Crosman MCSR01 - Manual

MCSR01
6mm Plastic BBs
OWNER’S MANUAL
READ ALL INSTRUCTIONS AND WARNINGS IN THIS
MANUAL BEFORE USING THIS AIRSOFT GUN
Marine Corps trademarks used under license by Crosman Corporation.
Distributed by
Crosman Corporation
7629 Routes 5 & 20
Bloomfield, NY 14469 USA
www.crosman.com
(800) 724-7486
Made in Taiwan ASR39-515
WARNING:
This is not a toy. Adult supervision is required. Misuse may cause serious
injury, especially to the eye. Eye protection designed for airsoft guns must be worn by the
user and any person in range. May be dangerous up to 100 yds. Read the owner’s manual
before using.
WARNING:
Do not brandish or display this airsoft gun in public – it may confuse people
and may be a crime. Police and others may think it is a firearm. Do not change the coloration
and markings to make it look more like a firearm. That is dangerous and may be a crime.
WARNING:
This product contains a chemical known to the state of California to cause
cancer and birth defects (and other reproductive harm).
YOU AND OTHERS WITH YOU SHOULD ALWAYS WEAR EYE PROTECTION TO PROTECT YOUR EYES.
READ ALL INSTRUCTIONS AND WARNINGS IN THIS MANUAL BEFORE USING THIS AIRSOFT GUN.
BUYER AND USER HAVE THE DUTY TO OBEY ALL LAWS ABOUT THE USE
AND OWNERSHIP OF THIS AIRSOFT GUN.
Recommend 18 years or older to purchase. Intended for use by those 16 or older.
Please read this owner’s manual completely. Remember to treat this airsoft gun with the same respect you would a
firearm. Always carefully follow the safety instructions found in this owner’s manual and keep this manual in a safe
place for future use.
If you have any questions regarding your new airsoft gun, please contact Crosman Customer Service at: 1-800-724-
7486, 585-657-6161 or www.crosman.com.
1. Learning the names of the parts of your new airsoft gun will help you to understand your owner’s manual. Use
this manual to increase your enjoyment of this soft air gun.
A. Barrel
B. Muzzle
C. Rear Sight
D. Front Sight
E. Safety (Fig. 2A & 2B)
F. Clip Release
G. Trigger
H. Clip
I. Bolt (cocking handle)
J. Stock Release lever (Fig. 3)
K. Stock
L. Stock Latch
M. Hop-Up adjustment
2. Operating the Safety
WARNING:
Keep the airsoft gun in the “ON SAFE” position until you are ready to
shoot. Then turn the safety to the “OFF SAFE” position.
A. To Put the Airsoft Gun “ON SAFE”:
• Locate the safety on the left side of the receiver. (Fig. 2A)
• Turn the lever all the way to the rear so the arrow is pointing to the word “SAFE”.
Like all mechanical devices, an airsoft gun safety can fail. Even when the safety is “On
Safe”, you should continue to handle the airsoft gun safely. NEVER point the airsoft gun at
any person. NEVER point the airsoft gun at anything you do not intend to shoot
B. To Take the Airsoft Gun “OFF SAFE”
• Locate the safety on the left side of the receiver. (Fig. 2B)
• Turn the lever all the way to the front so the arrow is pointing to the word “FIRE”
• The airsoft gun is “OFF SAFE” and ready to fire when pointing to “FIRE”.
3. Extending and Folding the Stock
Before extending or folding your stock make sure your airsoft gun is “ON SAFE”, (see sec-
tion 2.1) and pointed in a SAFE DIRECTION.
A. Extending the Stock
• Make sure the airsoft gun is “ON SAFE” (See Section 2.A) and pointed in a SAFE
DIRECTION.
• Gently lift the stock up and out releasing it from the stock latch (Fig. 3A)
• Fold the stock out and lock it into position. (Fig. 3B)
B. Folding the Stock
• Make sure the airsoft gun is “ON SAFE” (See Section 2.A) and pointed in a SAFE
DIRECTION.
• Push the stock release button and fold the stock onto the stock latch.
4. Loading and Unloading Plastic BBs
WARNING:
Use 6 mm airsoft BBs only in this airsoft gun. Use of any other ammunition
can cause injury to you or damage to the airsoft gun. NEVER RE-USE AMMUNITION.
A. Loading Plastic BBs
• Make sure the airsoft gun is “ON SAFE” (See Section 2.1) and pointed in a
SAFE DIRECTION.
• Push the clip release button to remove the clip.
• Pull down the BB guide and push it to the left until it locks into place.
• Holding the clip upright, pull open the reservoir door on the top of the clip.
• Fill the clip reservoir with up to 350 BBs and close the door.
