Connecting the units english, Connection diagram – Pioneer DEH-P6900IB User Manual

Page 5

Advertising
background image

Note:

When this unit is installed in a vehicle without
ACC (accessory) position on the ignition switch,
red cable must be wired to the terminal that can
detect the operation of the ignition key.
Otherwise, battery drain may result.

Use this unit in other than the following condi-
tions could result in fire or malfunction.
— Vehicles with a 12-volt battery and negative

grounding.

— Speakers with 50 W (output value) and 4 ohm

to 8 ohm (impedance value).

To prevent short-circuit, overheating or malfunc-
tion, be sure to follow the directions below.
— Disconnect the negative terminal of the bat-

tery before installation.

— Secure the wiring with cable clamps or adhe-

sive tape. To protect the wiring, wrap adhe-
sive tape around them where they lie against
metal parts.

— Place all cables away from moving parts,

such as gear shift and seat rails.

— Place all cables away from hot places, such as

near the heater outlet.

— Do not pass the yellow cable through a hole

into the engine compartment to connect to a
battery.

— Cover any disconnected cable connectors

with insulating tape.

— Do not shorten any cables.
— Never cut the insulation of the power cable of

this unit in order to share the power to other
equipment. Current capacity of the cable is
limited.

— Use a fuse of the rating prescribed.
— Never wire the speaker negative cable directly

to ground.

— Never band together multiple speaker’s nega-

tive cables.

Control signal is output through blue/white cable
when this unit is powered on. Connect it to an
external power amp’s system remote control or
the vehicle’s auto-antenna relay control terminal
(max. 300 mA, 12 V DC). If the vehicle is
equipped with a glass antenna, connect it to the
antenna booster power supply terminal.

Never connect blue/white cable to external power
amp’s power terminal. Also, never connect it to
the power terminal of the auto antenna.
Otherwise, battery drain or malfunction may
result.

IP-BUS connectors are color-coded. Be sure to
connect connectors of the same color.

Black cable is ground. This cable and other prod-
uct’s ground cable (especially, high-current prod-
ucts such as power amp) must be wired separate-
ly. Otherwise, fire or malfunction may result if
they are accidentally detached.

Cord function may differ according to the
product, even if cord color is the same. When
connecting this system, be sure to check all
manuals and connect cords correctly.

No ACC position

ACC position

ON

S

T

A

R

T

O

FF

ACC

ON

S

T

A

R

T

O

FF

+

+

+

+

+

+

33. Power amp

(sold separately)

39. Subwoofer

1*

3*

2*

4*

5*

17. Note:

Depending on the kind of vehicle,
the function of 3* and 5* may be
different. In this case, be sure to
connect 2* to 5* and 4* to 3*.

18. Connect leads of the same

color to each other.

19. Cap (1*)

Do not remove cap
if this terminal is
not in use.

20. Yellow (3*)
Back-up

(or

accessory)

22. Red (5*)
Accessory

(or back-up)

21. Yellow (2*)

Connect to the constant
12 V supply terminal.

23. Red (4*)

Connect to terminal controlled
by ignition switch (12 V DC).

24. Orange/white

Connect to lighting switch terminal.

26. ISO connector

Note:
In some vehicles, the ISO connector may
be divided into two. In this case, be sure
to connect to both connectors.

31. Speaker leads
White:

Front

left

+

White/black:

Front

left

Gray:

Front

right

+

Gray/black:

Front

right

Green:

Rear

left

+ or subwoofer +

Green/black:

Rear

left

≠ or subwoofer ≠

Violet:

Rear

right

+ or subwoofer +

Violet/black:

Rear

right

≠ or subwoofer ≠

32. Connect with RCA cables

(sold separately)

28. Blue/white

Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).

29. Blue/white (7*)

Connect to auto-antenna relay control
terminal (max. 300 mA 12 V DC).

The pin position of the ISO connector will
differ depends on the type of vehicle. Connect
6* and 7* when Pin 5 is an antenna control
type. In another type of vehicle, never connect
6* and 7*.

38. Rear speaker

40. Perform these connections when

using the optional amplifier.

41. Notes:

• Change the initial setting of this unit (refer to the Operation

Manual). The subwoofer output of this unit is monaural.

