Sealey AK436 User Manual
Rechargeable spotlight 3 million candle power, Ak436.v3, Instructions for
INSTRUCTIONS FOR:
RECHARGEABLE SPOTLIGHT
3 MILLION CANDLE POWER
MODEL NO:
AK436.V3
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you
years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE
AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.
SAFETY INSTRUCTIONS
1.1. GENERAL SAFETY
Ensure the spotlight is correctly charged before initial use.
When fully charged, spotlight must not be used continuously for more than 20 minutes. To do so may damage the spotlight.
WARNING! The lens becomes very hot during operation.
DO NOT cover or block the lens during use.
DO NOT turn the spotlight on when it is being re-charged.
DO NOT shine directly into your, other person’s or animal’s eyes.
DO NOT stand the spotlight near any surface or item that may be adversely effected by the heat emitted by the lens.
DO NOT allow children to use the spotlight.
DO NOT handle or move the spotlight whilst it is being charged.
DO NOT use the spotlight if you suspect that the battery or the spotlight casing is damaged.
DO NOT handle the bulb with your fingers. Use a soft lint-free cloth.
Ensure that correctly rated battery and bulb are used for replacements.
When not in use store the spotlight in a safe, dry, childproof location.
1.2. BATTERY SAFETY
DANGER! BE AWARE, LEAD-ACID BATTERIES MAY BE DANGEROUS IF NOT HANDLED WITH CARE AND ACCORDING TO THESE
INSTRUCTIONS.
,
Before exposing the battery for replacement, remove personal metallic items such as rings, bracelets, necklaces and watches. A lead-acid
battery can produce a short-circuit current high enough to weld a ring to metal, which would cause severe burns.
DO NOT smoke or allow a spark or flame in the vicinity of battery.
Ensure the charger is switched off and disconnected from the spotlight before attempting to open the lamp unit.
If the battery or wire terminals are corroded or dirty, clean them before replacing battery.
DO NOT disassemble the battery for any reason.
WARNING! DO NOT allow metal tools to touch both battery terminals simultaneously. Arcing or short circuit will result.
DO NOT allow battery wires to touch each other or to make contact with any other metallic part.
DO NOT cross-connect wires to the battery as this will damage the unit.
Ensure positive (+) (RED) is to positive and negative (-) (BLACK) is to negative.
DO NOT leave battery in a discharged state, recharge battery immediately. If the lantern is not in use, recharge the battery every three months.
Dispose of the old battery in accordance with local authority battery regulations.
DO NOT dispose of with regular refuse.
1.3. ELECTRICAL SAFETY.
ONLY USE THE SUPPLIED CHARGER PLUG FOR CONNECTING SPOTLIGHT TO THE POWER SUPPLY.
ONLY USE THE SUPPLIED ADAPTOR FOR CONNECTING TO A VEHICLE 12V SOCKET.
WARNING! It is the user’s responsibility to read, understand and comply with the following electrical instructions with respect to the charger
plug:
You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices. An RCCB (Residual Current Circuit
Breaker) should be incorporated in the main distribution board. We also recommend that an RCD (Residual Current Device) is used with all
electrical products, particularly portable equipment which is plugged into an electrical supply not protected by an RCCB.
You must also read and understand the following instructions concerning electrical safety.
1.3.1. The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified
electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.3.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance and the
safety of the appliance operator.
If in any doubt about electrical safety, contact a qualified electrician.
1.3.3. You must ensure that you:
Inspect the charger plug, cable and connector for wear and damage to ensure items are safe before connecting to the mains power supply.
If worn or damaged
DO NOT use.
Check cables are always protected against short circuit and overload.
Important: Check that the voltage marked on the charger plug is the same as the power supply to be used.
Uncoil the cable between charger and the spotlight.
DO NOT pull the charger plug from the mains socket by the lead.
DO NOT use any other type of charger with this product.
DO NOT place the connector into any area of the spotlight except the correct jack inlet socket.
DO NOT try to take the charger plug apart.
DO NOT use the charger plug to charge or power any other electrical item.
DO NOT get the charger wet, or use in wet, damp conditions (for indoor use only).
WARNING! NEVER substitute a standard 13 amp 3 pin plug, or any other type of plug, for the charger plug.
Original Language Version
AK436.V3 Issue: 2 - 18/01/12