Sealey EH15001 User Manual

Industrial fan heaters output 5kw, 9kw, 15kw, Instructions for, Model nos

Advertising
background image

INSTRUCTIONS FOR:

INDUSTRIAL FAN HEATERS

Output 5kW, 9kW, 15kW,

MODEL Nos:

EH5001, EH9001, EH15001

1.2. GENERAL SAFETY
1.2.1. MAINTENANCE PRECAUTIONS

WARNING! Disconnect the heater from the mains power

supply, before servicing or performing any maintenance.

Servicing or maintenance must only be carried out by an

authorised service agent.

Check that the heater is in sound condition and good working

order. Take immediate action to repair or replace damaged

parts.

Use recommended parts only. Unapproved parts may be

dangerous and will invalidate the warranty.

DO NOT attempt to repair a damaged heater, contact an

authorised service agent.

1.2.2. POSITIONING OF HEATER

WARNING! DO NOT use the heater near flammable material,

liquids, solids, gases or compressed gas cylinders etc.

DO NOT place the heater close to a bath, wash basin, shower,

swimming pool or any other water-filled area or wet surface.

DO NOT place the heater up against any surface such as a

wall, door or furniture etc.

DO NOT place the heater immediately below any electrical

outlet.

Position the heater at least a minimum of 0.5mtr at the rear

and sides, and 2mtr at the front, from any walls or objects.

DO NOT place the heater on a raised surface or anywhere

where it could topple over.

Original Language Version

EH15001, EH9001, EH5001 Issue: 6(L) - 05/05/15

1.1. ELECTRICAL SAFETY

WARNING! ELECTRICAL INSTALLATION OF THE HEATER

TO A 3-PHASE 415VOLT SUPPLY MUST ONLY BE

CARRIED OUT BY A QUALIFIED ELECTRICIAN.

Make sure the power supply cable is correctly connected

to the earth. It is the user’s responsibility to read,

understand and comply with the following:

You must check all electrical equipment and appliances to

ensure they are safe before using. You must inspect power

supply leads, plugs and all electrical connections for wear and

damage. You must ensure the risk of electric shock is

minimised by the installation of appropriate safety devices. An

RCCB (Residual Current Circuit Breaker) should be

incorporated in the main distribution board. You must also read

and understand the following instructions concerning electrical

safety.

1.1.1. The Electricity At Work Act 1989 requires all portable

electrical appliances, if used on business premises, to be tested

by a qualified electrician, using a Portable Appliance Tester

(PAT), at least once a year.

1.1.2. The Health & Safety at Work Act 1974 makes owners of

electrical appliances responsible for the safe condition of the

appliance

and the safety of the appliance operator. If in any

doubt about electrical safety, contact a qualified electrician.

1.1.3. Ensure insulation on all cables and the product itself is safe

before connecting to mains power supply.

1.1.4. Ensure that cables are always protected against short circuit

and overload.

1.1.5. Regularly inspect power

supply, leads, plugs and all

electrical connections for

wear and damage,

especially power

connections, to ensure that

none are loose.

1.1.6. Important: Ensure the

voltage marked on the

product is the same as the

electrical power supply to

be used. A three phase

plug must be fitted to this

machine.

1.1.7.

DO NOT pull the powered appliance by the power cable.

1.1.8.

DO NOT pull power plugs from sockets by the power cable.

1.1.9.

DO NOT use worn or damage leads, plugs or connections.

Immediately replace or have repaired by a qualified electrician.

1.1.10. This product must be fitted with a 3-phase plug according

to the diagram, and will require a minimum of, 16Amps

per phase for EH5001 and EH9001, and 32Amps for

EH15001, of electrical supply. You must contact a qualified

electrician to ensure an appropriately fused supply is

available.

Connect GREEN/YELLOW wire to earth (E)

terminal . Connect the live wires to live 1, 2 and 3.

When completed, check that there are no bare wires, that all

wires have been connected correctly, that the cable external

insulation extends beyond the cable restraint and that the

restraint is tight.

EH5001

EH9001

© Jack Sealey Limited

1. SAFETY

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT

CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL

INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions

and maintained properly, give you years of trouble free performance.

Refer to

Instructions

Indoor Use

Only

Advertising
This manual is related to the following products: