Televes Encoder-Modulador ATSC-T HDMI & USB, DigiMod User Manual

Application / aplicación

Advertising
background image

Encoder/Modulator ATSC-T, HDMI & USB

Ref. 554952

Safety Instructions

WARNING: To prevent fire or electrical shock, do not expose the device to rain or moisture.

General Precautions

Avoid placing the device next to central heating components and in areas of high humidity.
Do not cover the device with elements that obstruct the ventilation slots.
If the encoder modulator has been kept in cold conditions for a long time, keep it in a warm room minimum 2 hours

before plugging into the mains.

Mount the encoder modulator in vertical position with the connectors located on the top side.
When replacement parts are required, be sure the service technician has used replacement parts specified by the

manufacturer or have the same characteristics as the original part. Unauthorized substitutes may result in fire, electric
shock or other hazards.

Safety check- Upon completion of any service or repairs to this device, ask the service technician to perform safety checks

to determine that the device is in proper condition.

Power precautions

The encoder modulator is powered with a voltage of 12V DC. The power supply voltage must not exceed the recommended

voltage, which otherwise may cause irreparable damage to the device and the invalidation of the warranty. Therefore:

- Do not replace power supply with a voltage greater than 12V DC.
- Do not connect the device to the power if the power cord is damaged.
- Do not plug the device into mains supply until all cables have been connected correctly.
- Do not cut the cord.

Instrucciones de seguridad

ADVERTENCIA: Para evitar incendios o descargas eléctricas, no exponga el equipo a la lluvia ni a la humedad.

Precauciones Generales

Evite colocar el dispositivo junto a componentes de calefacción y en zonas muy húmedas.
No cubra el equipo con elementos que obstruyan las ranuras de ventilación.
Si el equipo se ha mantenido en condiciones de frío durante mucho tiempo, guárdelo en un cuarto caliente por un

mínimo de 2 horas antes de conectarlo a la red eléctrica.

Monte el equipo en una superficie vertical, con los conectores situados en la parte superior.
Cuando se necesiten repuestos, asegúrese de que se utilicen las piezas especificadas por el fabricante o que tengan las

mismas características que las originales. Los repuestos no autorizados pueden provocar incendios, descargas eléctricas
u otros riesgos.

Comprobación de seguridad- Una vez efectuado cualquier servicio o reparación, pídale al servicio técnico que realice

comprobaciones de seguridad para determinar que se el equipo se encuentra en buen estado.

Precauciones Eléctricas

El equipo se alimenta con una tensión de 12Vdc. La tensión de alimentación no debe superar la tensión recomendada, de

lo contrario se pueden causar daños irreparables en el dispositivo y la cancelación de la garantía. Por lo tanto:

- No sustituya la fuente de alimentación con una tensión superior a 12Vdc.
- No conecte el equipo a la alimentación si el cable eléctrico está dañado.
- No conecte el dispositivo al suministro eléctrico hasta que todos los cables se hayan conectado correctamente.
- No corte el cable.

EN

ES

DC 12V

HDMI

YPbPr/S-Video/AV

Application / Aplicación

RF

IN

RF

OUT

YPbPr

S-Video

A/V

Power

ATSC-T

YPbPr

S-Video

SD/HD CAMERA

CCTV

Blu-ray / DVD

SAT SD/HD

HDMI

A/V

HDMI

TS FILES

LCD DISPLAY

Power/alarm/lock indicators

USB

(PVR/Playback/Upgrade)

JTAG port for upgrade

Control Buttons

RF In

RF Out

Advertising