H3C Technologies H3C WX3000E Series Wireless Switches User Manual
Switching engine layer 3 configuration guide
Advertising
This manual is related to the following products:
H3C WX5500E Series Access Controllers, H3C WX3500E Series Access Controllers, H3C WX2500E Series Access Controllers, H3C WX6000 Series Access Controllers, H3C WX5000 Series Access Controllers, H3C LSWM1WCM10 Access Controller Module, H3C LSUM3WCMD0 Access Controller Module, H3C LSUM1WCME0 Access Controller Module, H3C LSWM1WCM20 Access Controller Module, H3C LSQM1WCMB0 Access Controller Module, H3C LSRM1WCM2A1 Access Controller Module, H3C LSBM1WCM2A0 Access Controller Module, H3C WA3600 Series Access Points, H3C WA2600 Series WLAN Access Points
Table of contents
Document Outline
- Title Page
- Preface
- Contents
- ARP configuration
- Gratuitous ARP configuration
- IP addressing configuration
- DHCP overview
- DHCP server configuration
- Introduction to DHCP server
- DHCP server configuration task list
- Configuring an address pool for the DHCP server
- Configuration task list
- Creating a DHCP address pool
- Configuring address allocation mode for a common address pool
- Configuring dynamic address allocation for an extended address pool
- Configuring a domain name suffix for the client
- Configuring DNS servers for the client
- Configuring WINS servers and NetBIOS node type for the client
- Configuring BIMS server information for the client
- Configuring gateways for the client
- Configuring Option 184 parameters for the client with voice service
- Configuring the TFTP server and bootfile name for the client
- Configuring self-defined DHCP options
- Enabling DHCP
- Enabling the DHCP server on an interface
- Applying an extended address pool on an interface
- Configuring the DHCP server security functions
- Enabling handling of Option 82
- Specifying the threshold for sending trap messages
- Displaying and maintaining the DHCP server
- DHCP server configuration examples
- Troubleshooting DHCP server configuration
- DHCP relay agent configuration
- Introduction to DHCP relay agent
- DHCP relay agent configuration task list
- Enabling DHCP
- Enabling the DHCP relay agent on an interface
- Correlating a DHCP server group with a relay agent interface
- Configuring the DHCP relay agent security functions
- Enabling offline detection
- Configuring the DHCP relay agent to release an IP address
- Configuring the DHCP relay agent to support Option 82
- Displaying and maintaining the DHCP relay agent
- DHCP relay agent configuration examples
- Troubleshooting DHCP relay agent configuration
- DHCP client configuration
- DHCP snooping configuration
- DHCP snooping overview
- Configuring DHCP snooping basic functions
- Configuring DHCP snooping to support Option 82
- Configuring DHCP snooping entries backup
- Enabling DHCP starvation attack protection
- Enabling DHCP-REQUEST message attack protection
- Displaying and maintaining DHCP snooping
- DHCP snooping configuration examples
- BOOTP client configuration
- IPv4 DNS configuration
- IPv6 DNS configuration
- IP performance optimization configuration
- UDP helper configuration
- IPv6 basics configuration
- IPv6 overview
- IPv6 basics configuration task list
- Configuring basic IPv6 functions
- Configuring IPv6 ND
- Configuring PMTU discovery
- Configuring IPv6 TCP properties
- Configuring IPv6 FIB load sharing
- Configuring ICMPv6 packet sending
- Displaying and maintaining IPv6 basics configuration
- IPv6 basics configuration example
- Troubleshooting IPv6 basics configuration
- IP routing basics configuration
- Static routing configuration
- IPv6 static routing configuration
- RIP configuration
- RIP overview
- RIP configuration task list
- Configuring RIP basic functions
- Configuring RIP route control
- Tuning and optimizing RIP networks
- Configuring RIP timers
- Configuring split horizon and poison reverse
- Configuring the maximum number of load balanced routes
- Enabling zero field check on incoming RIPv1 messages
- Enabling source IP address check on incoming RIP updates
- Configuring RIPv2 message authentication
- Specifying a RIP neighbor
- Configuring RIP-to-MIB binding
- Configuring the RIP packet sending rate
- Displaying and maintaining RIP
- RIP configuration examples
- Troubleshooting RIP
- RIPng configuration
- Index