• Holding the clip horizontally as shown (Fig. 4) shake the clip until up to 18 BBs
feed into the magazine.
• Release the BB guide by pushing the BB guide to the right and slowly releasing.
• Insert the loaded clip back into the airsoft gun until you hear it click, indicating that the
clip is securely locked into place.
B. Unloading Plastic BBs
• Make sure the airsoft gun is “ON SAFE” (See Section 2.1) and pointed in a SAFE
DIRECTION.
• Push the clip release button to remove the clip.
• Holding the clip upright, pull open the reservoir door on the top of the clip.
• Pull down the BB guide and push it to the left until it locks into place.
• Shake the BBS out of the magazine and into the clip.
• Pour the airsoft BBs out of the reservoir into a container or your hand.
• Before replacing the magazine, shake the airsoft gun to release any plastic BBs which may have fallen out of the
magazine into the airsoft gun.
WARNING:
Never assume that because the airsoft gun no longer fires a plastic BB
and/or the magazine is removed, that a plastic BB is not lodged in the barrel. Always treat
the airsoft gun as though it is loaded and with the same respect you would a firearm.
5. Cocking the gun
Note: You must cock the airsoft gun before each and every shot.
• Make sure the airsoft gun is “ON SAFE” (See Section 2.1) and pointed in a SAFE
DIRECTION
• Make sure the magazine is loaded and installed in the gun.
• Locate the cocking handle at the back of the airsoft gun and pull the handle back until
it clicks. (Fig. 5)
• Release the handle.
• The airsoft gun is now cocked and ready to fire.
6. Aiming and Firing Safely
• You and others with you should always wear eye protection designed for airsoft to
protect your eyes.
• Always point your airsoft gun in a SAFE DIRECTION.
• Do not shoot at hard surfaces or at the surface of water. The plastic BBs may bounce
off or ricochet and hit someone or something you had not intended to hit.
• DO NOT re-use plastic BBs because they could damage your airsoft gun.
• Your airsoft gun is designed for target shooting and is suited for both indoor and
outdoor use. Always remember to place your target carefully. THINK about what you
will hit if you miss the target.
A. Adjusting the Sights
• Flip the sights up for use. Flip down for storage.
• The rear sight is designed with 4 peep settings. To find your preference, turn the rear
sight until it clicks into position. (Fig. 6)
• The airsoft gun is correctly aimed when the front sight blade is positioned exactly in
the center of the peep of the rear sight. The bulls-eye should appear to rest on the top of the front sight.
• When you are sure of your target and backstop, and the area around the target is clear, take the airsoft gun
“OFF SAFE” (section 2A) and pull the trigger to fire.
B. Adjusting the Hop Up
• Your airsoft gun is manufactured with a hop-up system. The purpose of this system is to change the spin on the
BB as it leaves the muzzle letting you adapt your shot for different distances.
SAFE
“ON SAFE”
Fig. 2A
FIRE
“OFF SAFE”
Fig. 2B
Fig. 3B
Fig. 3A
Fig. 4
Fig. 5
• Make sure the airsoft gun is “ON SAFE” (See Section 2.1) and pointed in a SAFE DIRECTION
• Remove the clip
• Locate the hop up adjustment slide on the right side of the gun.
• Push the slide back for less spin or forward for more spin.
7. Maintaining Your Airsoft Gun
• DO NOT MODIFY OR ALTER YOUR AIRSOFT GUN. Tampering with the airsoft gun or attempts to change the
airsoft gun in any way may make it unsafe to use and voids the warranty.
• If you drop your airsoft gun, visually check to see that it works properly before you
use it again. If anything seems changed, like a shorter or weaker trigger pull, this may
mean parts are worn out or broken. Call Customer Service at Crosman for assistance
before using your airsoft gun again.
A. To Clean the Barrel
• Turn off the hop up system by moving the adjustment all the way back.
• Make sure the airsoft gun is “ON SAFE” (See Section 2.A) and pointed in a SAFE
DIRECTION
• Remove the clip.
• Spray a cleaning patch with Crosman Nitro Lubricant oil.
• With patch on rod, insert in into barrel to clean
oSwab barrel 3-4 times
oRepeat swabbing procedure with a dry patch
• Barrel is clean when patches come out clean after dry swabbing.
B. Clearing a Jam
• Never look down the end of barrel to see if a jam has been cleared.
• Make sure the airsoft gun is “ON SAFE” (See Section 2.A) and pointed in a SAFE DIRECTION
• Remove the clip from the airsoft gun.
• Insert the tapered end of the cleaning rod into the barrel, with the angle toward the breech (where the magazine
connects).
• CAREFULLY and slowly apply more pressure until you push the BB out of the breech.
