Sears EverYoung 88800F - Manual (Page 2)

IVI A UNI I tIMAíMUC
Troubleshooting with error codes
The 88800F electronics continuously runs a self
check, (f ii finds an irregularity, the electronic con­
sole will display an error code, and stop normal
operation.
ERROR CODE PESCRlPTiOW
F1
SPEED SENSOR ERROR
F2 SPEED ERROR
F3 ELEVATION SYSTEM ERROR
For "FI" or "F2” error code : Follow the Cali­
brating speed then the Resetting error codes pro­
cedures below to reset the treadmill for normal op­
eration.
For "F3" error code: Follow the Calibrating % rn-
cfine then the Resetting error codes procedures
below to reset the treadmill for nortnai operation.
C a t i b rati n g s peed a n d % Inc I ine
NOTE: If you need assisiance, phase confaci
yoiir nearesi aifthorizoci service center before
aftemptlny the following procedures.
(phase nolo modal number and saiial «).
Failure to do so may x'ald your warranty.
Calibrating Speed
1. Press and hold the "ON/OFF" butlon to light
up all the segments of LEDs.
2. Press and hold the ser Program butfona.
3. Release the ser Program button, a eep"
will follow enabling the calibration mode.
4. Release the N/OFF button. All display v^n-
dovvs will be blank.
5. Press the peed Slow button, SP L will
display in the Time window and the running belt
speed Vflil display In the Calones window. Use the
Speed fast and slow buttons to adjust the mini­
mum running belt speed to 110 M.P.H. Do not ad­
just defauft values for speed
6. Press the tart/Stopj. buttrjri to r.et the low
Speed and enter the Speed high mode.- :
7. Ph will display in the Time window and the
runnirrg beii speed will display in the Calories win­
dow. Use the- peed fast and stow buttons 1o
adjust the maximum running bell speed to; 10.0
Syt.P-H. ; , ■: T : "
Do not adjust default values for speed
8. Press the tarf/Stop: button to set the 10.0
mph speed and to quit the calibration mode.
Calibrating %incHrte
i. Press and hold the "ON/OFF" button to light,
up all, tire segments of LEDs.
2, Press and hold the ser Prrjgram. buttons,-
eep” 3. Release the set Program button, a
Sivill follow enabling the calibration mode.,
4, Release the N/OFF button. All display win­
dows vJi be Wank.
5. Press the INCLINE UP button. Lu now
displays in the Time display The treadmill aufo-
mallcaily adjusts to the highest possible ^Incline.
Allow the elevation system,-and number in the
CALORIE window to, stabilize. .
6. Once the number has stabilized m the Calorie
window, press the tart/ Stop button to set and
prontpt the computer to find the lowest value for
%lncrine, L d now displays tn the TIME win­
dow.
/ . , V
7. Once the elevation system and number have
stabilized press the tart/Stop button to finish
calibration of %lrrciinoL v ::
; ' ■: ^
Resetting error codes/ /
In the rare event of the treadmill displaying an er­
ror code {th_e letter followed by a number) on
the computer 'display please Mow these inslruc-
üons to resurne normal operation: ' ^ : ;T' //;
liohi 1, Press and, hold the "ON/OFE" button lb
up all the segm.ents-of LEDsv-i ' ^,7- ■■
2.' Press and hold *ne seriPiogfam- buttons^
Release the ser Program butlon, a eep'
wiirfotipw enabling the callbraUbn.mode. ,,,:
4; , Release the: M/OFF,, button. All display win­
dows are now blank or-off.
5. Press the Program ; INTERVAL butlon. Thè
RR code should now be removed and your
treadmill should now be ,ready for normal’usé.
Cleaning
Before proceeding ensure that the treadmill
power IS off and that it is unplugged from the elec­
trical outlet. IS- To remove dust use a email vacuum
nozzle to carefully vacuum around all visible com­
ponents. cs- To remove film or dirt use a slightly
damp rag with a mlid cleaning agent sprayed onto
the rag on!y. w Careful not to immerse any tread­
mill component v/ith any (iquids.
Inspect Fasteners and Wiring
Check that all fasteners are properly tightened and
ail wiring is securely m place, ts- To avoid damag­
ing fasteners, do not over tighten.
Moving
The treadmlil has been designed and equipped with
wheels for easy mobillly. o- Before moving, en­
sure the master power switch is in the off position
and the power cord Is unplugged from the electri­
cal Qutiet. «r Lift the front or rear end of the tread-
mi(i, then roli the treadmlil to the desired position.
Storage
Store your treadmil! in a dean and dry environ­
ment, Ensure the master power switch is off and
is unplugged ftom the electrical wall outlet.
evERYOUNO ” BliOOOF TRÎADM1LL OWNER’S MANUAL