GUÍA DE OPERACIÓN
GUIA DE OPERAQÄO
Ç English ^
BEFORE OPERATION
• Thank you for buying this PIONEER product.
• Read the operating instructions carefully before using these speakers
so that you can operate them properly. After you have finished reading
the instructions, put them away in a safe place for future reference.
• The rated impedance of these speakers is 8 Ohms. They must be
connected to a stereo amplifier which accepts this type of load (miminum
and maximum impedances accepted by the amplifier are generally
indicated near the loudspeaker outlets : for example "4-16 Q." or "6-16 H").
• To guard against damage to these speakers due to an electric power
overload, take the following precaustions :
o Do not supply more than the maximum permitted power to the
speakers (see Specifications).
o Any connection or switching on or off of part of the audio system
(CD player, tuner etc.) must be carried out after switching off the
amplifier or at least with the loudspeaker outlets disconnected (if the
amplifier allows). Interference caused by these operations will
otherwise reach the speakers and may damage the treble
loudspeaker units.
o When boosting particular frequencies using a graphic equaliser or
bass and treble correctors, make sure that you do not increase the
amplifier volume excessively, as the speakers will be overloaded more
quickly.
o Do not force a low-power amplifier to produce a high level of sound
as harmonic distortion increases rapidly in this situation and may pose
a danger to the treble loudspeaker units.
• Avoid touching the diaphragms and suspensions of loudspeakers as
they are fragile.
® Strip the insulation at
the tip of the cord and
twist the strands
® Turn the thumbscrew anti­
clockwise, make sure that the speaker
cord is inserted well into the hole and
turn the thumbscrew clockwise to
The loudspeaker units in these speakers are magnetically shielded.
However, colours may blur if the speakers are positioned too close
to a television screen. If this happens, switch off the television and
switch it back on again after 15 to 30 minutes. If the problem persists,
move the speakers away from the television set.
UIU
INSTALLATION PRECAUTIONS
• Attach the base to the bottom of the speaker using the screws supplied (see diagram
below).
• Do not install these speakers close to an oven or heating
appliance. Avoid exposing them to direct sunlight. High
temperatures can distort the structure of the enclosure and
adversely affect the sound.
• These speakers are heavy and fragile, and it is therefore
dangerous to install them in an unstable position. For
added safety, it is advisable to attach these speakers to a
wall or pillar using chains and hooks (not supplied). To do
so, stretch the chains between the ties located on the
rear of the speakers and the hooks.
• For optimum sound reproduction of high frequencies, the
treble loudspeaker units must be at the same height as the
listener’s ears. For low frequencies, it is possible to increase
the level of bass sounds by positioning the speakers close to a wall (the maximum increase
being obtained for a position in a corner of the listening room).
CONNECTIONS
1. Switch off the amplifier power supply (OFF).
2. Connect the cables to the input terminals on the rear of the speakers.
Connect the neutral cable to the "-" terminal and the live cable to the "-r"
terminal. Do not forget that the red input terminal has positive polarity and
that the black input terminal has negative polarity.
3. Connect the cables to the loudspeaker outlet terminals of the amplifier.
Connect the live cable to the "-r" terminal and the neutral cable to the "-"
terminal.
J
m
side speaker cord tho the
0 terminal.
® Connect the hot-side speaker cord
tho the © terminal.
REMARKS:
• Check that the cables are securely connected to the terminals. A
loose connection may cause not Just Intermittent or distorted sound but
short-circuiting and breakdown of the amplifier.
• If the cables of one of the speakers have been connected with the wrong
polarities, you will find when listening to a stereo recording that bass
sounds are weakened and the stereo effect normally obtained between
the two speakers does not exist.
MAINTENANCE OF THE ENCLOSURE
• Use a cloth to wipe away dust and dirt.
• If the enclosure is very dirty, wipe with a soft cloth dipped in a neutral
detergent diluted five to six times with water, then wipe again with the dry
cloth. Do not use thinner, benzene, cleaning sprays or other chemical
products on or near the enclosures as the surfaces could be adversely
affected.
SPECIFICATIONS
Speaker ......................................................... floor-standing type, bass-reflex
System ................................................................... 2-way, 3 loudspeaker units
Loudspeaker units : Bass.................................2 cone woofers, 14 cm
Treble..............................1 dome tweeter, 2.5 cm
Rated impedance....................................................................................8 Q
Frequency range (-3 dB) ........................................................ 35 - 35000 Hz
Sensitivity ............................................................... 90 dB/W at 1 m distance
Music power (DIN): .................................................................................100 W
External dimensions :
With base............................. 240 x 925 x 345 mm (W x H x D)
Without base........................184 X 900 X 318 mm (W x H x D)
Weight ........ .................................................................................................11.5 kg
Accessories
Operating instructions.............................................................................................1
Warranty................................................................................................................. 1
Cables.................................................................................................................... 1
Base -r screws.................................................................................................. 1+4
Ties + screws ..................................................................................................2 + 4
REMARK:
The specifications and design of this product are subject to change
without notice, in the interests of improvements.
Published by Pioneer Corporation.
© 2001 Pioneer Corporation.
All reproduction and translation rights reserved.