Livarno Z29618-BS - Manual

GR / CY GB / IE / CY GB / IE / CY GB / IE / CY GB / IE / CY GB / IE / CY GB / IE / CY
GB / IE / CY
GB / IE / CY
protective surround. Then hold the LED work lamp
against a magnetic surface.
Q Using the LED work lamp
disconnected from a power
supply
j Fully charge the LED work lamp, as described
in the section on “Charging the LED work
lamp”.
j Set the ON / OFF switch 5 to position I to
switch on the LED work lamp.
j Set the ON / OFF switch 5 to position 0 to
switch off the LED work lamp.
of damage.
J CAUTION! DANGER OF
EXPLOSION! Do not operate
the LED work lamp in potentially
explosive environments in which there are
inflam mable vapours, gases or dusts.
J The LED work lamp is protected against water
spray. However, the product, mains adapter
and car adapter must never be immersed in
water or other liquids. Failure to observe this
advice will create the risk of electric shock!
Never hang the product near a washbasin,
pond and the like.
J Connect the LED work lamp to a properly
installed mains socket or a suitable cigarette
lighter socket only. The voltages in each case
must comply with information given in the
section “Technical data”.
start to use the LED work lamp again.
Otherwise water could enter the power input
connection socket 6 if the LED work lamp is
used outdoors.
Q Use
CAUTION – RISK OF ACCIDENT! If at
all possible, do not use the LED work lamp in a
moving vehicle. If the LED work lamp is used in a
vehicle, it must not be allowed to endanger the
safety of the driver or passengers. Always store
and secure the LED work lamp in such a way that
there is no risk of injury from or damage to the
product, even during full braking.
Note: You can secure the LED work lamp in
place using the hook 1 or magnetic mount 2 .
Clamp the magnetic mount 2 to the LED’s
Safety instructions
J Always keep children away from
the packaging material. This
product is not a toy.
J Children or persons who lack the knowledge
or experience to use the device or whose
physical, sensory or intellectual capacities are
limited must never be allowed to use the
device without supervision or instruction by a
person responsible for their safety. Children
must never be allowed to play with the device.
J This product is not a toy and should be kept
out of the reach of children. Children are not
aware of the dangers associated with
handling electrical products.
J Do not use the article if you detect any kind
and their opening hours can be
obtained from your local authority.
Defective or exhausted rechargeable batteries
must be recycled in accordance with Directive
2006 / 66 / EC. Return the battery and / or the
device through the appropriate collection facilities.
Pb
Improper disposal of
rechargeable batteries can
damage the environment!
Rechargeable batteries must not be disposed of
with the household refuse. They may contain toxic
heavy metals and require to be handled as special
waste. The chemical symbols of heavy metals are:
Cd = cadmium, Hg = mercury, Pb = lead.
free cloth. Use a slightly moist cloth to remove
any stubborn dirt.
Q Disposal
The packaging is made entirely of
recyclable materials, which you may
dispose of at local recycling facilities.
Contact your local refuse disposal authority for
more details of how to dispose of your worn-out
product.
To help protect the environment,
please dispose of the product properly
when it has reached the end of its
useful life and not in the household
waste. Information on collection points
Fault Possible causes and cures
Charging
takes a
very long
time
When connected to a
cigarette lighter socket:
- Vehicle battery too weak?
Q Maintenance and cleaning
The product requires no maintenance. The LEDs
cannot be replaced.
J Switch off and disconnect the product from
the power supply before you clean it.
J Never immerse the product in water or other
liquids.
J Do not use corrosive cleaning agents.
j Clean the product regularly with a dry, fluff-
Q Troubleshooting
Fault Possible causes and cures
No
functions
- Mains adapter 3 or car adapter
4 is not fully inserted.
Indicator
LED 7
does not
illuminate
When connected to a
cigarette lighter socket:
- Is the cigarette lighter socket
supplied with power? Some
cigarette lighter sockets only
supply power with the ignition
switched on.
- Check the fuse in the vehicle.
GB / IE / CY GB / IE / CY GB / IE / CY GB / IE / CY GB / IE / CY GB / IE / CY
GB / IE / CY GB / IE / CY GB / IE / CY
J Ensure that the electrical socket is easily
accessible so that you can pull the plug
quickly out of the socket if necessary.
J Do not carry out any modifications or repairs
to the product yourself. The LEDs cannot and
must not be replaced.
CAUTION! The protective surround to the
LEDs cannot be replaced. Dispose of the LED
work lamp if you discover cracks or signs of
fracture on the protective surround.
J Dispose of the product if the LED work lamp,
mains adapter or car adapter is damaged.
J Never connect the LED work lamp to a power
supply socket if the LED work lamp, power
lead or socket is damaged or the LED work
lamp has been dropped.
J Ensure that the power lead cannot become
damaged by sharp edges or hot objects.
Unwind all the lead completely before use.
