Kleenmaid LWK320 User Manual

Lwk320 ironing centre kit set

Advertising
background image

107843 Issue B
ECN: 04097

Note: Generic model is shown.
Actual product may differ.

SPECIFICATION DIAGRAM
Model
LWK320

(Dimensions in mm)

I N S T A L L A T I O N I N S T R U C T I O N

PLEASE READ THE ENTIRE INSTRUCTION BEFORE INSTALLING THE LWK320 IRONING CENTRE KIT SET

1. Disconnect LWK320 Ironing Centre Kit Set Console from power supply.
(Ensure the power is switched off)

2. Insert small screwdriver or slim knife as shown, ease
catch to side and slip out diffuser.

3. Replace lamp (40 watt max.)

4. Slide diffuser back into aperture and “click” into place.
(Turn power back on)

An external ON/Off safety power socket must be installed inside the wall
behind the cabinet. Plug the console into the socket.
Alternatively the unit can be hard wired directly to an isolation
switch by an electrician. The plug or switch must remain accessible
after the installation.

LWK320 Ironing Centre Kit Set

NOTE: The LWK320 Ironing Centre Kit Set is designed to fit a 400mm wide, (368mm Internal,kitchen /
laundry cabinet. Please ensure your cabinet fits the following dimensions as shown on the next page.
NOTE: Please take care when predrilling holes not to drill all the way through or damage the cabinet.
The screws supplied with all kits are designed for 16mm thick cabinet panels. Different screws may
be needed if the cabinet panels are less than 16mm thick.

CONSOLE INSTALLATION

1. Drill the 50mm hole in the top cabinet face for the electrical cable (Diagram C).
If through sheetmetal the 50mm hole needs deburring.
2. Remove diffuser from console using a slim knife or flat bladed screw driver (Diagram D).
3. Remove Lamp (Bayanet Cap).
4. Position the console on the top cabinet face with the diffuser removed. Mark out the 3 mounting hole
positions on the cabinet face or alternatively use the dimension provided to pre-drill the 3
mounting holes (Diagram B).
5. Drill out the 3 marked holes for the supplied screws.
6. Feed the electrical cable through the 50mm hole. Position the console with the 3 mounting holes.
Using the supplied screws attach the console to the top cabinet face.
6. Replace lamp.
7. Slide diffuser back into aperture and “click” into place.

CONNECTING THE CONSOLE TO ELECTRIC POWER

Pivot Rod

Back Stop

Pivot Stop

BOARD INSTALLATION

Installation Kit Includes

- 2 x Board retainer Screws

- 16 x Ironing Board Screws

- 3 x Console Screws

E

D

Top Cabinet

Face

Console

Mounting

Holes

C

91

15

170

105

40

A

Front of
Cabinet

L A M P R E P L A C E M E N T

150*

400*

150

16*

40

82.5

35

86.5

50

B

Centered

368

1. Pre-drill holes in the cabinet on both sides 3.0mm, for the
screws supplied as per diagram ‘A’.
2. Attach one (1) height adjustment bracket to the cabinet using the screws supplied.
3. Insert the ironing board pivot rod and pivot stop into the attached
bracket. While supporting the ironing board attach the other bracket
to both the pivot rod and pivot stop (Diagram E).
4. Move the board into position so the free bracket lines up with the pre-drilled holes and
secure using the supplied screws.
5. Position the back stop behind the pivot stop in the middle of the cabinet and mark out hole position.
Drill 4 holes, 3.0mm, for the screws supplied. Attach the back stop (Diagram E).
6. The board retainer is to be positioned as shown on the first page (Diagram F). Mark out the screw
holes and drill 2.5mm for the supplied screws.
7. Attach board retainer.
8. Fit the board cover with the silver/gray coating facing up.

600*

154

165

2100*

1630

680

A

* Recommended / typical dimensions.

366

12

6

91

165

366

100

192

1125

295

310

395

675

150

Board Retainer

Console

Ironing Board

F

Diagram

Should you be fitting a door to the enclosure holding this LWK320 Ironing Centre Kit Set, please
be mindful of the position of all door furniture (hinges, handles, etc.) Specifically ensure the
board will operate without obstruction.

Advertising