Space Ray LTS Series Two Stage - Manual (Page 34)

Form #43155040
May 2013
-33-
* Available as Accessories
KEY DIMENSIONS AND COMPONENTS OF THE GAS CONNECTIONS
14 to 17”
(36 to 43cm)
Approved
Flexible Connector
*Second Stage Regulator with
Vent Leak Limiter to reduce the
Supply Pressure below 14” W.C.
Gas Pressure
= 2 PSIG
Gas Supply
Piping
Sediment Trap
(Drip Leg)
*Manual Gas
Shut Off Valve
Control Box Movement
2” (5cm) Max.
Displacement
END VIEW
Control Box
SIDE VIEW
Movement
Alternate Supply
Locations
Adaptor 1/2” NPT male
Adaptor 1/2” NPT female
INCORRECT POSITIONS
Movement
WRONG
Movement
WRONG
Movement
WRONG
Movement
WRONG
US ONLY US ONLY US ONLY US ONLY: : : : Connector MUST be installed in “ Connector MUST be installed in “ Connector MUST be installed in “ Connector MUST be installed in “⊃ ⊃ ⊃ ⊃” configuration. Use only ” configuration. Use only ” configuration. Use only ” configuration. Use only
the 36” long connector that was furnished with this heater. the 36” long connector that was furnished with this heater. the 36” long connector that was furnished with this heater. the 36” long connector that was furnished with this heater.
US ONLY: A gas connector certified for use on a tu A gas connector certified for use on a tu A gas connector certified for use on a tu A gas connector certified for use on a tubular type infrared heater per the standard for Connectors bular type infrared heater per the standard for Connectors bular type infrared heater per the standard for Connectors bular type infrared heater per the standard for Connectors
for Gas Appliances, ANSI Z21.24/CSA 6.10 is supplied for installation in US only. The gas connector is 36” long for Gas Appliances, ANSI Z21.24/CSA 6.10 is supplied for installation in US only. The gas connector is 36” long for Gas Appliances, ANSI Z21.24/CSA 6.10 is supplied for installation in US only. The gas connector is 36” long for Gas Appliances, ANSI Z21.24/CSA 6.10 is supplied for installation in US only. The gas connector is 36” long
and
and and and 1 1 1 1/ // /2 2 2 2” nominal ID, and must be installed as shown above, in ” nominal ID, and must be installed as shown above, in ” nominal ID, and must be installed as shown above, in ” nominal ID, and must be installed as shown above, in one plane, and without one plane, and without one plane, and without one plane, and without sharp bends, kinks or sharp bends, kinks or sharp bends, kinks or sharp bends, kinks or
twists. twists. twists. twists.
CANADA ONLY: A Type I hose connector should be used that is certified as being in compliance with the A Type I hose connector should be used that is certified as being in compliance with the A Type I hose connector should be used that is certified as being in compliance with the A Type I hose connector should be used that is certified as being in compliance with the
Standard for Elastomeric Composite Hose and Hose Couplings for Conducting Propane and Natural Gas Standard for Elastomeric Composite Hose and Hose Couplings for Conducting Propane and Natural Gas Standard for Elastomeric Composite Hose and Hose Couplings for Conducting Propane and Natural Gas Standard for Elastomeric Composite Hose and Hose Couplings for Conducting Propane and Natural Gas
(CAN/CGA 8.1) and is of l
(CAN/CGA 8.1) and is of l (CAN/CGA 8.1) and is of l (CAN/CGA 8.1) and is of length of 36+/ ength of 36+/ ength of 36+/ ength of 36+/---- 6 in (90+/ 6 in (90+/ 6 in (90+/ 6 in (90+/---- 15 cm). 15 cm). 15 cm). 15 cm). The gas connector The gas connector The gas connector The gas connector must be installed as shown must be installed as shown must be installed as shown must be installed as shown
above above above above, in one plane, and without sharp bends, kinks or twists. , in one plane, and without sharp bends, kinks or twists. , in one plane, and without sharp bends, kinks or twists. , in one plane, and without sharp bends, kinks or twists.