Casio DQ-584B - Manual (Page 2)

Operation Guide DQ-584/584B
USING THE ALARM
The alarm sounds when the current time reaches the alarm time. The face illuminates for the first 5 seconds of the
alarm operation as well. The alarm tone alternates between two levels.
You can also use the Alarm Mode selector 6 to select the snooze alarm feature.
Setting the Alarm Time
1. Slide the Mode switch 5 to
“AL”. This causes the alarm time
setting to flash on the display.
2. Use the 12 • 24HR (YEAR)
button 2 , MIN (DATE) button
3 , and HR (MONTH) button 4
to set the alarm time. Holding
down the
MIN (DATE) button 3
or HR (MONTH) button 4
changes the corresponding
setting at high speed.
• Make sure you set the correct
am/pm time if you are using 12-
hour timekeeping. The PM
indicator indicates PM times,
while nothing is indicated for AM
times.
3. Slide the Mode switch 5 to “NORMAL”. This will cause
the figures on the display to stop flashing.
4. Turning the Alarm On and Off
Use the Alarm Mode selector 6 on the top of the clock
to turn the alarm on and off, and to select the snooze
feature.
Alarm Mode selector Description
The alarm sounds at the preset time for one minute. You can stop the alarm by
pressing the
SNOOZE/LIGHT button 1 . The snooze feature will cause the alarm to
sound again about five minutes after it stops. A indicator flashes on the display
during the period between alarms.
• If you keep stopping the alarm manually by pressing the SNOOZE/LIGHT button 1 1 1 1 1
The alarm will sound again, about five minutes after you stop it.
• If the alarm is not stopped manually
The alarm will sound three times for one minute, at five-minute intervals. After that the
snooze feature will be cancelled automatically.
The alarm sounds at the preset time for one minute.
The alarm does not sound.
SNZ
ON
OFF
Hour Minutes
Press to toggle between
12-hour and 24-hour
timekeeping. Press to advance the
alarm time minute setting. Press to advance the
alarm time hour setting.
USING THE LIGHT
Hold down the SNOOZE/LIGHT button 1 to illuminate the display. The light will go out automatically after about
three seconds, even if you keep the button depressed.
Important!
• Overuse of the light can shorten battery life.
THERMOMETER FUNCTIONS
A built-in sensor measures temperature and shows the measured value on the display.
Temperature Measurements
• The temperature display shows “LO” for temperatures below –19.5 ° C (–3.0 ° F) and “HI” for temperatures above
70 ° C (158 ° F).
• Though temperature readings are displayed up to 0 ° C (32 ° F) and greater than 41 ° C (105 ° F), note that such
readings actually are outside the guaranteed temperature range of this clock.
Switching between Celsius and Fahrenheit
• Push the ° C/ ° F button 7 to select either Celsius ( ° C) or Fahrenheit ( ° F).
Celsius ( °C) Fahrenheit ( °F)
°C/°F button ( 7 )
BATTERY REPLACEMENT
Replace the battery whenever the display of the clock becomes dim and difficult to read.
1. Open the battery compartment cover as shown in the illustration.
2. Remove the old battery.
3. Load a new battery. Make sure that the positive (+) and negative (–) ends of the battery are facing correctly. An
incorrectly loaded battery can burst and damage the clock.
4. Replace the battery compartment cover.
Battery precautions
• Keep batteries out of the reach of small children. If a battery is swallowed accidentally, contact your physician
immediately.
• Be sure to load the battery with its positive (+) and negative (–) ends facing correctly.
• Never charge the battery that comes with the clock.
• Should a battery ever leak while in the clock, wipe out the fluid with a cloth, taking care not to let any get onto
your skin.
• Replace the battery at least once a year, even if the current battery is working properly.
• The battery that comes with the clock loses some power during transport and storage.
• The light also turns on for the first five seconds that the alarm sounds.
Stopping the Alarm
•
When alarm is sounding, press the SNOOZE/LIGHT button 1 to stop it. When the snooze feature is turned on,
the alarm will sound again in about five minutes.
• To turn off the snooze feature, slide the Alarm Mode selector 6 to OFF.
Testing the alarm
• While the mode switch setting is “NORMAL”, hold down the HR (MONTH) button 4 and MIN (DATE) button 3
at the same time to sound the alarm. All of the display’s digital segments will appear at this time. Release the
buttons to stop the alarm.
2