J Keep easily flammable materials away the
product. Never hang objects above the LED
work lamp or the mains adapter and never
cover them.
J Pull the mains adapter / plug out of the mains
socket / cigarette lighter socket when you are
not using the LED work lamp or before you
clean it. Do this as well if signs of a fault
develop during use or charging, e.g. smoke,
burning smell etc., or during a storm. When
doing this, pull directly on the mains
adapter / plug and not on the lead.
J Protect the product against heat, cold, strong
vibrations and impacts.
J Do not attach the hook 1 to hot objects. The
dead weight of the LED work lamp might
cause the hook to deform or bend out of shape.
Q Before use
Q Charging the LED work lamp
Note: You can charge the LED work lamp from
an ordinary domestic mains power outlet or from
the cigarette lighter socket in your vehicle.
Note: The fuse of the car adapter is replaceable.
The specification must comply with information
given in the section “Technical Data”. The fuse
may only be replaced by a qualified electrician
(see Fig. A).
Tip: We recommend that you charge the LED
work lamp from an ordinary domestic mains
power outlet to avoid draining your vehicle’s
battery.
CAUTION! Do not connect the LED work lamp
to the cigarette lighter socket of your vehicle if the
vehicle battery is old or degraded. Failure to
observe this advice may result in your vehicle’s
engine not starting.
Note: To use the LED work lamp without an adapter,
you must first charge the integral rechargeable
batteries. It takes between 4 and 6 hours to
charge the integral batteries. The rechargeable
batteries are permanently installed in the handle
of the LED work lamp.
Note: Charge the LED work lamp for
approximately 12 hours before first use.
Note: Charge the LED work lamp at least once
a month, if it is to remain unused for an extended
period of time.
Note: If the LED work lamp has not been
charged for an extended period of time (approx.
2 months), you could find that the integral
rechargeable batteries have entered a dormant
state. Charge and discharge the LED work lamp a
number of times in succession to reactivate the
integral rechargeable batteries.
j Switch off the LED work lamp during the
charging process (set the ON / OFF switch
5 to position 0).
j Remove the rubber protection cap from the
bottom of the LED work lamp.
j Insert the power output connection plug of
the mains adapter 3 or the car adapter 4
into the power input connection socket 6 in
the handle of the LED work lamp.
Note: During charging from a cigarette
lighter socket, ensure that the plug is always
completely inserted into the cigarette lighter
socket of the vehicle. Failure to observe this
advice may result in risk of fire from
overheating.
j Insert the mains adapter 3 into a mains
socket or the car adapter 4 into the
cigarette lighter socket of your vehicle.
Note: The product has an overcharging
protection system. Nevertheless, you should
disconnect the LED work lamp from the mains
once the charging process is complete.
Note: The indicator LED 7 illuminates red
during the charging process. When the
charging process is complete, the indicator
LED 7 illuminates green. When the indicator
LED 7 illuminates green, pull the mains
adapter 3 out of the mains socket or the car
adapter 4 out of the cigarette lighter socket.
Disconnect the adapter from the LED work
lamp to prevent the batteries from
discharging themselves.
j Place the rubber protection cap back on the
power input connection socket 6 before you
LED Work Lamp
Q Proper use
The product is intended for providing illumination
in dry indoor rooms and in outdoor environments.
If used outdoors the mains adapter must be
protected from moisture and the weather. The
product is not intended for commercial use.
Q Description of parts and
features
1 Hook
2 Magnetic mount
3 Mains adapter
4 Car adapter (for cigarette lighter socket)
5 ON / OFF switch
6 Power input connection socket
7 Indicator LED
Q Technical data
Light bulb: 23 LEDs (white,
non-replaceable)
Light intensity : approx. 12,000 mcd
(millicandela)
Lamp rechargeable
batteries: 3 x AA NiMH, 1000 mAh
(not replaceable)
Charging time: approx. 4 to 6 hours
Burn time: approx. 4 hours (with fully
charged battery)
Lifespan of LEDs: approx. 20,000 hours
Protection class:
System of protection: IP44
Adapter:
Input: 230-240 V ~ 50 Hz
Output: 6 V , 300 mA
Model: SD-6300
Protection class:
System of protection: IP20
Cigarette lighter:
Input: 12 V
Output: 12 V , 240 mA
Replaceable fuse: U5F, 250 V ~, 350 mA,
ø 5 x 20 mm
Q Scope of delivery
1 LED work lamp
1 Mains adapter
1 Car adapter for cigarette lighter socket
1 Magnetic mount
1 Operating instructions
2
3
4
1
7
6 5
Z29618-BS
A
LED WORK LAMP
Operation and Safety Notes
ΛΑΜΠΑ-LED
Υποδείξεις χειρισμού και ασφαλείας
EMC
87697_GB-IE-CY.indd 1 1/15/2013 4:52:31 PM