• When using a subwoofer of 70 W (2

Ω) , be sure to connect

with Violet and Violet/black leads of this unit. Do not connect
anything with Green and Green/black leads.

27. Yellow/black

If you use an equipment with Mute
function, wire this lead to the Audio
Mute lead on that equipment. If not,
keep the Audio Mute lead free of any
connections.

Use a stereo mini plug cable
to connect with auxiliary
equipment.

25. Black (chassis ground)

Connect to a clean, paint-free metal location.

1. iPod with Dock

Connector

3. Dock connector port

2. Dock connector

4. Interface cable (e.g., CD-I200)

(sold separately)

2 m

6. This product

7. Rear output

8. Front output

9. Antenna jack

10. Subwoofer output

11. Fuse (10 A)

12. AUX jack (3.5 ø)

13. Wired remote input

Hard-wired remote control
adaptor can be connected
(sold separately).

14. IP-BUS

input (Blue)

15. IP-BUS cable

16. Multi-CD player

(sold separately)

33. Power amp

(sold separately)

33. Power amp

(sold separately)

34. System remote control

30. Blue/white (6*)

35. Front speaker

35. Front speaker

36. Left

37. Right

38. Rear speaker

39. Subwoofer

15 cm

5. Gray

Connecting the Units

ENGLISH

Connection Diagram

1. iPod with Dock Connector
2. Dock connector
3. Dock connector port
4. Interface cable (e.g., CD-I200) (sold separately)
5. Gray
6. This product
7. Rear output
8. Front output
9. Antenna jack
10. Subwoofer output
11. Fuse (10 A)
12. AUX jack (3.5 ø)

Use a stereo mini plug cable to connect with
auxiliary equipment.

13. Wired remote input

Hard-wired remote control adaptor can be con-
nected (sold separately).

14. IP-BUS input (Blue)
15. IP-BUS cable
16. Multi-CD player (sold separately)
17. Note:

Depending on the kind of vehicle, the function of
3* and 5* may be different. In this case, be sure
to connect 2* to 5* and 4* to 3*.

18. Connect leads of the same color to each other.
19. Cap (1*)

Do not remove cap if this terminal is not in use.

20. Yellow (3*)

Back-up (or accessory)

21. Yellow (2*)

Connect to the constant 12 V supply terminal.

22. Red (5*)

Accessory (or back-up)

23. Red (4*)

Connect to terminal controlled by ignition switch
(12 V DC).

24. Orange/white

Connect to lighting switch terminal.

25. Black (chassis ground)

Connect to a clean, paint-free metal location.

26. ISO connector

Note:
In some vehicles, the ISO connector may be
divided into two. In this case, be sure to connect
to both connectors.

27. Yellow/black

If you use an equipment with Mute function,
wire this lead to the Audio Mute lead on that
equipment. If not, keep the Audio Mute lead free
of any connections.

28. Blue/white

Connect to system control terminal of the power
amp (max. 300 mA 12 V DC).

29. Blue/white (7*)

Connect to auto-antenna relay control terminal
(max. 300 mA 12 V DC).

30. Blue/white (6*)

The pin position of the ISO connector will differ
depends on the type of vehicle. Connect 6* and
7* when Pin 5 is an antenna control type. In
another type of vehicle, never connect 6* and 7*.

31. Speaker leads

White:

Front left +

White/black: Front left ≠
Gray:

Front right +

Gray/black:

Front right ≠

Green:

Rear left + or subwoofer +

Green/black: Rear left ≠ or subwoofer ≠
Violet:

Rear right + or subwoofer +

Violet/black: Rear right ≠ or subwoofer ≠

32. Connect with RCA cables (sold separately)
33. Power amp (sold separately)
34. System remote control
35. Front Speaker
36. Left
37. Right
38. Rear Speaker
39. Subwoofer
40. Perform these connections when using the

optional amplifier.

41. Notes:

• Change the initial setting of this unit (refer to

the Operation Manual). The subwoofer output
of this unit is monaural.

• When using a subwoofer of 70 W (2

Ω), be

sure to connect with Violet and Violet/black
leads of this unit. Do not connect anything with
Green and Green/black leads.

Advertising