User Manual Pioneer - DEH-P6900IB

Recognized languages:   Deutsch   Español   Français   Italiano   English
Advertising
background image

Note:

Check all connections and systems before final
installation.

Do not use unauthorized parts. The use of
unauthorized parts may cause malfunctions.

Consult with your dealer if installation requires
drilling of holes or other modifications of the
vehicle.

Do not install this unit where:
— it may interfere with operation of the vehicle.
— it may cause injury to a passenger as a result

of a sudden stop.

The semiconductor laser will be damaged if it
overheats. Install this unit away from hot places
such as near the heater outlet.

Optimum performance is obtained when the unit
is installed at an angle of less than 60°.

DIN Front/Rear-mount

This unit can be properly installed either from
“Front” (conventional DIN Front-mount) or
“Rear” (DIN Rear-mount installation, utilizing
threaded screw holes at the sides of unit chassis).
For details, refer to the following installation
methods.

DIN Front-mount

Installation with the rubber bush

1. Insert the mounting sleeve into the dashboard.

When installing in a shallow space, use a sup-
plied mounting sleeve. If there is enough
space behind the unit, use factory supplied
mounting sleeve.

2. Secure the mounting sleeve by using a screwdriv-

er to bend the metal tabs (90°) into place.

3. Install the unit as illustrated.

Removing the Unit

1. Extend top and bottom of the trim ring outwards

to remove the trim ring. When reattaching the
trim ring, push the trim ring onto the unit until it
clicks. (If the trim ring is attached upside down,
the trim ring will not fit properly.)

It becomes easy to remove the trim ring if the
front panel is released.

2. Insert the supplied extraction keys into both sides

of the unit until they click into place.

3. Pull the unit out of the dashboard.

53

53

1

1

182

182

60

°

Installation

ENGLISH

INST

ALLA

TION MANUAL

MANUEL D’INST

ALLA

TION

<KMMNX> <06J00000>

DEH-P6900IB

Printed in Thailand
Imprimé en Thaïlande

<XRD7139-A/N> EW

This product conforms to new cord colors.
Los colores de los cables de este producto se confor-
man con un nuevo código de colores.
Dieses Produkt entspricht den neuen Kabelfarben.
Le code de couleur des câbles utilisé pour ce produit
est nouveau.
Questo prodotto è conforme ai nuovi codici colori.
De kleuren van de snoeren van dit toestel zijn gewijzigd.
С‡ММУВ ЫТЪУИТЪ‚У ТУУЪ‚ВЪТЪ‚ЫВЪ МУ‚˚П
ЪВ·У‚‡ÌËflÏ Í ˆ‚ВЪЫ ФУ‚У‰У‚.

Trim ring

DIN Rear-mount

1. Extend top and bottom of the trim ring outwards

to remove the trim ring. When reattaching the
trim ring, push the trim ring onto the unit until it
clicks. (If the trim ring is attached upside down,
the trim ring will not fit properly.)

It becomes easy to remove the trim ring if the
front panel is released.

2. Determine the appropriate position where the

holes on the bracket and the side of the unit
match.

3. Tighten two screws on each side.

Use either truss screws (5 mm

× 8 mm) or

flush surface screws (5 mm

× 9 mm), depend-

ing on the shape of screw holes in the
bracket.

Fastening the front panel

If you do not plan to detach the front panel, the
front panel can be fastened with supplied screws
and holders.

1. Attach the holders to both sides of the front

panel.

2. Replace the front panel to the unit.

3. Flip the holders into upright positions.

4. Fix the front panel to the unit using screws.

Trim ring

Screw

Dashboard or Console

Factory radio mounting bracket

Rubber bush

Screw

Dashboard

Mounting sleeve

Screw

Holder

Advertising