EZ-ACCESS SUITCAS TRIFOLD AS RAMP User Manual

Trifold ramp, Instructions for use

Advertising
background image

10258 REV 2-26-14

Patented

CE Technical Files kept at: Enable Access, Marshmoor Works Great North Road, North Horth Mymms Hatfield, AL9 5SD, UK

© 2005-2013 Homecare Products, Inc. All rights reserved.

TRIFOLD RAMP

INSTRUCTIONS FOR USE

Optional top lip extension is available. See below or contact your local EZ-ACCESS retailer for details.

1.

Maximum weight limit is 800 pounds.

2.

Read and follow all instructions before use.

3.

Do not use if ramp is damaged or unstable.

4.

For wheelchairs and scooters only (not intended for commercial use).

5.

Ramp is shipped fully assembled. To separate ramp into two halves
for easy stowage and transportation, remove bolts and install coil
tension safety pin as follows:

a. Position as shown in (

DIAGRAM

1). Align hinges, then insert coil

tension safety pin into each hinge assembly and connect ramp
sections together before use. NOTE: Spring section of pin
should be on the underside (non-treaded side) of ramp.

b.

WARNING: Ramp may be separated for use when loading or

unloading unoccupied mobility equipment only.

c.

WARNING: When used with occupied mobility equipment,

use ramp as one unit (ensure both halves are joined with pins or
bolts firmly installed before use).

6.

Place ramp on landing in the folded position, making sure that the top
lip (labeled TOP) is resting securely on the landing (

DIAGRAM

2).

7.

Position ramp approximately its full length out from vehicle or step.
Facing vehicle or step, begin working from the left side. Stand ramp
upright on end with the hinged edge facing to the right. Lift up first top
half of ramp toward step or vehicle and place ramp so that the top lip
is securely supporting the ramp as shown in

DIAGRAM

2.

8.

Unfold second top half of ramp so that both halves are fully extended
lengthwise with one half laying face down on top of the other. NOTE:
Non-skid tread should NOT be exposed at this time.

9.

Open complete ramp, exposing entire non-skid surface and center on
landing as shown in

DIAGRAM

3.

10.

For ease in carrying and stowage, ramp can be disconnected and
carried in two sections. (When pins are not in use, store in one side
of hinge or on the underside of ramp by inserting into the gap behind
the top I-beam.)

11.

To prevent ramp halves from swinging open, ensure that the Dual Lock

™ tab

(interlocking fastener) is pressed together and firmly locked in place. NOTE:
Prior to use, locate both of the 1” x ¾” Dual Lock tabs (found on the non-skid
side of the ramp, near the top and bottom edges), and then remove the top
piece (it’s used only as a protective covering during shipping).

12.

WARNING: Ensure top lip is secure before using ramp. We recommend

attaching ramp

temporarily to the landing using provided clevis pins (drill ¼”

hole in landing) or semi-permanently using screws through pre-drilled holes
at the top of each section. To prevent ramp from becoming dislodged during
use, make sure that the top lip overlaps the resting surface as far as
possible. The surface holding the top lip needs to be substantial and of
sound construction.

13.

WARNING: Use ramp only with a qualified helper and always use lap belt.

14.

WARNING: An incline chart is provided on the reverse side of this

document. However, it is intended only as a guideline. It is important that you
refer to your equipment's (wheelchair or scooter) Owner Guide for the proper
degree of incline/decline and chair direction before using ramp. Never
exceed its recommendations.

15.

SAFETY & MAINTENANCE: Regularly check ramp for damage, and check
and tighten any loose fasteners. Keep ramp surface clear of ice, snow, dirt,
leaves, and other debris. For snow/ice, remove accumulation and sweep the
surface clean. To remove dirt, leaves, and other debris, sweeping the surface
or using a garden hose will usually suffice, but, if needed, use a damp cloth
or soft brush with non-alkaloid detergent and water. Rinse well and use extra
caution if ramp surface is wet.

16.

OPTIONAL FEATURE: Increase the usefulness of the TRIFOLD

®

Advantage

Series

®

Ramp with the Top Lip Extension (TLE). This optional extension

increases the standard 3” lip to become 9”, allowing the ramp to clear the
rear bumper of SUVs and vans by simply attaching to the top lip of the ramp
(

DIAGRAM

4). TLE is for use with unoccupied mobility equipment only and,

when used, reduces the overall ramp weight capacity to 500 pounds.
Contact your local retailer or visit www.ezaccess.com for details.

DIAGRAM 1

DIAGRAM 2

DIAGRAM 3

DIAGRAM 4

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

1. EZ-ACCESS, a division of Homecare Products, Inc., (herein referred to as Manufacturer), warrants that the equipment shall be free from defects in material and

workmanship under normal use and service for a period of 3-years from the date of original purchase. This limited warranty applies to the original purchaser only
and is non-transferable. This limited warranty is applicable to defective metal structure components only (excludes powder coated finish, applied non-skid tread,
etc.) No part of this warranty will apply to any equipment which has been subject to misuse, vandalism, negligence, alteration, improper loads, accident,

improper installation, or which has been repaired outside Manufacturer’s place of business in any way as in the reasonable judgment of Manufacturer, to adversely affect its
performance and reliability, nor to normal deterioration due to wear, tear and exposure, corrosion, or damage caused by rain, fire, earthquake or other natural causes or acts of
nature.

2.

Manufacturer’s obligation and purchaser’s sole remedy under this warranty is limited to, at Manufacturer’s option, repairing or replacing equipment which is returned to its place of

business and which, upon examination, shall disclose to Manufacturer’s reasonable satisfaction to have been defective. Manufacturer will make the repair or replacement of
defective components at its own expense. If Purchaser discovers a defect, he/she must call Manufacturer at 253-249-1101 to request a Return Authorization (RA) to return the
merchandise to Manufacturer.

3. If Manufacturer determines, in its sole discretion, to replace the equipment with either a new or repaired unit, purchaser shall be responsible for a charge prorated on the following

basis: The purchaser will be allowed a credit against the purchase price of equivalent equipment at the time of return to Manufacturer, in proportion to the percentage of the
warranted service life remaining at the time of such return. Purchaser will be responsible to pay the balance of the purchase price of equivalent equipment. Manufacturer reserves
the right to require payment prior to delivery of the repaired/replaced equipment. In calculating available credit, the remaining warranted service life will be rounded up or down to
the nearest whole year. YEARS 0-1: Unit repaired or replaced; YEARS 1-2: Repair or 50% $ credit (current purchase price multiplied by credit percentage); YEARS 2-3: Repair or
25% $ credit (current purchase price multiplied by credit percentage). This limited warranty does not cover removal or reinstallation. Manufacturer reserves the right to require
Purchaser to pay for all shipping charges (Government purchases exempt).

4. DISCLAIMER: THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED

OR STATUTORY, INCLUDING ANY LIABILITY ARISING UNDER ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, STATUTORY OR
OTHERWISE. HOWEVER, THAT IF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN ANY TERRITORY WHERE A PRODUCT IS SOLD, THE DURATION OF SUCH
IMPLIED WARRANTY IS LIMITED TO THE DURATION OF THE LIMITED WARRANTY DESCRIBED IN THE FIRST PARAGRAPH.

5. MANUFACTURER SHALL NOT BE LIABLE UNDER ANY CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHER LEGAL OR EQUITABLE THEORY FOR ANY DIRECT,

SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES, RESULTING FROM THE USE, MISUSE OR INABILITY TO USE THE EQUIPMENT, OR ARISING OUT OF ANY
BREACH OF THIS LIMITED WARRANTY, EVEN IF MANUFACTURER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE SOLE REMEDY FO R A
BREACH OF THE FOREGOING LIMITED WARRANTY IS REPLACEMENT OF THE DEFECTIVE OR NON-CONFORMING EQUIPMENT OR PART. THE MAXIMUM LIABILITY
OF MANUFACTURER UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE PRICE OF THE EQUIPMENT COVERED BY THE WARRANTY.

6. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you

specific legal rights, and you may also have other rights which may vary from State to State. Manufacturer reserves the right to change or improve its products without any
obligation to change or improve any Product previously manufactured by it.

Advertising