American Time Remote Transmitter 5 Watt User Manual

Please read this first, Activate & hang your clocks, Sitesync iq

Advertising
background image

American Series Digital Clocks

1. Take the clock to the area where it will be used.

2. To activate the clock, connect to AC power.

3. Display will flash “U40” or 1:00 o’clock until it

receives a signal.

4. Verify synchronization takes place within 2-5

minutes

Your SiteSync IQ system is now set up for proper operation.

For information on other features, see the Installation and

Operation Manual that was included with your system. If you

have any questions, please contact Technical Support at

American Time:

800-328-8996

.

6

Activate & hang your clocks

Don't activate the battery or apply power to the clocks until the Remote Transmitter is installed and

transmitting and the clock is in the intended location.

SiteSync IQ

®

Remote Transmitter

with Magnetic Mount TX Antenna

INST-SSQRTM-N-E Rev 2

Please read this first!

After determining the proper wattage for your facility, we guarantee the coverage of your Remote
Transmitter when you follow a few simple steps. If this is your first installation or you have questions at
any time during this process, please call American Time toll free at

800-328-8996

.

We're here to help!

This Quick Start Guide will help you avoid three common installation mistakes:

1. Improper location of transmitting (TX) antenna.

A temporary install of the Remote Transmitter

is recommended.

Don't drill holes for permanent installation and mounting until the system is working correctly.

2. Improper Remote Transmitter start-up.

A successful transmission is indicated by the PTT and

DATA LED's flashing on the front of the unit.

Don't locate the magnetic mount TX antenna within 4' of the Remote Transmitter.

3. Improper clock start-up.

Activate clocks in their intended location.

Don't activate the clocks in one room and move them to another location as signal reception

will not be verified. Make sure the Remote Transmitter is transmitting and is not in Quiet Mode.

Important Note:

Clocks should be installed within 24 hours of installing the Remote Transmitter.

After 24 hours, the Remote Transmitter will enter Quiet Mode. To disable Quiet Mode, reference

the Remote Transmitter Installation and Operation Manual section Remote Transmitter Connect

Configuration tab step 5 and Appendix F.

AC

DC

To

wiring

box

Reset

Button

LED

Electric

Electric (AC) Analog Clocks

1. Take the clock to the area where it will be used.

2. To activate the clock, connect to AC power.

The LED on the back of the clock (see below)

will flash red within 30 seconds of power-up to

indicate receiver is looking for the wireless

signal.

When the signal is received, the LED will flash

green. Be patient. The clock hands will rapid

advance to the correct time. This may take

up to 15 minutes.

3. Hang the clock once signal reception is

verified and clock is operating correctly.

Note: If the LED does not flash within 30 seconds,

disconnect the barrel plug on the clock receiver, wait

10 seconds and reconnect. The LED will begin flashing

within 30 seconds.

Activation Note:

Clocks should be installed within 24 hours of

installing the Remote Transmitter. After 24 hours, the Remote

Transmitter will enter Quiet Mode. To disable Quiet Mode

reference the Remote Transmitter installation and Operation

Manual section Remote Transmitter Connect Configuration tab

step 5 and Appendix F.

phone:

800-328-8996

fax:

800-789-1882

online:

american-time.com

mail:

140 3rd St. So.; PO Box 707, Dassel, MN 55325-0707

AC

DC

To

wiring

box

LED

Battery

Barrel

Jack

Input

Battery Analog Clocks

1. Take the clock to the area where it will be

used.

2. To activate the clock, connect barrel jack plug

of battery pack to wireless receiver. The

LED on the back of the clock will flash red

within 30 seconds of power-up to indicate

receiver is looking for the wireless signal.

When the signal is received, the LED will flash

green. Be patient. The clock hands will rapid

advance to the correct time. This may take up

to 15 minutes.

3. Hang the clock after hands are rapid

advancing.

Note: If the LED does not flash within 30 seconds,

remove the barrel jack plug of the battery pack from

the wireless receiver for 5 seconds and reconnect it.

This resets the receiver. The LED will begin flashing

within 30 seconds.

Advertising
This manual is related to the following products: