Aervoe 80-Watt Solar Collector User Manual

Aervoe Equipment

Advertising
background image

MC4 Power Cable

Charge

Controller

Handles

Sierra Wave® 80-Watt Solar Collector #9580

IMPORTANT SAFEGUARDS

Read all instructions before operating and keep for reference. Only use as directed

To reduce the risk of electric shock, do not submerge the unit or its accessories in any

liquid.

Unit is weather resistant but not waterproof. Bring indoors during heavy rain, snow or

wind. If fixed-mounted, cover it up during heavy rain, snow or wind.

To avoid shock do not connect to a power center in wet conditions.

Protect solar panels from scratching. Do not place other objects on top of panels to

avoid damage.

Do not use abrasive cleaning products to clean solar panels

Store in a clean dry place when not in use

When using the 7A Charge Controller, follow instructions carefully to avoid personal

injury and explosion or other damage to batteries, the solar panel, or Charge Controller

Not intended for use by children. Administer close supervision when children are nearby

PARTS IDENTIFICATION

SOLAR COLLECTION & CHARGING

This portable 80-Watt Solar Collector features high-efficiency monocrystalline solar cells and

includes MC4 cables to quickly connect to many Sierra Wave power centers. Also includes a

built-in 7A solar charge controller with over-charge protection, battery cables to charge 12V

batteries, and a barrel power adapter to charge other portable electronic devices.

Two Solar Collectors may be chained together in parallel for 160-watts of power using #9502

Chainable Connector.

Solar Collector Set-Up:

1.

Unfold the Solar Collector by opening the side latches.

2.

Adjust the height of the KICK STAND SUPPORTS on the back so that the SOLAR PANELS

are directly facing the sun with maximum exposure. Adjustment will be required throughout

the day as the sun travels across the sky. Obstructions from trees and buildings will affect

efficiency.

Charging a Power Center (sold separately):

We recommend the #9675 1000-Watt Energy Center, #9680 1500-Watt Energy Center or #9690

1500-Watt Incremental Energy Center as a storage device (Power Center) for collected power.

Read all instructions included with the Power Center or any other device you choose (based on

compatibility). When using a Sierra Wave Power Center, the Charge Controller is not required.

CAUTION: Do not make cable connections to the solar collector or power center when under

load.

1.

Connect the MC4 POWER CABLES on the Solar Collector to the SOLAR CHARGE CABLE

included with your power center, matching the MC4 female end of one to the MC4 male end

of the other.

2.

Connect the other end to the DC IN port located on the power center or other device.

3.

Follow your power center’s charging instructions. Disconnect when a full charge is achieved

or when not in use.

Charging a 12V DC Auxiliary Battery (sold separately):

1.

Place the battery on a stable surface close to the Solar Collector.

2.

Connect the SAE connector on the BATTERY CLAMPS to the SAE connector on the

CHARGE CONTROLLER port labeled BATTERY.

3.

Connect the red (+) and black (-) BATTERY CLAMPS to the corresponding red (+) and

black (-) battery terminals.

4.

Monitor the charging status using the CHARGE CONTROLLER LED INDICATORS. See

chart below.

5.

A LOAD output of no more than 7A/100 watts may be connected to the CHARGE

CONTROLLER to directly operate from the 12V battery. Function is controlled by the

CHARGE CONTROLLER to ensure battery safety. Check your devices rated wattage

before using this function.

Barrel Power Adapter with SAE Connector

Battery Clamps with SAE Connector

DANGER

The Charge Controller must be used when charging 12V sealed lead acid and AGM

vehicle batteries. Failure to do so may cause a battery fire, explosion and personal

injury. Extreme caution must be taken to make certain all connections are secure

between the charge controller, solar collector, and load connected; and that the

battery cables are attached to the correct polarity terminals.

12V Battery

7A

Charge

Controller

Low

Voltage

Charging

High

Voltage

Load

Solar

Battery

Charge Controller LED Indicators

High Voltage Protection: If the 12V battery reaches a pre-
determined high voltage level of 14V-14.5V DC, the green
High Voltage LED Indicator will illuminate. Solar charging
to the battery will automatically stop until the battery
reaches a safe operating voltage.

Charging In Process: When the Solar Collector is connected,
the yellow Charging LED Indicator will illuminate as long as
adequate solar energy is provided.

Low Voltage Protection: If the 12V battery reaches a pre-
determined low voltage level of 11V ±0.3V the red Low
Voltage LED Indicator will illuminate. Operation of the
load will automatically stop until the battery reaches a safe
operating voltage.

Solar Collector

Charging Electronic Devices

Directly charge Sierra Wave power banks or electronic devices like tablets, smartphones,

cameras, GPS equipment, and tools. Your device’s 12V own charger is required for this

function. IMPORTANT: Charging laptops is not supported with this method because they

require 19-21V and higher wattage. Use the a Sierra Wave Solar Link 240, 1000 or Energy

Center 1500 to charge these items.

1.

Read all instructions included with the device you wish to charge to confirm

compatibility. Power requirements must not exceed Solar Collector rated output.

2.

Place your device on a stable surface next to the Solar Collector.

3.

Connect the included BARREL POWER ADAPTER to the CHARGE CONTROLLER port

labeled BATTERY on the Solar Collector.

4.

Connect your device’s 12V Vehicle Charger into the BARREL POWER ADAPTER and

the other end into your device.

5.

The LEDs on the CHARGE CONTROLLER and your 12V Vehicle Charger should be

illuminated.

6.

If your device will not charge, check that all connections are secure and there is

sufficient sunlight. Contact Aervoe for additional assistance if needed.

7.

Disconnect the Solar Collector when fully charged or not in use. Do not leave

unsupervised.

NOTE: User is responsible for confirming compatibility. Aervoe Industries, Inc. is not

responsible for damage to user’s device. Read and understand all operating instructions and

specifications prior to use.

Male MC4

Tip

Female MC4

Tip

Advertising
This manual is related to the following products: