Document Outline

• FRONT MATTER
• CONTENTS
• INTRODUCTION
  • Optional Equipment
  • Software
  • How to Use This Manual
  • Where to Get Help
• CHAP 1-SETTING UP YOUR SYSTEM
  • Preparing to Set Up the System
  • Installation Oveview
  • Installing Optional Equipment
  • Connecting Peripheral Devices
  • Turning On the Computer
  • Running the Change Country Code Utility
    • Setting the Country Code for the first Time
    • Changing the Country Code
• CHAP 2-RUNNING SYSTEM CONFIGURATION
  • How to Use This Chapter
  • The Configuration Process
    • Using Configuration Files
    • Using the Keyboard
    • Using a Mouse
    • Using On-line Help
  • Configuring Your System
    • Program
    • Setting the Date and Time
    • Performing the Configuration Steps
    • Adding or Removing a Board
    • Defining the Configuration Settings
    • Using Advanced Configuration Options
  • Using Alternate Configuration Files
    • Creating an Alternate SCI File
    • Loading an Alternate SCI File
  • Using Special Modes
    • Using the SD Command
    • Using the CF Command
    • Copying the Configuration Files to a Hard Disk
• CHAP 3-USING YOUR COMPUTER
  • Locking the Computer’s Cover
  • a Power-on Password
    • Changing or Deleting a Password
    • Using in Network Server Mode
  • Changing the Processor Speed
    • Entering Keyboard Commands
    • Using the ESPEED Program
  • Parking the Hard Disk Drive Heads
• CHAP 4-ACCESSING INTERNAL COMPONENTS
  • Special Precautions
  • Removing the Cover
  • Removing the Front Panel
  • Removing the Subassembly
  • Replacing the Subassembly
  • Replacing the Front Panel
  • Replacing the Cover
  • Post-installation Setup Procedures
• CHAP 5-INSTALLING AND REMOVING OPTIONS
  • Main System Board Map
  • Processor Board Maps
  • Option Cards
    • Installing Option Cards
    • Removing Option Cards
    • Removing the Processor Board
    • Installing the Processor Board
  • Math Coprocessor
    • Installing a Math Coprocessor
    • Removing a Math Coprocessor
  • Memory Modules
    • Installing Memory Modules
    • Removing Memory Modules
• CHAP 6-INSTALLING AND REMOVING DRIVES
  • Using the Correct Drive Bay
  • Setting the IDE Hard Disk Drive Jumpers
    • Changing the Jumper Settings
  • Installing or Removing a Drive in the External Bay
    • Installing a Drive
    • Removing a Drive
  • Installing or Removing a Drive in the Internal Bay
    • Removing a Drive
    • Installing Drive
    • Connecting the Cables
• APPENDIX A-RUNNING SYSTEM DIAGNOSTICS
  • Starting the Program
    • Deleting Tests
    • Adding Tests
  • Running Tests
    • Resuming From an Error
  • System Diagnostic Tests
  • Error Messages
• APPENDIX B-FORMATTING A HARD DISK
  • Starting the Program
    • Formatting a New Disk
    • Reformatting a Used Disk
    • Selecting an Option
    • Starting the Formatting Process
  • Option 1, Format
    • Modifying the Defective Track Table
    • Formatting the Disk
  • Option 2, Destructive Surface Analysis
  • Option 3, Non-destructive Surface Analysis
  • Exiting the Program
• APPENDIX C-TROUBLESHOOTING
  • Identifying Your System
  • Error Messages
  • Power or Lock-up Problems
  • Password Problems
  • Keyboard Problems
  • Monitor Problems
  • Diskette Problems
  • Diskette Drive Problems
  • Hard Disk Problems
  • Software Problems
  • Printer Problems
  • Option Card Problems
  • Memory Module Problems
  • Mouse Problems
  • Math Coprocessor Problems
• APPENDIX D-SPECIFICATIONS
  • Main System Board
  • Interfaces
  • Controllers
  • Processor Board
  • Mass Storage Bays
  • Power Supply
  • Keyboard
  • Environmental Requirements
  • Physical Characteristics
  • Power Source Requirements
  • System Memory Map
• GLOSSARY
• INDEX