Sealey HVF20PO User Manual

Hvf20po, Recommended fuse rating: 3a, Safety instructions for

Advertising
background image

1.1.

ELECTRICAL SAFETY

WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:

You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other

connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices.

A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also recommend that a Residual Current

Device (RCD) is used. It is particularly important to use an RCD with portable products that are plugged into a supply which is not protected by an

RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current Device by contacting your Sealey dealer.

You must also read and understand the following instructions concerning electrical safety.

1.1.1. The

Electricity at Work Act 1989 requires that all portable electrical appliances, if used on business premises, are tested by a qualified

electrician, using a Portable Appliance Tester (PAT), at least once a year.

1.1.2. The

Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances

and the safety of the appliance operators.

If in any doubt about electrical safety, contact a qualified electrician.

1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.1.1. and 1.1.2.

and use a Portable Appliance Tester.

1.1.4. Ensure that cables are always protected against short circuit and overload.

1.1.5. Inspect power supply cables and plugs regularly for wear or damage and check all connections

to ensure that none is loose.

1.1.6.

Important: Ensure that the voltage marked on the appliance matches the power supply

to be used and that the plug is fitted with the correct fuse - see fuse rating at right.

1.1.7.

DO NOT pull or carry the appliance by the power cable.

1.1.8.

DO NOT pull the plug from the socket by the cable.

1.1.9.

DO NOT use worn or damaged cables, plugs or connectors. Have any faulty item repaired or

replaced immediatelyby a qualified electrician. When a BS 1363/A UK 3 pin plug is damaged,

cut the cable just above the plug and

dispose of the plug safely.

Fit a new plug according to the following instructions (UK only).

a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.

b)

Connect the BROWN live wire to the live terminal ‘L’.

c) Connect the BLUE neutral wire to the neutral terminal ‘N’.

d) After wiring, check that there are no bare wires, that all wires have been correctly

connected, that the cable outer insulation extends beyond the cable restraint and that the

restraint is tight.

Double insulated products, which are always marked with this symbol , are fitted with live (brown) and neutral (blue) wires only.

To rewire, connect the wires as indicated above -

DO NOT connect either wire to the earth terminal.

1.1.10. Products which require more than 13 amps are supplied without a plug. In this case you must contact a qualified electrician to ensure that

a suitably rated supply is available. We recommend that you discuss the installation of an industrial round pin plug and socket with your

electrician.

1.1.11. If an extension reel is used it should be unwound fully before connection. A reel with an RCD fitted is preferred since any appliance

plugged into it will be protected. The cable core section is important and should be at least 1.5mm², but to be absolutely sure that the

capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use of

2.5mm² section cable.

1.2. GENERAL SAFETY

Disconnect the fan from the mains power when not in use, and before servicing or performing any maintenance.

Use the fan in dry areas only.

DO NOT use in wet or areas with high condensation such as showers, pools etc.

WARNING! If the fan falls into water or other liquid, switch off and disconnect from the mains power supply immediately. DO NOT touch the

fan until the mains power supply has been disconnected.

Always disconnect the fan from the power supply when moving it from one location to another and ensure fan stands on a level surface.

The fan air flow is powerful. Before using ensure there are no materials or items that may be blown about by the stream of air.

Keep the fan clean and maintained in good condition. For electrical components or motor service contact an authorised service agent.

Use recommended parts only (unapproved parts may be dangerous, and will invalidate your warranty).

DO NOT operate the fan where there are harmful, explosive or flammable gases, fumes or hazardous substances.

DO NOT stand the fan on the electrical power cable.

DO NOT insert any objects through the fan guard.

DO NOT cover the fan when in use.

DO NOT immerse the fan in water or any other liquid.

DO NOT allow children to operate the fan.

DO NOT stand the fan where it may be knocked over or off a surface, or where the lead may cause a person to trip.

DO NOT use the fan outdoors.

DO NOT modify speed control or attempt to fit any additional external speed control device to the fan.

When not in use cover the fan to protect from dust, and store in a safe, dry, childproof location.

1. SAFETY

INSTRUCTIONS FOR:

INDUSTRIAL HIGH VELOCITY OSCILLATING

PEDESTAL FAN 20"

MODEL No:

HVF20PO

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly

maintained, give you years of trouble free performance.

Original Language Version

HVF20PO Issue: 1 11/12/14

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT

CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL

INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

© Jack Sealey Limited

Recommended Fuse

Rating: 3A

Refer to

Instructions

Advertising