OpenEye CM-170 User Manual

Regulatory compliance general specifications, Camera adjustments, 170 series outdoor dome

Advertising
background image

Quick Installation Sheet

CM-170

model no

.

Please carefully read these instructions before using this product.

Save this manual for future use.

28550AA

170 Series Outdoor Dome

RoHS

FCC COMPLIANCE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against armful interference in a residential
installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced Radio/TV technician for help.

CISPR 22 WARNING:

This is a Class B product. In a domestic environment this product may cause radio interference in which case the user
may be required to take adequate measures.
POWER SUPPLY REQUIREMENTS:
For use with listed Audio/Video product and only connected to 15W or less power supply.
*Power supply should be a NEC Class 2 / LPS Supply.

EQUIPMENT MODIFICATION CAUTION:

Equipment changes or modifications not expressly approved by seller.
The party responsible for FCC compliance could void the user’s authority to operate the equipment and could create a
hazardous condition.

This class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

FCC part 15 Class B
CE: EN55011
ICES-003
EN55022
CISPR 11
CISPR 22
ANSI C63.4
CE: EN50130-4

Emissions

Immunity

CM-170

Type / Format

Scanning Element

Image Picture Element
Effective Picture Element
Resolution (TV Lines)
Minimum Illumination
S/N Ratio
Back Light Compensation
Exposure Control
Sync System
Gamma Compensation
Video Output
White Balance
Auto White Balance Range
Power Range*
Power Consumption
Operating Temperature
Storage Temperature

NTSC

2:1 Interlace,

H15.734KHz/V :59.9Hz

1/3” Interline CCD

768 (H) X 494 (V)

480

1.2 Lux @ F1.6

48dB

Central Area for DC IRIS Lens

DV Type Auto IRIS Control

INT

0.45

1.0Vpp, 75

Ω

Unbalanced

Automatic White Balance

2500

°

K --9700

°

K

DC 12V

±10%

2.2W (Max)

-10

°C ~ +50°C

-20

°C ~ +60°C

Model No.

Regulatory Compliance

General Specifications

Hardware Kit Contents

Lens Specifications

A1 : Focus Adjuster
A2 : Field of View Adjuster

A1

A2

A3

TILT 90°

ROTATE 360°

PAN 360°

Angle Adjustment

Do Not Overturn

B1 : Function Control Dip Switches

B2 : AI Level Adjustment*

*AI Level Adjustment is factory set and hould not normally require adjustment.

Switch 2

ON

OFF

Back Light Compensation

Auto Gain Control

OFF

(Normal Mode)

ON

(Turbo Mode)

Switch 1

Camera Adjustments

Function Control Dip Switches

• 1/2” Rubber Grommet
• 3/4” Rubber Grommet
• Screw Pack
• Torx Driver
• Wire-Ended Power Adaptor Lead
• Quick Install Adaptor

Focal Length
F-No.
Iris Range
Minimum Object Distance

Field of View

BLC
AGC-UP
Low Light Croma Suppression

4mm~9mm

F1.6

F1.6~F2.4

50cm (19.7”)

92.8°~39.4°
71.0°~31.6°
51.6°~23.6°

ON/OFF
ON/OFF

AUTO

Diagonal
Horizontal
Vertical

T1

T2

Template

Cable Access Using Base Cable Entry

Surface Mount (wall or ceiling)

Using Quick Install Adaptor:

Using Locking Arms:

Using Screws:

Cable Access

T1

T1

T1

T5

T5

T3

US Single Gang Box

US Single Gang Box

T4

3/4” NPT

Cut a 1.5” (38mm) hole in the mounting surface as
indicated by T2. The hole can also be used for
cable access.

Cut a 4.3” (110mm) hole in the mounting surface as
indicated by T3. The hole can also be used for
cable access.

Drill four holes at template positions T1 and use the
screws and anchors provided in the screw kit if they
are appropriate for the mounting surface.

When mounting the camera on a surface with the
provided screws, use one of the side knock-outs, as
indicated on the template, for cable entry.

To thread the cables through the mounting
surface, cut a 3/4” (19mm) hole as
indicated by T4.

Note:

When mounting on a US Single Gang Box,

use the pre-drilled holes in the dome base as
indicated by T5.

Advertising