• Replace the clip and test gun.
8. Reviewing Safety
• Do not ever point the airsoft gun at any person. Do not ever point the airsoft gun at anything you do not intend
to shoot.
• Always treat the airsoft gun as though it is loaded and with the same respect you would a firearm.
• Always aim in a SAFE DIRECTION. Always keep the muzzle of the Airsoft gun pointed in a SAFE DIRECTION.
• Always keep the airsoft gun “ON SAFE” until you are ready to shoot in a SAFE DIRECTION.
• Always check to see if the airsoft gun is “ON SAFE” and unloaded when getting it from another person or from
storage.
• Always keep your finger off the trigger and out of the trigger guard until ready to shoot.
• You and others with you should always wear eye protection to protect your eyes.
• Always wear eye protection designed for airsoft over your regular glasses.
• Use 6 mm plastic BBs only.
• Do not reuse plastic BBs because they could cause damage your airsoft gun.
• Do not shoot at hard surfaces or at the surface of water. The plastic BBs may bounce off or ricochet and hit
someone or something you had not intended to hit.
• Replace the backstop if it becomes worn. Place the backstop in a location that is safe should the backstop fail.
• Your backstop should be checked for wear before and after each use. All backstops are subject to wear and
will eventually fail. Replace your backstop if the surface is worn or damaged or if a ricochet occurs.
• Do not attempt to disassemble or tamper with your airsoft gun.
• DO NOT MODIFY OR ALTER YOUR AIRSOFT GUN. Attempts to modify the airsoft gun in any way may make
your airsoft gun unsafe to use, cause serious injury or death and voids the warranty.
• Using unauthorized repair centers or modifying the function of your airsoft gun in any way may be unsafe and
voids your warranty.
• Do not put the airsoft gun away loaded. Make sure ALL of the plastic BBs are unloaded from the airsoft gun.
• Always store this airsoft gun in a secure location.
SPECIFICATIONS
Mechanism/Action Spring Air Repeater Weight 2.5 lbs
Caliber/Ammunition 6 mm airsoft BBs Overall Length 28 in
Magazine Up to 18 6mm airsoft BBs Sights
Front: Blade
Rear: Adjustable Size Peep
Clip/Reservoir Up to 350 6mm airsoft BBs Safety Lever
Velocity Up to 325 fps
PERFORMANCE: Many factors can affezct velocity, including brand of projectile, type of projectile and barrel condi-
tion.
DO NOT RETURN THIS PRODUCT TO THE STORE.
Our friendly customer service representatives will be glad to help. You can get answers to frequently asked
questions at www.crosman.com or you can contact us directly at 1-800-7AIRGUN (1-800-724-7486)
CUSTOMER SERVICE
If your airsoft gun is not functioning, we recommend that you call Crosman Corporation Customer service at 1-800-
724-7486 or 585-657-6161. (International customers should contact their distributor.) DO NOT ATTEMPT TO
DISASSEMBLE IT! If you take it apart you probably will not be able to reassemble it. Crosman assumes no warranty
responsibility under such circumstances.
LIMITED 30 DAY WARRANTY
This product is warranted to the retail consumer for 30 days from date of retail purchase against defects in material
and workmanship and is transferable.
WHAT IS COVERED
Replacement parts and labor. Transportation charges to consumer for repaired product.
WHAT IS NOT COVERED
Transportation charges to Crosman for product. Damages caused by abuse, modification or failure to perform nor-
mal maintenance. Any other expense. CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, OR INCIDENTAL
EXPENSES, INCLUDING DAMAGE TO PROPERTY. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITA-
TION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT
APPLY TO YOU.
WARRANTY CLAIMS
USA Customers: Attach your name, address, description of problem, phone number and copy of sales receipt to
product. Package and return to Crosman Corporation, Routes 5 & 20, East Bloomfield, NY 14443 USA.
International Customers: Return product to your nearest distributor. If you do not know your distributor call 585-
657-6161 and ask for our International Department for assistance.
IMPLIED WARRANTIES
ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO 30 DAYS FROM DATE OF RETAIL PURCHASE.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE
LIMITATIONS MAY NOT APPLY TO YOU.
To the extent any provision of this warranty is prohibited by federal, state, or municipal law which cannot be pre-
empted, it shall not be applicable. This warranty gives you specific legal rights, and you may have other rights which
vary from state to state.
CROSMAN is a registered trademark of Crosman Corporation in the United States.
Check out our complete line of Marine Corps airsoft products at marinesairsoft.com
For more information about the Marine Corps and becoming a Marine, visit marines.com
Officially Licensed Product of the United States Marine Corps, www.marines.com and 1.800.marines.
Fig. 6