JBL Synthesis SDA 4600 User Manual

JBL Synthesis Receivers and Amplifiers

Advertising
background image

JBL SYNTHESIS SDA8300 / SDA4600 QUICKSTART

1 |

J B L S y n t h e s i s S D A A m p l i f i e r Q u i c k S t a r t G u i d e

General Information /

一般信息 / 一般資訊

IF YOU READ NOTHING ELSE IN THIS GUIDE READ THIS INFORMATION:

WARNING: Before you start to set up you’re amplifier and observe the Important Safety Instructions
found at the beginning of this manual.

The SDA amplifiers come pre-configured to work with the SDEC4500P using the BLU-LINK digital audio signal over
Cat5e Ethernet cables. The amplifiers should not be connected to the home network. Analog audio input comes IN on the
SDEC4500P (up to 12 channels) and OUT on the SDA8300 and/or SDA4600 without going through any Digital to Analog
conversions (up to 20 Channels as standard, expandable to 128 channels).

Two alternate configurations are selected by using the included selection trigger that plugs into the GPIO input on the rear
panel.

The SDA8300 amplifier ships configured for a simple 7-channel system. The SDA8300 can access two (2) additional
configurations. Using combinations of these configurations allows the system to output from a simple 7 x 300 Watt system
to up to 16 x 300 Watts with discrete DSP for each channel with active bi-amp outputs on the Left-Center-Right.

The SDA4600 ships configured for a 4-channel subwoofer (4x600 Watts). Up to two (2) additional configurations can be
accessed for bridged high power subwoofers outputs (2x1200 Watts) with discrete channel DSP for each output. These
are used with the Harman Patented “Sound Field Management” in the SDEC4500P.

The SDEC-4500P controls all DSP and BI-

AMP speaker crossover settings and must be configured with either “JBL

Synthesis ARCOS” software or “SDEC Control Panel Software v1.5”. Go to www.jblsynthesis.com to download the correct
software.

请仔细阅读以下信息:

警告:开始设置功放前,请先参阅本手册开头的“重要安全指引”。

SDA

功放出厂时已做好相应配置,通过 Cat5e 以太网电缆传输 BLU-LINK 数字音频信号,开箱即可配合 SDEC4500P 使用。

请勿将功放连接至家庭网络。模拟音频的输入采用 SDEC4500P(最多 12 个声道),输出采用 SDA8300 和/或 SDA4600,
而不是采用数字到模拟转换(标准最多 20 个声道,可扩展至 128 个声道)。

使用随附的选择触发器可在两个天线配置之间进行选择。该触发器插接到后面板 GPIO 输入。

SDA8300

功放在出厂发货时已配置妥善,开箱即可配合简单的 7 声道系统使用。SDA8300 可添加两 (2) 个额外配置。组

合使用这些配置,可在左-中-右设置中采用有源双功放输出,让每个声道都支持离散 DSP,让简单的 7 x 300 W 系统也能
够发出 16 x 300 W 的效果。

SDA4600

出厂发货时已配置妥善,开箱即可配合 4 声道低音炮 (4 x 600 W) 使用。还可以额外添加两 (2) 种配置,以支持

桥接的高功率低音炮输出 (2 x 1200 W),让每个输出都能实现离散声道 DSP。这些都是全赖于 SDEC4500P 中加入了

Harman

专利技术“声场管理”。

SDEC-4500P

能控制所有 DSP 和双功放扬声器分频设置,在设置时必须使用“JBL Synthesis ARCOS”软件或“SDEC 控制

面板软件 v1.5”。要下载软件,请访问 www.jblsynthesis.com。

标识含义:加贴该标识的设备仅按海拔 2000m 进行安全设计与评估,因此,仅适用于在海拔

2000m

以下安全使用,在海拔 2000m 以上使用时,可能有安全隐患.


如果您打算不閱讀本指南中的其他內容,請務必閱讀以下資訊:

Advertising
This manual is related to the following products: