Rigel Systems Skylite - Manual

™
Operation: Push thumbwheel forward or
backward to light, center position is off.
Low battery Indication: White LEDs don't
light, Red LEDs light dimly. This is normal
as white LEDs require higher voltage.
How to change the battery:
1) Unscrew thumb knob at bottom of battery
cover.
2) Remove battery cover and note sealing
ring location.
3) Remove battery and install new 9 volt
battery with positive pole of battery
against battery spring marked +.
(we recommend Alkaline or Lithium for
long life)
4) Verify sealing ring is on ledge & install
battery cover.
5) Screw in thumb knob clockwise until tight.
How to attach lanyard: Stretch loop over
thumb knob.
™
Operation: Push thumbwheel forward or
backward to light, center position is off.
Low battery Indication: White LEDs don't
light, Red LEDs light dimly. This is normal
as white LEDs require higher voltage.
How to change the battery:
1) Unscrew thumb knob at bottom of battery
cover.
2) Remove battery cover and note sealing
ring location.
3) Remove battery and install new 9 volt
battery with positive pole of battery
against battery spring marked +.
(we recommend Alkaline or Lithium for
long life)
4) Verify sealing ring is on ledge & install
battery cover.
5) Screw in thumb knob clockwise until tight.
How to attach lanyard: Stretch loop over
thumb knob.
™
Operation: Push thumbwheel forward or
backward to light, center position is off.
Low battery Indication: White LEDs don't
light, Red LEDs light dimly. This is normal
as white LEDs require higher voltage.
How to change the battery:
1) Unscrew thumb knob at bottom of battery
cover.
2) Remove battery cover and note sealing
ring location.
3) Remove battery and install new 9 volt
battery with positive pole of battery
against battery spring marked +.
(we recommend Alkaline or Lithium for
long life)
4) Verify sealing ring is on ledge & install
battery cover.
5) Screw in thumb knob clockwise until tight.
How to attach lanyard: Stretch loop over
thumb knob.
™
Operation: Push thumbwheel forward or
backward to light, center position is off.
Low battery Indication: White LEDs don't
light, Red LEDs light dimly. This is normal
as white LEDs require higher voltage.
How to change the battery:
1) Unscrew thumb knob at bottom of battery
cover.
2) Remove battery cover and note sealing
ring location.
3) Remove battery and install new 9 volt
battery with positive pole of battery
against battery spring marked +.
(we recommend Alkaline or Lithium for
long life)
4) Verify sealing ring is on ledge & install
battery cover.
5) Screw in thumb knob clockwise until tight.
How to attach lanyard: Stretch loop over
thumb knob.
™
Operation: Push thumbwheel forward or
backward to light, center position is off.
Low battery Indication: White LEDs don't
light, Red LEDs light dimly. This is normal
as white LEDs require higher voltage.
How to change the battery:
1) Unscrew thumb knob at bottom of battery
cover.
2) Remove battery cover and note sealing
ring location.
3) Remove battery and install new 9 volt
battery with positive pole of battery
against battery spring marked +.
(we recommend Alkaline or Lithium for
long life)
4) Verify sealing ring is on ledge & install
battery cover.
5) Screw in thumb knob clockwise until tight.
How to attach lanyard: Stretch loop over
thumb knob.
™
Operation: Push thumbwheel forward or
backward to light, center position is off.
Low battery Indication: White LEDs don't
light, Red LEDs light dimly. This is normal
as white LEDs require higher voltage.
How to change the battery:
1) Unscrew thumb knob at bottom of battery
cover.
2) Remove battery cover and note sealing
ring location.
3) Remove battery and install new 9 volt
battery with positive pole of battery
against battery spring marked +.
(we recommend Alkaline or Lithium for
long life)
4) Verify sealing ring is on ledge & install
battery cover.
5) Screw in thumb knob clockwise until tight.
How to attach lanyard: Stretch loop over
thumb knob.
™
Operation: Push thumbwheel forward or
backward to light, center position is off.
Low battery Indication: White LEDs don't
light, Red LEDs light dimly. This is normal
as white LEDs require higher voltage.
How to change the battery:
1) Unscrew thumb knob at bottom of battery
cover.
2) Remove battery cover and note sealing
ring location.
3) Remove battery and install new 9 volt
battery with positive pole of battery
against battery spring marked +.
(we recommend Alkaline or Lithium for
long life)
4) Verify sealing ring is on ledge & install
battery cover.
5) Screw in thumb knob clockwise until tight.
How to attach lanyard: Stretch loop over
thumb knob.
™
Operation: Push thumbwheel forward or
backward to light, center position is off.
Low battery Indication: White LEDs don't
light, Red LEDs light dimly. This is normal
as white LEDs require higher voltage.
How to change the battery:
1) Unscrew thumb knob at bottom of battery
cover.
2) Remove battery cover and note sealing
ring location.
3) Remove battery and install new 9 volt
battery with positive pole of battery
against battery spring marked +.
(we recommend Alkaline or Lithium for
long life)
4) Verify sealing ring is on ledge & install
battery cover.
5) Screw in thumb knob clockwise until tight.
How to attach lanyard: Stretch loop
over thumb knob.