EcoTech Marine Hanging Kit - Manual

R
adion Premium Hanging Kit Instructions
A
B
C
D
E
F
G
A. Hanging Cable x2
B. Mounting Screws x4
C. Grip Lock Screw x2
D. Grip Lock Body x2
E. Cable Mount Base x2
F. Cable Mount Cover x2
G. Eyelet Cable x2
Make sure that all you have all component on the hanging kit before beginning. If something is missing,
contact EcoTech Marine service at 1-800-785-0338.
Materials Included: Additional Materials Required:
1. 3 mm Allen Key
2. Mounting Hardware
* Dependent on mounting surface
3. Screwdriver
4. Wire Cutters
Step 1: Attach eyelet cable to grip
lock body
Slide eyelet cable into slot on grip lock
body. Fasten grip lock screw to bottom
of grip lock body. Repeat for both eyelet
cables.
Step 2: Attach eyelet cables to
Radion
Using included mounting screws, attach
eyelet cables to Radion.
Note: for ease of adjustment, position the grip lock
body so that the cable hole is facing outward.
Step 3: Attach Cable Mount Base
to Mounting Surface
Screw cable mount base into mounting
surface using the mounting points
determined by template on reverse side.
Step 4: Pull hanging cable through
Cable Mount Cover
Pull hanging cable through cable mount
cover until you cannot pull any further.
DO NOT trim cable until you are com-
pletely finished hanging the Radion.
Step 5: Screw Cable Mount Cover
and Hanging Cable onto Cable
Mount Base
Screw cable mount cover and cable onto
cable mount base. Make sure hardware
is securely fastened.
Step 6: Push Hanging cable
through Grip Lock Body
Push hanging cable through grip lock
body allowing excess cable to hang.
Step 7: Adjust Hanging Height and
Pitch with Grip Lock Assembly
To adjust the height of the Radion you
must either push more hanging cable
through grip lock or pull hanging cable
back up through grip lock.
To pull cable back, push release mecha-
nism on top of grip lock to release and pull
cable upward.
Step 8: Trim Excess Hanging Cable
Once you have completed the hanging of
your Radion. You may then use a wire cut-
ter to trim excess hanging cable. Be sure
to leave enough excess cable for height
adjustments and maintenance.
Use the template on the reverse side of this instruction sheet
to mark the desired hanging point screw locations above the
aquarium. Make sure to choose a mounting location that is
centered with respect to the desired location of your Radion.
*Choose mounting hardware that is appropriate for the material
into which you will be attaching the hanging kit. Certain surfaces
may require special materials to ensure that it will be capable of
holding weight of Radion.
For video tutorials or more information, please visit us at
ecotechmarine.com or visit our community knowledge base
at community.ecotechmarine.com.
Make sure to support your Radion above your tank while adjusting
the height and pitch. DO NOT release the Radion until you are sure
the cables are the appropriate length and the Radion is secure.
Once you have trimmed excess cable, you may not have the
ablility to lower the height of Radion.
Damage caused to Radion due to improper hanging or improper
materials is a liability of the customer and won’t be covered
under warranty (e.g. Radion slides off cable and into water).
Warnings:
• Do not install the Radion above the aquarium while it is plugged into an electrical
outlet. Mount the Radion first and then connect power to the fixture.
• EcoTech is not responsible for any damage to the Radion, your aquarium and its
livestock or your property as a result of improper use of the hanging kit.
• This hanging kit is designed to be utilized with one Radion fixture. While this kit
may hold more than one Radion fixture, EcoTech is not liable for any damages
that may occur for hanging kits used to mount more than one fixture
• Inspect the mounting location for the Radion for electrical devices, such as recep-
tacles and light switches, prior to installation. Improper installation through a live
electrical wire can cause serious injury or damage.
• Never hang pointed or sharp objects at eye level where they may come in contact
with persons.
Note: Parts may be pre-assembled for convenience
Mounting below the recommended above tank height of 8 inches may
expose the fixture to excessive moisture or contact with water. Water
damage is not covered under warranty.