Chamberlain SECURITY+ 6200-2K - Manual (Page 32)

32
Trolley
Trolley
Release Arm
NOTICE
Manual
Release Handle
(Pull Down)
Trolley
Trolley
Release Arm
NOTICE
Manual
Release Handle
(Pull Down & Back
Towards Opener)
Weak or broken springs could allow an open
door to fall (either rapidly or unexpectedly),
resulting in serious injury, death or property
damage. If possible, use the manual release
rope and handle
only when door is fully closed.
Operation of Your Opener
WARNING
Activate the opener with any of the following:
• The Remote Control: Hold the large push button
down until the door starts to move.
• The Door Control: Hold push bar down until the
door starts to move.
• The Outside Keylock or Keyless Entry.
(See Accessories)
When the opener is activated with the safety
reversing sensor installed and correctly aligned:
1. If open, the door will close. If closed, it will open.
2. If closing, the door will reverse.
3. If opening, the door will stop (allowing space for
entry and exit of pets and for fresh air).
4. If the door has been stopped in a partially open
position, it will close.
5. If obstructed while closing, the door will reverse.
6. If obstructed while opening, the door will stop.
7. The garage door will reverse in the closing cycle,
and the opener lights will blink for 5 seconds, when
the invisible beam is broken. If fully open, the door
will not close when the beam is broken. The sensor
has no effect in the opening cycle.
If the sensor is not installed, or is not aligned correctly,
the door won't close from any remote transmitter. You
can close the door with the Door Control, the Outside
Keylock, or Keyless Entry, however, if you activate
them
until down travel is complete. If you release
them too soon, the door will reverse.
The Opener Lights will turn on under the following
conditions: When the opener is initially plugged in;
when the power is interrupted; when the opener is
activated. It will turn off automatically after 4-1/2
minutes or provide constant light when the Light
feature on the Multi-Function Door Control is
activated. Bulb size is 75 watts maximum.
Lights will also turn on when someone walks through
the open garage door. With a
Multi-Function Door
Control, this feature may be turned off as follows: With
the opener lights off, press and hold the light button
for 10 seconds, until the light goes on and off again.
To restore this feature, start with the opener lights on,
then press and hold the light button for 10 seconds.
To open the door
manually:
The door should be fully
closed if possible. Pull
down on the manual
release handle and lift the
door manually. To
reconnect the door to the
opener, press the Door
Control push bar.
Manual disconnect
position
Lockout position
The lockout feature
prevents the trolley from
reconnecting automatically.
Pull the manual release
handle down and back
(toward the opener). The
door can then be raised
and lowered manually as
often as necessary. To
disengage the Lockout
Feature, pull the manual
release handle straight
down. The trolley will
reconnect on the next UP
or DOWN operation.
Door Control Push Bar: Press the white square to open or
close the door. Press again to
reverse the door during the
closing cycle or to stop the door while it's opening.
Light Feature: Press the Light button. If the opener light
is
off, it will turn on. If the opener light is on, (even in the 4-
1/2 minute automatic cycle) it will turn off.
But if you use the Light button to turn the lights on and
then activate the opener, the lights will turn off after
4-1/2 minutes.
The 4-1/2 minutes interval can be changed to 1-1/2,
2-1/2, or 3-1/2 minutes as follows: Press and hold the
Lock button until the light blinks (about 10 seconds).
A single blink indicates that the timer is reset to 1-1/2
minutes. Repeat the procedure and the light will blink
twice, resetting the timer to 2-1/2 minutes.Repeat again
for a 3-1/2 minute interval, etc., up to a maximum of four
blinks and 4-1/2 minutes.
The Light button will not control the opener lights when the
door is in motion.
Lock Feature: The Lock feature is designed to prevent
operation of the door from remote controls. However, the
door will
open and close from the Door Control push bar,
the Outside Keylock and the Keyless Entry Accessories.
To Activate: Press and hold the Lock button for
2 seconds. The push bar light will flash as long as the
Lock feature is
on.
To turn off: Press and hold the Lock button again for 2
seconds. The push bar light will stop flashing. Normal
operation will resume. The Lock feature will also turn off
whenever the “Smart” button on the opener panel is
activated.
Operation of the Multi-Function Door Control
(See additional programming features, next page.)