Posiflex SD-666W - Manual

Page 1 / 2
SD-660/SD-666 SERIES
UPGRADE KIT
USER’S MANUAL
Rev. : A0
I. FEATURES
Upgrade kit for fan free touch terminals Jiva KS series
Optional iButton (Dallas key) reader
Options for MSR heads covering ISO single head & dual head or JIS I/II
3 tracks type MSR can read also AAMVA and CA DMV card
Magnetic Stripe Reader in USB full speed HID interface
Total power consumption: 300 mA @ 5V DC through proprietary USB port
FCC NOTICE
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual,
may cause interference to radio communications. It has been tested and found to comply with limits for a Class A digital device pursuant to subpart J of Part
15 of FCC Rules, which are designed to provide reasonable protection against interference when operated in a commercial environment. Operation of this
equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures to correct
the interference.
WARRANTY LIMITS
Warranty will terminate automatically when the equipment is opened by any person other than the authorized technicians. The user should consult
his/her dealer for the problem happened. Warranty voids if the user does not follow the instructions in application of this merchandise. The manufacturer is by
no means responsible for any damage or hazard caused by improper application.
The hardware utility program, including instructions for its use, is provided “AS IS” without warranty of any kind. Posiflex Technology, Inc. further
disclaims all implied warranties including without limitation any implied warranties of merchantability or of fitness for a particular purpose. the entire risk
arising out of the use or performance of the software and documentation remains with you.
ABOUT THIS MANUAL
This manual is written in an attempt with full strength to assist the user to utilize the upgrade kit SD-660/SD-666 for the Posiflex fan free touch
terminals Jiva KS systems. This series of products incorporate 2 delicately designed POS peripherals each can be used as an excellent tool to accommodate
the required security specially involved in POS business, kiosk and hospitality operation. This manual covers the conceptual and operational aspects of these
units. For technical aspects involving opening of the unit or option implementation, it is only available to the authorized distributors.
The manufacturer of the SD-660/SD-666 series heartily apologizes to the user for reserving the right to change or to modify this manual without
notice due to the rapid and constant progress and improvement on science and technology. The user may always obtain the most up to date information
through any of our web sites: http://www.posiflex.com or http://www.posiflex.com.tw.
 Copyright Posiflex Technology, Inc. 2013
All rights are strictly reserved. No part of this documentation may be reproduced, stored in a retrieval system, or transmitted in any form or by any
means, electronic, mechanical, photocopying, or otherwise, without the prior written consent of Posiflex Technology, Inc. the publisher of this documentation
TRADE MARKS AND SERVICE MARKS
POSIFLEX is a registered trademark of Posiflex Technology, Inc. an ISO-9001 and ISO-14001 certified manufacturer.
Other brand and product names are trademarks and registered trademarks and service marks of their respective owners.
II. INSTALLATION
1. HARDWARE INSTALLATION
For SD-660/SD-666 series ordered with the host system KS series, it is installed on the
system at delivery. For separately ordered SD-660/SD-666 series, it is delivered separately
from the system and needs to be fixed onto the system per following instructions before use.
You may find two screw holes on back of the right side of the main unit of
Jiva KS series. Remove these 2 screws to remove the cover for side
mount upgrade kit. Take out the cable inside this cover as circled in
right picture and connect it to connector inside the side mount upgrade
kit SD-660/SD-666 as arrowed in same picture. Gently arrange the excessive
length of this cable back in the hole and use the 2 original screws to fit
SD-660/SD-666 back to the position originally occupied by the cover if the
SD-660/SD-666 is not installed with the iButton reader (the circular marked cables would be
present). Connection of this would not be necessary if the SD-660/SD-666 contains only the
iButton reader (no MSR and no audio ports). Please reserve the cover if there is chance to have
the side mount kit removed in the future.
When the SD-660/SD-666 is installed with iButton receptor, there will be 2 additional
cables (marked with a circle in the above picture) coming out of the bottom side of SD-
660/SD-666. Connect the longer to the DB9 COM ports for iButton reader setup (and data
connection). Connect the shorter cable through a USB-PS/2 conversion cable as arrowed in the
left picture to one of the USB ports inside cable cover area. Route the cables through the side
opening of the cable cover on KS series as
illustrated in the right picture and close the cable
cover. This paragraph of operations won’t be
required if iButton reader is not installed on SD-
660/SD-666.
P/N: 19850904020