Akai Multi Video Processor RMD-V3104U User Manual
Rmd-v3104u, Acaunoim, Operating ir^tructions mode cfemploi
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
PIONEER’
The Art of Brt&tainment
Operating ir^tructions
Mode cfemploi
RMD-V3104U
MULTI VIDEO PROCESSOR 1-lnput 4-Output (NTSC)
PROCESSEUR VIDEO MULTI SORTIE a 1 entrées et 4 sorties (NTSC)
Read and un€hrstand these "Operating instructions^
before operating.
Obey all the warnings on the product.
English^
WARNING: TO PREVENT FIRE OR SHOCK HAZARD.
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
Frânçâi^^
IMPORTANT NOTICE:
RECORD
THE
MODEL
NUMBER
AND
SERIAL
NUMBER
OF
THIS
EQUIPMENT
BELOW.
THE
NUMBERS ARE ON THE REAR PANEL.
MODEL NO.
SERIAL NO.
RMD-V3104U
KEEP THESE NUMBERS FOR FUTURE USE.
ACAUnOIM
k When positioning this equipment, ensure that the
mains plug and socket in are easily accessible.
IMPORTANT
A
I
CAUTION
I
RISK OF ELECTRIC SHOCK
DO WOT OPEN
A
The I ¡ghtning flash with a rrowhead symbol, within
an equilateral triangle, is Intended to alert the
user to the presence of uninsulated 'dangerous
voltage' within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to persons.
CAUTION:
TO PREVENT THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). NO USER-
SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL
The exclemation point within an equilateral
triangle is intended to alert the user to the
presence
of
important
operating
and
mainter>ance (servicing) instructions in the
literature accompanying the appliance.
Information to User
Alteration or modifications carried out without appropriate authorization may invalidate the user's right to operate the
equipment.
Document Outline
- IMPORTANT NOTICE:
- RECORD THE MODEL NUMBER AND SERIAL NUMBER OF THIS EQUIPMENT BELOW. THE NUMBERS ARE ON THE REAR PANEL.
- MODEL NO. SERIAL NO.
- RMD-V3104U
- KEEP THESE NUMBERS FOR FUTURE USE.
- IMPORTANT
- INTRODUCTION
- PRECAUTIONS UPON USE A
- • Power cord precautions A
- Completefy plug in the cord
- Use only 100 -120 V ^
- Removing dust
- When problems occur ^
- • Never disassemble the system
- When objects fall inside the system Jk.
- When not using for long periods Jk
- Avoid high temperatures and humidity Jk
- PRECAUTIONS UPON USE A
- INSTALLATION PRECAUTIONS
- FEATURES
- CONTROLS AND CONNECTORS
- TROUBLESHOOTING
- SPECIFICATIONS
- Multi-Video Processor RMD-V3104U
- 2. CONNECTION WITH MVP EXTERNAL COMPUTER
- 3. INSTRUCTIONS FOR USING A COMPUTER AS A TERMINAL
- 5. MVP VIDEO OUTPUT MODES
- 6. ADJUSTMENT FUNCTIONS
- 7. PICTURE FRAME ADJUSTMENT PROCEDURES
- (1) Connect the RS-232C cable to the MVP panel.
- (2) Initialize the picture frame data in RAM.
- (3) Set to the magnified screen to be adjusted.
- (4) Perform coarse adjustment of the picture frame.
- (5) Perform fine adjustment of the picture frame.
- (6) Repeat steps (4) and (5) for every position on the screen.
- (7) Save the adjustment data in the EEPROM.
- 1. Command reference
- 2. Adjusting the picture frame
- 3. To switch the image input [IFF command]
- 4. To indicate the current MVP state [SYS command]
- 5. To perform NTSC input board picture quality adjustment
- 6. Controls the panel switch function
- (1) To set the manual mode [MNL command]
- (2) To set the remote mode [RMT command]
- (3) To select composite video input [CIC command]
- (4) To select YC separation input [YIC command]
- (5) To set the output to the NTSC mode [NT command]
- (6) To set the output to standard RGB mode [NTR command]
- (7) To set the output to the double-speed RGB mode [NTD command]
- (8) Optional variable scan board adjustment mode settings [:A command]
- 8. DEMO PATTERN SETTINGS AND CAUTIONS
- 9. INSTALLING AND REMOVING BOARDS
- 10. RMD-V3020 COMMAND REFERENCE
- (1) Outline of the RMD-V3020
- (2) VS board command rules
- (3) Tracking adjustment [TRK command]
- (4) Contrast adjustment [CNT command]
- (5) R, G, B gain adjustment [RGN, GGN, BGN commands]
- (6) Brightness adjustment [BRT command]
- (7) B, R clamp adjustment [BLV, RLV commands]
- (8) Blanking window level adjustment [BLK command]
- (9) Horizontal, vertical direction screen display position adjustment [HPS, VPS commands]
- (10) Horizontal, vertical blanking window position adjustment [HWN, VWN commands]
- (11) Horizontal, vertical blanking window width adjustment
- [HWD, VWD commands]
- (12) Full dot number compensation [HFD command]
- (13) Freeze frame Y:ON N:OFF [FZY, FZN commands]
- (14) Vertical filter ON/OFF [DSY, DSN, DSX commands]
- (15) Vertical compression filter conversion rate input [LCV command]
- (16) Program ROM version display [VER command]
- (17) To indicate the current function setting [STS command]
- (18) To select preset model [M command]
- (19) Model fresh [F command]
- (20) Measurement data display [FRQ command]
- (21) Model table reference [TBL command]
- (22) Horizontal frequency input [HFQ command]
- (23) Vertical frequency input [VFQ command]
- (24) Vertical full-line input [VLN command]
- (25) All reset [ARS command]
- 11. MODE 99
- 12. VS BOARD MODEL SELECTION
- 13. USING METHODS OF HFQ, VFQ, VLN
- 14. SELECTING THE SYNC SIGNAL