Fp_led_rev040210 (4), Fp series, Fp-light | light settings and controls – Soundtube FP6020-II User Manual

Page 4

Advertising
background image

FP-Light | Light Settings and Controls

Module Description

The LED light can operate as a

standard light fixture or can be

triggered with the FP-Motion

module. Brightness can be

controlled either internally with

an adjustment on the FP-Light

module or externally with a

global system controller. To

trigger the FP-Light with the

FP-Motion, refer to Section 3

and the FP-Motion installation

instructions.

Section 1 – Wiring The

Speaker

Connecting The External

Power Supply

The FP-Light requires an

external power supply rated

between 12 V and 18 V

(optional SoundTube

accessories: AC-PS-1530 and

AC-PS-1550). Connect the

power supply to the

brown/white (+) and brown (-)

wires in the Cat 5 cable.

Section 2 – Adjusting the

Brightness

Remove The Pod Cover

Remove the pod cover [1] from

the FP pod [2] by loosening the

two captured screws [3] on

each side (Figure 1). The

screws will not come out of the

cover.

Adjust The Brightness

Internally

To manually adjust the

brightness of the light use a

small screwdriver to turn the

trim pot on the upper right

corner of the light module [6].

Turning the trim pot clockwise

will increase brightness and

counterclockwise will decrease

brightness.

Adjust The Brightness

Externally

The external brightness control

is disabled by factory default.

To enable the external

brightness control, move

Jumper 4 [4] on the upper left

corner of the FP Light module

to the enabled position over

the two right pins (Figure 2).

To adjust the brightness

externally, incorporate a

controller such as Crestron or

Lutron and connect the

positive lead [+] from the

controller to the orange/white

wire in the Cat 5, and the

negative lead [–] from the

controller to the orange wire in

the Cat 5. The Light module

accepts 0 V to 10 V DC signal

to control the brightness. To

achieve maximum

brightness, the trim pot

must be turned fully

clockwise (see previous

step).

Section 3 – Motion Sensor

Triggering

Enable The Motion Sensor

Note: To use with motion

triggering, both the FP-Light

and the FP-Motion modules

must be installed.

Since motion sensing is

disabled by factory default, the

light will be on continuously

when power is supplied. To

enable motion sensor

triggering of the light, move

Jumper 2 [5] on the lower left

corner of the FP-Light module

to the two left pins (Figure 3).

When this feature is enabled,

the light will only activate when

motion is detected. See

FP-Motion sensor instructions

for settings and controls.

Section 4 – Replacing The

Pod Cover

Replace pod cover [1] and

tighten screws [3].

Power

External Controller

LED Light

Amp Control

Speaker

Contact closure = Green/White

Contact closure = Green

12 V trigger = Blue/White

Amp control = Blue

LED control = Orange/White

LED control = Orange

Amp gain = Blue

Amp gain = Orange

Left in = White

Left in = Green
Right in = Red

Right in = Black

Power = Brown/White

Power ground = Brown

Cat 5 Wiring

All signal and control wires are located in the signal/hanging cable provided

with the FP unit speaker wires. A Cat 5 cable (blue shield) contains the control and power

wires; audio wires are individual 16-gauge wires in the bundle.

Wiring Instructions

1 FP-Light module
2 Jumpers

Contents

Figure 2

Figure 3

FP pod [2]

Brightness control [6]

Pod cover [1]

Light module

Main electrical board

LED lamp baffle

(ships with light module only)

FP modules ship pre-installed

from the factory.

Other FP Series optional

modules include:

1. FP-Motion
2. FP-ScentAir
3. FP-Amp

All modules require a power source.

An optional 15-volt source is

available from SoundTube
(Model numbers: AC-PS-1530

or AC-PS-1550).

Jumper 4 (J4) external

brightness control [4]

Light connection

Jumper 2 (J2) motion

sensor control [5]

Pod cover screws [3]

Figure 1

FP Series

Do not spec or install speaker near support beam, ventilation duct or
other structure that may interfere with speaker function or dispersion.

Warning

© 2010 SoundTube Entertainment, Inc. All rights reserved. PN INS-FP-LIGHT Rev04.02.10

Warning

SoundTube speakers must be installed by a professional audio installer/contractor. For safety and for
optimum audio performance, installer must follow all directions issued by SoundTube Entertainment.

1.435.647.9555

|

800.647.TUBE

|

www.soundtube.com

435.647.9555

|

800.647.TUBE

|

www.soundtube.com

Install Instructions For:

FP-Light

FP Series

435.647.9555

|

800.647.TUBE

|

www.soundtube.com

Install Instructions For:

FP-Light

FP Series

Advertising
This manual is related to the following products: